Using The Wake Up Timer - Sanyo DC-LD5 Instruction Manual

To check the timer settings:
1. Press the TIMER switch. The timer ON time setting is
displayed for 5 seconds.
2. Press the TIMER switch before the 5 seconds elapse.
The timer OFF time setting is displayed for 5 seconds,
3. Press the TIMER switch before the 5 seconds elapse.
The timer operation source is displayed for 5 seconds.
If the tuner is being used as the
source,
the band,
preset number and frequency will be displayed for 5
seconds when the TIMER switch is pressed before
the 5 seconds elapse after step 3.
4. If the TIMER switch is pressed within the 5 seconds, a
return is made to the original display.
A return will be made to the original display unless the
operations in steps 2 to 4 above are performed before
the 5 seconds elapse.
To change the settings, indicate the setting which is to
be changed by performing steps 1,2 and 3, and press
the MEMORY switch so that the display blinks. Then
proceed according to the instructions in the "ON/OFF
timer settings" section.
To set the timer again using the same settings:
Press the TIMER switch. The timer ON time is displayed
- for 5 seconds.
2, The operation standby mode is established when the
SET switch is pressed while the timer ON time is dis-
played.
Every time above steps 1 and 2 are repeated, the mode
alternates between operation standby and release
(present time display only).
3. Press the POWER switch to switch off the power.
.
~._
Unless the power is switched off, the timer will not be
activated at the set time, and the timer mode will be
released.
If the CLEAR switch is pressed while the timer is being
set or its settings are being checked, the mode in
question will be released and a return made to the
original display.
To switch off the power during an operation based on
the timer, operate the POWER switch. The ON/OFF timer
will then be released.
USING THE WAKE UP TIMER
First set the wake-up time and source (including the band
and preset station for the tuner) which is to be heard. At the
set time, the set source will be heard, and the power will be
turned off after 60 minutes. Once the WAKE UP timer has
been set, it will function every day unless released.
1.
2.
3.
4.
Set the wake-up time and source to be heard. (See
"WAKE UP timer settings" section.)
Prepare to operate the source which is to be heard.
Listen to the sound of the source and set the volume
and tone quality controls as desired.
Check the timer settings. (See "To check the timer
settings" section.)
Check that "WAKE UP" is displayed, and then press the
POWER switch to turn off the power.
Press the POWER switch to turn off the power when the
power is turned on at the wake-up time.
m
Even after the WAKE UP timer has finished operating,
the "WAKE UP" display is not cleared and the operation
standby mode continues.
WAKE UP timer settings
1. Press the WAKEUP switch. "WAKE UP" and the previ-
ous wake-up time setting are displayed for 5 seconds.
eg: WAKE UP 5:30 AM
2. Press the MEMORY switch before the 5 seconds elapse.
"WAKE UP" and the hours display blink.
WAKE UP
5:30 AM
3. Set the wake-up time by pressing the UP and DOWN
switches and then MEMORY switch.
WAKE UP 6:00 AM
WAKE UP SOURCE TAPE
The previous source setting display blinks.
4. Select the source using the UP and DOWN switches and
MEMORY switch.
- Every time the UP switch is pressed, the source
changes in the following sequence (or in the reverse
sequence if the DOWN switch is pressed):
dlSC - TAPE - TU - dlSC -...
A return is made to the original display after 1 second,
and the wake-up operation standby mode is established
automatically. (The "WAKE UP" display remains.)
Waking up to the sound of the radio
1. Perform step 4 above until "TU" appears on the display.
When the MEMORY switch is pressed, the band, preset
number and frequency of the previous timer operation
are displayed,
2. Select the band using the BAND SELECT switch, and
indicate the desired preset number using the UP and
DOWN switches or the PRESET 12KEY switches on the
remote controller.
3. Press the MEMORY switch.
To check the timer settings
1. Press the WAKEUP switch. The wake-uptime setting is
displayed for 5 seconds.
2. Press the WAKEUP switch before the 5 seconds elapse.
The timer operation source is displayed for 5 seconds.
If, with the tuner, the WAKE UP switch is pressed
within 5 seconds after step 2, the band, preset num-
ber and frequency will be indicated for 5 seconds.
3. If the WAKEUP swit~h is pressed before the 5 seconds
elapse, a return is made to the original display.
To change the settings, perform steps 1 and 2 to display
the setting which isto be changed, and press the MEMORY
switch to make the display blink on and off. Then proceed
in accordance with the instructions given in "WAKE UP
timer settings".
To release the WAKE UP timer
1,
2.
Press the WAKE UP switch. The wake-up time is dis-
played for 5 seconds.
If the SET switch is pressed while the wake-up time is
displayed, it will be released.
Only the present time will remain on the display.
-24-