SATO CL612e Service Manual page 245

Rear Panel 1-3
Receive Buffer Hex Dump 8-17
Receive Buffer Selection 2-3
Receive Buffer 3-3
Repeat Print 3-13
Replacing Notch/Gap and Eye-Mark Sensors 6-30
Replacing the Display Panel 6-37
Replacing the Fuses 6-7
Replacing the Keyboard 6-37
Replacing the Main Circuit Board 6-2
Replacing the Paper End Switch 6-30
Replacing the Platen 6-19
Replacing the Power Supply 6-9
Replacing the Print Head 6-16
Replacing the Ribbon Drive Clutch Washers 6-23
Replacing the Ribbon Motion Sensor 6-27
Replacing the Stepper Motor 6-12
Replacing the Timing Belts 6-13
Replacing the Top Half of the Notch/Gap Sensor 6-34
Reprint W/Feed 2-28
Resetting the Print Server 8-9
Rewind Clutch 5-3
Rewind Drive Spindle 6-24
Rewind Spindle 6-15
Rewinder Assembly 9-7
Ribbon Assembly 10-22
Ribbon Boss 6-26
Ribbon Clutch Adjustments 5-2
Ribbon Core 5-3
Ribbon Guide Plate 1-7, 6-17
Ribbon LED 1-5
Ribbon Motion Sensor 6-29
Ribbon Rewind Clutch Adjustment 5-4
Ribbon Rewind Spindle 1-4, 5-3, 6-24
Ribbon Roller Adjustment 5-8
Ribbon Sensor Adjustment 4-14
Ribbon Sensor Verification 4-13
Ribbon Sensor 1-8
ribbon supply spindle 1-4
Ribbon Unwind Clutch Adjustment 5-2
Ribbon Unwind Spindle 5-3, 1-4
Ribbon 1-10
RS232 Transmit/Receive Setting 2-2
RS232C (Serial) Interface 8-4
RS232C Interface Signals 3-8
RS232C Serial Interface 3-2
S
Sample Test Labels 2-40
Sample Test Prints 7-7
Select Language 2-30
Sensor Locations 6-30
Sensor Type Selection 2-3
PN 9001079
Rev. B
Sensors and Switches 1-8
Set Calendar 2-14, 9-24
Single Job Buffer 3-3
Software Default Settings 2-7
Spare Parts List 10-1
Standard Operation 3-12
Stay 5-6
Stepper Motor 1-7
Stop Bit Selection 2-2
Switch Selections 2-7
Switches and Sensors 1-4
T
TCP/IP Troubleshooting 8-6
Test Point Chart 4-5
Test Print Mode 2-33
Test Print Mode Configuration 2-33
Test Print Size 2-34
Test Print 5-6
Timing Belt Tension Adjustment 5-11
Timing Belt 1-7
TP Test Module 4-4, 4-5
Troubleshooting Check List 8-2
Troubleshooting Tables 8-11
Troubleshooting 8-1
U
Universal Serial Bus (USB) Interface 3-9, 8-4
Unwind Clutch 5-3
Unwind Drive Spindle 6-24, 5-3
USB Interface 3-2
V
VR1 (Print) 1-6
VR2 (Offset) 1-6
VR3 (Pitch) 1-6
VR4 (Display) 1-6
W
Washer, Oil-less 6-26
Windows 95/98 Peer-to-Peer Troubleshooting 8-9
Windows NT/LAN Server Troubleshooting 8-8
X
X-On/X-Off Flow Control 3-9
SATO CL608e/CL612e Service Manual
Index
Index-3