Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for fadini Girri 130
Summary of Contents for fadini Girri 130
- Page 1 INSTALLATION MANUAL ®...
- Page 2 ELECTRO-MECHANICAL SLIDING GATE OPERATOR CUT AWAY SIDE VIEW OF THE ELECTRO-MECHANICAL OPERATOR GIRRI 130 FOR SLIDING GATES COVER LID BACK COVER OPTIONAL FAN COVER ELPRO 15 PLUS CONTROL BOX OPTIONAL COOLING FAN GENERAL LINE SWITCH 137 ELECTRIC MOTOR CUT OFF LIMIT...
- Page 3 FIXING DETAIL WITH PARTS LAYOUT OF THE ELECTRO-MECHANICAL GATE OPERATOR GIRRI 130 INSTRUCTIONS FOR THE INSTALLATION OF GIRRI 130 ON TO SLIDING GATES To achieve a perfect application and performance of GIRRI 130, you must follow the steps and the drawings here below: COVER...
- Page 4 4 long bolts so that the threads are all out. Set the plate horizontally levelled as shown in the illustration at 80 mm from REFERENCE LINE the gate. Corner “A” of GIRRI 130 base plate is to coincide with the reference line drawn on the fixing base plate. FIXING...
- Page 5 REMOVE THE LID FROM THE COVER LOCK WITH KEYS GATE WHEEL TIGHTEN FOR AUTOMATIC MOVEMENTS RELEASE KNOB PIC. 5 Remove the cover to lock or release the operator (Pic. 5-6). PIC. 6 To release for manual operations 3 turns anti-clockwise. FIXING NUT OPERATOR BASE PLATE Once fixed the operator on its concrete mounting you can carry...
- Page 6 1 - Remote-controlled switch receiver CRUASTRO 11 - Rack 2 - Flashing lamp MIRI 4 12 - Geared motor GIRRI 130 c/w Elpro 15 Plus control board and 3 - Photocell receiver TRIFO 11 plug-in radio receiver PCB Astro 43/2 R...
- Page 7 For the application of the “CE” mark it is recommended to have the operator fitted with item No. 137 the line switch. - This switch is fitted on the customer’s request if an order for GIRRI 130 with CE sticker on it is received. ELECTRICALLY OPERATED GATES s.n.c.
- Page 8 24V Protection The electronic control panel Elpro 15 Plus, new generation, is designed to operate the sliding gate operator Girri 130. Power supply is 230V 50Hz single-phase. Built in full compliance with BT 93/68/CE Low Voltage and EMC 93/68/CE Electro-Magnetic Compatibility Regulations.
- Page 9 PLUS ELECTRICAL POWER CONNECTIONS Flashing lamp: Capacitor and Single-phase Motor: Power supply: DIP-SWITCH 4 and 7: ON: Pre-flashing OFF: No pre-flashing MOTOR RUN TIME DWELL TIME MOTOR ON: Lamp is not operating during OPEN/CLOSE from 2 up to 255s TORQUE Dwell time.
- Page 10 “General Line Switch” electric current inlet (Pic. 14). IN I F A D 5 P L .E 0 1 /0 2 /0 C O D D :0 4 P R O 0 V A P N :1 1 5 V 2 X 1 P R I: V - 5...
- Page 11 YELLOW-GREEN WIRE EARTH MOTOR CAPACITOR BLUE LIMIT SWITCH CABLE I N I F A D 5 P L .E 0 1 /0 2 /0 C O D D :0 4 0 V A P R O P N :1 1 5 V 2 X 1 P R I: V - 5...
-
Page 12: Technical Specifications
AUTOMATIC GATE MANUFACTURERS The manufacturers reserve the right to change the products without any previous notice Via Mantova, 177/A - 37053 Cerea (Verona) Italy - Tel. +39 0442 330422 r.a. - Fax +39 0442 331054 - e-mail: info@fadini.net - www.fadini.net...