Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Kurt DL640
Summary of Contents for Kurt DL640
- Page 1 Model: DL640 DL430 CT640 CT430 Installation & Operation Guide P/N DL640-95, REV C...
- Page 2 DoubleLock vise. You will find modifications have been made that are different from the past DoubleLocks. Kurt's new DoubleLock has a design that fits current user needs and meets their expectations of a simple, functional vise. The new DL640, DL430, CT640, and CT430 maintains the 3", and 4"...
- Page 3 Stationary Jaw setups or re-setup from a convertible model. 7. Convertible models- When the DL640 or DL430 is needed for a single large part clamping, the maximum opening is 10.69" to a minimum of 2.69", and 8.20" to 2.1" on the DL430. This is a continuous travel opening.
- Page 4 INSTALLATION AND MOUNTING INSTRUCTIONS INSTALLATION The Kurt DoubleLock Vise offers two clamping stations. This vise is ideal for clamping parts of the same size or dissimilar size, and can perform first and secondary operations simultaneously. It is packaged to prevent any damage to its components.
- Page 6 Holding Block Pre-load setup *PRE-LOAD PARTS. (* Is defined as ability to clamp one part first with limited pressure before second part is installed.) Caution: Pre-Load places only enough spring pressure to hold one part and are not intended to clamp part for machining. Both stations must be clamped to achieve clamping pressures.
- Page 7 Front Jaw Rear Jaw This setup will always clamp front part first . Once set it will release rear part first. Front Jaw Rear Jaw This setup will always clamp rear part first . Once set it will release front part first. Front Jaw Rear Jaw...
- Page 8 Pre-Load rangeAdjustment Nut Refer to sketch below for direction of adjustment To remove Pre-Load range (Reducing the amount of turns of the handle when clamping or unclamping parts). 1. Loosen but do not remove the (socket head set screw) on top of Holding Block.
- Page 9 Conversion Kit Assemble - DL640, DLM640 / DL430, DLM430 Refer to Conversion Kit Sketch on this page for setup preference. CAUTION USE CAUTION WHEN HANDING CHIP GUARD MATERIAL. EDGES AND CORNERS ARE SHARP AND MAY CAUSE PERSONAL INJURY IF NOT HANDLED PROPERLY.
- Page 10 General Cleaning/Maintenance Procedure 6/18/98 rev 1 DoubleLock Model # DL640, CT640, DL430, CT430 (metric included) TO ASSURE PROPER USAGE AND CONTINUOUS SERVICE OF YOUR DOUBLELOCK VISE, IT IS IMPORTANT TO REGULARLY CLEAN ANY MATERIAL BUILD UP THAT MAY HAVE OCCURED.
- Page 11 2. Before placing the (2) Movable Jaws over the Nuts make sure the segments are in the inside cavity using grease to hold them in place and for lubrication. 3. Spread a small amount of oil to the bed of the vise where the Moveable Jaws will be installed.
- Page 12 DL430...
- Page 13 DL640...
- Page 14 PRECAUTIONS When using the DoubleLock Vise in production, remember the following points: • Never use this vise as a Self Centering Vise. • See figure #3, page 14. Never clamp parts opposite from each other. • Always clamp directly across from each other or use a spacer to even clamping pressure points.
- Page 16 CUSTOMER SERVICE For additional information or question about your vise, Please contact Kurt Manufacturing at 1-800-328-2565 between the hours of 7:30 a.m. and 4:30 p.m. Central Standard Time. REPLACEMENT PARTS Contact your Kurt Manufacturing representative for a complete list of DoubleLock replacement parts and pricing.
- Page 17 REVISION A JULY 1998 COPYRIGHT 1998 KURT MANUFACTURING THIS DOCUMENT IS CONFIDENTIAL AND IS THE PROPERTY OF KURT MANUFACTURING. IT MAY NOT BE COPIED OR REPRODUCED IN ANY WAY WITHOUT THE EXPRESS WRITTEN CONSENT OF KURT MANUFACTURING. KURT MANUFACTURING INTENDS TO AND IS MAINTAINING THE WORK AS CONFIDENTIAL INFORMATION.