Advertisement
Quick Links
K U R T M A N U F A C U T R I N G -
L I F E T I M E I R O N C L A D
All Kurt Manufacturing Company industrial workholding products
and parts with the exceptions noted below, are warranted against
defects in material and workmanship for the life of the product or
part. (The life of the product is defined as that point in time when
such item no longer functions due to normal wear and tear.) Failure
to properly maintain and/or properly operate the product or part that
has been worn out, abused heated ground or otherwise altered, used
for a purpose other than that for which it was intended, or used in a
manner in consistent with any instructions regarding its use. The sole
obligation of Kurt Manufacturing Company, Inc. (Kurt) and the
purchaser's SOLE AND EXCLUSIVE REMEDY hereunder, shall be
limited to the replacement or repair of any Kurt product or part (by an
authorized Kurt technician) which are returned to Kurt Manufacturing
Company's place of business, transportation, shipping and postal
charges prepaid, and there determined by Kurt Manufacturing
Company to be covered by the warranty contained herein.
THE LIMITED WARRANTY DESCRIBED HEREIN IS
MADE
EXPRESSLY
IN
LIEU
EXPRESSED OR IMPLIED WARRANTIES, INCLDING
ANY IMPLIED WARRANTY OF MERCHANTABLITY OR
FITNESS FOR A PARTICULAR PURPOSE.
MANUFACTURING COMPANY IS NOT RESPONSIBLE
FOR THE IMPROPER USE OF ITS PRODUCTS. KURT
SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL
SPECIAL
OR
DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS
OF USE, REVENUE OR PROFIT.
KURT ASSUMES NO LIABILITY FOR, AND MAKES NO
WARRANTY REGARDING ANY PURCHASE ITEMS
WHERE THE MANUFACTURER OF SUCH ITEM
EXTENDS A SEPARATE WARRANTY.
9445 East River Road NW
Minneapolis, MN 55433
Phone: 877-226-7823
Fax: 877-226-7828
E-mail: workholding@kurt.com
Website: www.kurtworkholding.com
W A R R A N T Y
T M
OF
ANY
OTHER
KURT
CONSEQUENTIAL
KURT
3600A-Series Vise
"Air" Base Assembly
3600A - Forward
3610A - Reverse
3620A - Forward, Short
3630A - Reverse, Short
Operating Instructions Manual
Advertisement
Related Manuals for Kurt 3600A Series
Summary of Contents for Kurt 3600A Series
- Page 1 3630A - Reverse, Short purchaser’s SOLE AND EXCLUSIVE REMEDY hereunder, shall be limited to the replacement or repair of any Kurt product or part (by an authorized Kurt technician) which are returned to Kurt Manufacturing Company’s place of business, transportation, shipping and postal charges prepaid, and there determined by Kurt Manufacturing Company to be covered by the warranty contained herein.
- Page 2 Maintenance Log/Notes: _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ _____________________________________________________ Thank you! If you have any feedback or questions, please contact us at workholding@kurt.com or 877-226-7823.
-
Page 3: Troubleshooting Tips
Introduction Troubleshooting tips Thank you for purchasing a Kurt vise. You have just pur- The Kurt 3600-Series vise will operate mostly trouble free for chased one of the best machine vises in the industry. The Ver- many years. If properly maintained, this product is indestructible. -
Page 4: Setup Instructions
Now that you have your new Kurt 3600-Series vise, it’s time to set-up and begin using it. You will see that your new vise comes with a Kurt swivel handle, two chip guards (short & long) and an instruction manual along with the O-ring installation guide sup- plied in the shipping carton. - Page 5 If you need more clamping force you may need to upgrade the vise to a larger one. To properly clamp a part in your Kurt vise you should place the part in the center of the jaws resting on the ways of the vise.
- Page 6 15. Then turn the collar back TWO (2) more screw holes. This will allow proper distance for the collar to lock on the threads and keep the bearings firmly in place. (Items 15-16—See Fig. 2) 16. Install the four SHCS and make tight. 17.
- Page 7 9. Clean and inspect the counter bore, thrust washers and thrust bearing. 10. Apply water resistant grease to the thrust washer (i.e. Kurt lube p/n KLA or marine grade grease) 11. Install thrust bearing assembly on the screw in the reverse manner.
- Page 8 6. To re-assemble the movable jaw, apply a “glob” of grease to the under side of the movable jaw in the pocket. Place the spheri- cal segment in the mating pocket and push into the grease. The grease will hold the segment in place when the jaw is turned over to replace.
- Page 9 Maintenance Schedule It is very important to perform regularly maintenance on your Kurt vise to assure proper operation. Improper maintenance will result in poor vise performance and may void your warranty. Daily/ Weekly 1. Remove chips from surface of vise.