Related Manuals for Kurt D688 AngLock Vise Base Assembly
Summary of Contents for Kurt D688 AngLock Vise Base Assembly
- Page 1 D688 AngLock Vise ® ® Base Assembly Operating Instructions Manual Manual de instrucciones de operación ENGLISH ESPAÑOL...
-
Page 2: Table Of Contents
Table of Contents Introduction .........................3 Setup Instructions ......................4 Operating Instructions ..................5-7 D688 Parts List ......................8 D688 Mechanical Drawing ..................9 Maintenance Schedule ..................10-12 Troubleshooting Tips ..................... 13 CAUTION: Is used when your action or lack of action may cause serious injury. Vise Data Use this to fill out information about your vise for quick reference. -
Page 3: Introduction
Introduction Thank you for purchasing a Kurt vise. You have just purchased one of the best machine vises in the industry. The D-Series AngLock vise has a time proven design. The outstanding accuracy of this product is second to none. Backed by a lifetime warranty, this product will last forever when used and maintained properly. -
Page 4: Setup Instructions
Set-up Instructions Now that you have your new Kurt Vise, it’s time to set-up and begin using it. You will see that your new vise comes with a Kurt swivel handle, chip guard and instruction manual in the shipping carton. The chip guard rests between the ways of the vise and can be trimmed to size to help keep the chips out of the screw. -
Page 5: Operating Instructions
If you need more clamping force you may require a larger vise. To properly clamp a part in your Kurt vise you should place the part in the center of the jaws resting on the ways of the vise. Clamping only on one side or above the movable and stationary jaws can result in jaw lift or loss of accuracy. - Page 6 Fig.1 Sketch #2A Incorrect part clamping. Vise width centerline Sketch #2B Correct part clamping. Sketch #2C Correct part clamping. Sketch #2D Correct part clamping. Non- machined spacer ENGLISH | Operating Instructions...
- Page 7 Proper O-Ring installation and usage Most jobs require a tight contact between the workpiece and the parallels (see above). This option offered by Kurt Manufacturing Company is ideal for that. The O-Ring installation will provide for the movement needed when working with parallels.
-
Page 8: D688 Parts List
Thrust Bearing Washer *D675-217A Spiral Retaining Ring *D60-41 Thrust Bearing D688-102 I.D. Tag 07-0230 U-Type Drive Screw D675-111 Kurt Logo Label 225-20 O-Ring, Polyurethane #00 Dl600-249 Chip Guard (LONG) D60I-10A-SA Handle Assembly D60-72 Thrust Bearing Assembly *D688-KIT Includes. ENGLISH | D688 Parts List... -
Page 9: D688 Mechanical Drawing
D688 Mechanical Drawing | ENLGISH D688 Mechanical Drawing... -
Page 10: Maintenance Schedule
Maintenance Schedule It is very important to perform regularly maintenance on your Kurt vise to assure proper operation. Improper maintenance will result in poor vise performance and may void your warranty. Daily/ Weekly 1. Remove chips from surface of vise. - Page 11 8. Tighten the setscrew to firmly contact the nut. Back off the setscrew ¼ turn (approx.) note: DO NOT leave the setscrew tightened firmly to the nut as this may cause improper operation. The movable jaw is designed to move slightly (pivot side to side) so maximum jaw plate contact is maintained when clamping out- of-parallel, sawed, or cast parts.
- Page 12 3 to 6 months 1. Open vise to maximum opening. 2. Remove spiral snap ring and washer from hex end of the vise screw. 3. Slide the movable jaw toward the stationary. 4. Remove the thrust bearing assembly consisting of (2) thrust washers and (1) thrust bearing from the counter bore in the end of the body.
-
Page 13: Troubleshooting Tips
Troubleshooting Tips The Kurt D-Series vise will operate mostly trouble free for many years. If properly maintained, this product is indestructible. In some cases it will be necessary to troubleshoot. Use the information below to help in the process. Problem: My vise turns hard. - Page 14 Maintenance Log/Notes: ENGLISH | Maintenance Log/Notes...
- Page 15 Thank you for your purchase! If you have any feedback or questions. Please contact us at: workholding@kurt.com 1-877-226-7823 Like, Tweet, and Subscribe to us!
- Page 16 The sole obligation of Kurt Manufacturing Company, Inc. (Kurt) and the purchaser’s SOLE AND EXCLUSIVE REMEDY hereunder, shall be limited to the replacement or repair of any Kurt product or part (by an authorized Kurt technician) which are returned to Kurt Manufacturing Company’s place of business, transportation, shipping and postal charges prepaid, and there determined by Kurt Manufacturing Company to be covered by the warranty contained herein.
- Page 17 Prensa D688 AngLock ® ® Ensamble de Base Manual de instrucciones de operación ESPAÑOL...
- Page 18 Tabla de contenido Introducción ......................19 Instrucciones de instalación ................20 Instrucciones de operación ................21-23 D688 Lista De Piezas ....................24 D688 Dibujo Mecánico ..................25 Programa de mantenimiento ...............26-28 Sugerencias para la resolución de problemas ..........29 PRECAUCIÓN: Se utiliza cuando la acción o falta de acción puede causar lesiones graves.
- Page 19 Introducción Muchas gracias por comprar una prensa Kurt. Usted ha comprado una de las mejores prensas para mecanizado de la industria. La prensa AngLock™ Serie D tiene un diseño ampliamente comprobado. La extraordinaria exactitud de este producto es insuperable. Con el respaldo de una garantía de por vida, este producto durará...
- Page 20 Instrucciones de instalación Ahora que ya tiene su nueva prensa Kurt Serie D, es el momento de comenzar a utilizarla. Usted verá que su nueva prensa viene con una manija giratoria Kurt y un manual de instrucciones suministrados en la caja de envío. La manija está diseñada específicamente para proporcionar el máximo par de torsión a su prensa.