Manual Timer Programming - JVC DR-MV1S Instructions Manual

OPERATIONS ON DVD DECK
44
EN

Manual Timer Programming

You can programme this unit to timer-record as many as
8 programmes.
If you do not know the S
HOW
wish to record, use the following procedure to set your unit to
timer-record the programme.
● Make sure that the unit's built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
DVD TIMER (#)
VCR/DVD
PROG/CHECK
ENTER
1
Load a recordable disc.
2
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3
Press PROG/CHECK to
access the Programme Check
screen.
● When "PROGRAMME FULL
DELETE UNWANTED TIMER
PROGRAMME" appears on the
TV screen, you need to cancel
some of the reserved
programmes. ( pg. 47)
4
Press rt to select "NEW
TIMER PROGRAMME", then
press ENTER. The programme
screen appears.
5
Press rt to set the desired
date.
● The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press w e to select "START", then press rt to set the desired
start time.
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press w e to select "STOP", then press rt to set the desired
stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press w e to select "TV PROG", then press rt to select the
desired channel.
9
Set the other recording options as required.
● Refer to step 6 in "S
V
HOW IEW
V number for the programme you
IEW
SAT
1 2 3
4 5 6
7 8 9
AUX
0
DISPLAY
rtw e
TM Timer Programming" ( pg. 43).
10
Press ENTER to access the Programme Confirmation screen.
11
Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 11.
12
Press DVD TIMER (#) to engage the unit's timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. Press 1 to turn off the unit. When the
VCR deck is in timer standby mode, the unit is automatically turned
off.
● To disengage the timer mode, press DVD TIMER (#) again.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform "Satellite Receiver Control Setting (DVD Deck Only)"
( pg. 21).
B Perform "Manual Timer Programming" (
press AUX to change "TV PROG" to "SAT". Then press rt to
enter the channel position for the satellite broadcast. In step 9,
you cannot set "VPS/PDC" to "ON".
C Leave the satellite receiver's power on.
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your video unit and
have precedence over the advertised times you may have preset
into the timer. This means that your unit will start and stop
recording when the preset TV programmes actually start and end
— even if the broadcast time of a preset TV programme is
changed.
NOTES:
● When you use Manual Timer Programming, set the start time (VPS
or PDC time) exactly as advertised in the TV listing. A different time
than advertised will result in no recording.
● VPS/PDC recording is also possible when a satellite receiver or a
cable system is connected to L-2 IN/DECODER connector on your
unit.
● VPS/PDC recording is also possible via the L-1 IN/OUT connector.
How to check if the station being received transmits a VPS/
PDC signal
A Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
B Hold down DISPLAY for about 5 seconds. "VPS/PDC" appears
blinking on the front display panel. If a VPS/PDC signal is detected
from the station, "VPS/PDC" will stop blinking. If no VPS/PDC
signal is detected from the station, "VPS/PDC" will blink at a slower
rate.
C Press DISPLAY again to return to normal display.
pg. 44). In step 8,