Raymarine RAY50 Installation And Operation Instructions Manual page 9

European licensing requirements
Regulations in some areas require that an Operator's
license is obtained before operating a VHF radio.
It is your responsibility to determine whether a
license is required in your area before operating this
equipment.
Additional information – Ray50
The following additional information is required for
completing a license application in Canada and the
US.
Industry Canada 4069B-RAY50D
certification number
FCC ID PJ5–RAY50
FCC Type accepted Parts 2, 15 and 80
Output power 1 watt (low) and 25 watt (high)
Modulation FM
Frequency range 155.500 MHz to 163.275 MHz
Additional information – Ray60
The following additional information is required for
completing a license application in Canada and the
US.
Industry Canada 4069B-RAY60D
certification number
FCC ID PJ5–RAY60
FCC Type accepted Parts 2, 15 and 80
Output power 1 watt (low) and 25 watt (high)
Modulation FM
Frequency range 155.500 MHz to 163.275 MHz
Additional information – Ray70
The following additional information is required for
completing a license application in Canada and the
US.
Industry Canada 4069B-RAY70D
certification number
FCC ID PJ5–RAY70
FCC Type accepted Parts 2, 15 and 80
Output power 1 watt (low) and 25 watt (high)
Modulation FM
Frequency range 155.500 MHz to 163.275 MHz
Maritime Mobile Service Identity (MMSI)
This product is a class "D" Digital Selective Calling
(DSC) device.
A 9 digit MMSI number is required to operate DSC
equipment. In some areas, a radio operator license
is required before an MMSI number can be issued.
Note: You can request an MMSI number from
the same agency that issues radio or ship radio
licenses in your area. Once obtained, you can
program the MMSI number into your product by
following the instruction supplied with the product.
Important information
Once obtained, you can program the MMSI number
into your product using the instructions provided.
If regulations in your area do not permit you to
program the MMSI number yourself, your Raymarine
dealer can program the number for you.
Obtaining an MMSI number in the United States
You can request an MMSI number from the FCC
when you apply for a Station License. If your vessel
does not require a license, you may obtain an MMSI
by contacting BoatUS www.boatus.com.
Obtaining an MMSI number in Canada
You can obtain an MMSI number from your nearest
Industry Canada Office.
Obtaining an MMSI number in Europe and rest
of world
Am MMSI number should be requested from the
same agency that issues radio operator licenses in
your area.
Automatic Transmitter Identification System
(ATIS)
Your product includes ATIS functionality for
use on the inland waterways of contracting
governments of the "Regional Arrangement on the
Radiocommunication Service for Inland Waterways"
— also known as "RAINWAT".
ATIS adds data at the end of radio transmissions that
identifies your station. ATIS operation can be turned
on or off as needed via the radio's menu.
An ATIS ID can be obtained from the same agency
that issues radio operator licenses in your area.
Your ATIS ID should be programed into your product
using the instructions provided.
Note: Contracting RAINWAT countries include:
Austria, Belgium, Bulgaria, Croatia, the
Czech Republic, France, Germany, Hungary,
Luxembourg, Moldova, Montenegro, the
Netherlands, Poland, Romania, Serbia, the Slovak
Republic and Switzerland.
Note: When ATIS is enabled, certain programing
steps have been implemented to protect the
integrity of the RAINWAT agreement, including the
blocking of DSC functions when ATIS is enabled.
EMC installation guidelines
Raymarine equipment and accessories conform to
the appropriate Electromagnetic Compatibility (EMC)
regulations, to minimize electromagnetic interference
between equipment and minimize the effect such
interference could have on the performance of your
system
Correct installation is required to ensure that EMC
performance is not compromised.
Note: In areas of extreme EMC interference,
some slight interference may be noticed on the
product. Where this occurs the product and the
source of the interference should be separated by
a greater distance.
9