Page 1 Ray50 / Ray60 / Ray70 Installation and operation instructions Date: 03-2015 Document number: 81356-1-EN © 2015 Raymarine UK Limited...
Page 3 Trademark and patents notice Raymarine, Tacktick, Clear Pulse, Truzoom, HSB, SeaTalk, SeaTalk , SeaTalk , Micronet, Raytech, Gear Up, Marine Shield, Seahawk, Autohelm, Automagic, and Visionality are registered or claimed trademarks of Raymarine Belgium. FLIR, DownVision, SideVision, Dragonfly, Instalert, Infrared Everywhere, and The World’s Sixth Sense are registered or claimed trademarks of FLIR Systems, Inc.
Page 5: Table Of Contents
............... 54 3.1 Installation checklist ..........16 6.18 GPS/GNSS setup..........55 3.2 Parts supplied – Ray50 ........16 6.19 Station priority - Ray60 and Ray70...... 56 3.3 Parts supplied – Ray60 / Ray70......17 3.4 Software updates ..........17 Chapter 7 Digital selective calling (DSC)...
Page 6 12.2 Viewing product information ........ 90 12.3 Learning resources..........91 Chapter 13 Technical specification....93 13.1 Technical specification — Ray50 ......94 13.2 Technical specification — Ray60 ......95 13.3 Technical specification — Ray70 ......96 13.4 Radio usage ............97 Chapter 14 Spares and accessories ....
Page 7: Chapter 1 Important Information
Raymarine approved installer. A certified installation qualifies for enhanced product warranty benefits. Warning: Maximum Permissible Contact your Raymarine dealer for further details, Exposure and refer to the separate warranty document packed with your product. Failure to observe these guidelines...
Page 8: General Information
This Class B digital apparatus complies with Canadian ICES-003. Disclaimer Raymarine does not warrant that this product is Licensing error-free or that it is compatible with products Prior to using this product please check your national...
Page 9 If regulations in your area do not permit you to license is obtained before operating a VHF radio. program the MMSI number yourself, your Raymarine It is your responsibility to determine whether a dealer can program the number for you.
Page 10 A radar beam can normally be assumed electrical and electronic equipment. Whilst the to spread 20 degrees above and below the WEEE Directive does not apply to some Raymarine radiating element. products, we support its policy and ask you to be •...
Page 11: Chapter 2 Document And Product Information
Chapter 2: Document and product information Chapter contents • 2.1 Document information on page 12 • 2.2 Product information on page 13 Document and product information...
Page 12: Document Information
2.1 Document information Document conventions The following conventions are used throughout this This document contains important information document when referring to: related to the installation of your Raymarine product. Type Example Convention The document includes information to help you: Procedures for Select Set-Up.
Page 13: Product Information
2.2 Product information Product documentation The following documentation is applicable to your The Ray50, Ray60 and Ray70 are 12 V dc, Class product: D Digital Selective Calling (DSC) VHF radios. DSC enables you to make a selective call to a...
Page 14 Ray50 / Ray60 / Ray70...
Page 15: Chapter 3 Planning The Installation
Chapter 3: Planning the installation Chapter contents • 3.1 Installation checklist on page 16 • 3.2 Parts supplied – Ray50 on page 16 • 3.3 Parts supplied – Ray60 / Ray70 on page 17 • 3.4 Software updates on page 17 •...
Page 16: Installation Checklist
3.1 Installation checklist 3.2 Parts supplied – Ray50 Installation includes the following activities: The parts listed below are supplied with the Ray50 Installation Task Plan your system. Obtain all required equipment and tools. Site all equipment. Route all cables. Drill cable and mounting holes.
Page 17: Parts Supplied - Ray60 / Ray70
The parts listed below are supplied with the Ray60 The software running on the product can be updated. and Ray70. • Raymarine periodically releases software updates to improve product performance and add new features. • You can update the software for your product using a connected and compatible multifunction display.
Page 18: Tools Required For Installation
5. 7 mm (9/32”) Wrench (spanner) for bracket mounting fixings 6. File for panel mount cut out 7. Hole saw for panel mounting (For hole saw size refer to your product’s mounting template) 8. Drill bit for surface mounting or bracket mounting Ray50 / Ray60 / Ray70...
Page 19: System Integration - Ray50
3.6 System integration — Ray50 Your VHF radio can be connected to the following marine electronics devices. D13294-1 Maximum Item Device type quantity Suitable devices Connections Passive speaker 3rd party 5 W (4 Ω) / 2.5 W (8 Ω) RCA audio connector...
Page 20: System Integration - Ray60 / Ray70
• e Series • gS Series • C-Series Widescreen • E-Series Widescreen • G-Series system GPS Receiver 1 active • RS130 SeaTalk ng® / NMEA 2000 • RS125 • Raymarine multifunction display equipped with internal GPS Ray50 / Ray60 / Ray70...
Page 21: System Protocols
3.8 System protocols passed in ‘sentences’, each of which has a three letter sentence identifier. It is therefore important Your product can send and receive position when checking compatibility between items that the information, e.g. latitude and longitude using any of same sentence identifiers are used some examples the following protocols: of which are:...
Page 22: General Location Requirements
Cable routing requirements Ensure the unit is mounted in a location which allows proper routing and connection of cables: • Minimum cable bend radius of 100 mm (3.94 in) is required unless otherwise stated. Ray50 / Ray60 / Ray70...
Page 23: Mounting Options
3.10 Mounting options • Use cable supports to prevent stress on connectors. The product can be mounted in the following configurations. Electrical interference Select a location that is far enough away from devices that may cause interference, such as motors, generators and radio transmitters/receivers. Power supply Select a location that is as close as possible to the vessel’s DC power supply.
Page 24: Product Dimensions
3.11 Product dimensions Ray60 and Ray70 dimensions (bracket mount) Ray50 product dimensions The Ray50 can be panel mounted or bracket mounted. Ray50 dimensions (panel mount) 168 mm (6.6 in.) 226 mm (8.9 in 156 mm (6.1 in.) 25 mm (1 in . ) 39.75 mm (1.6 in.)
Page 25 The Handset’s fitted, coiled lead can be extended comfortably to approximately 1 meter (3.3 ft.) Planning the installation...
Page 26 Ray50 / Ray60 / Ray70...
Page 27: Chapter 4 Cables And Connections
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 28 • 4.2 Connections overview - Ray50 on page 29 • 4.3 Connections overview Ray60 / Ray70 on page 29 • 4.4 Power connection on page 30 •...
Page 28: General Cabling Guidance
Ensure that all data cables are properly shielded that the cable shielding is intact (e.g. hasn’t been • Ensure that any non-Raymarine cables are of the scraped off by being squeezed through a tight area). correct quality and gauge. For example, longer...
Page 29: Connections Overview - Ray50
4.2 Connections overview - Ray50 4.3 Connections overview Ray60 / Ray70 The following connections are available on the Ray50. The following connections are available on the Ray60 and Ray70. D13296-1 1. Ground point — DO NOT USE! D13297-1 2. SeaTalk ng®...
Page 30: Power Connection
Raymarine authorized dealer for support. connection. Ray50 / Ray60 / Ray70...
Page 31: Connecting Handsets And Cables
4.5 Connecting handsets and cables Sharing a breaker Where more than 1 piece of equipment shares a Follow the steps below to connect handsets and breaker you must provide protection for the individual extension cables together. circuits. E.g. by connecting an in-line fuse for each 1.
Page 32: Fistmic Connection Ray60 / Ray70
2. Fully insert the connector into the connector on the front of the unit. 3. Rotate the locking collar clockwise until it clicks. D13299-1 1. Base station 2. Fistmic 3. Raymic handset extension cable (A80291) 4. Fistmic adaptor cable (A80296) Ray50 / Ray60 / Ray70...
Page 33: Seatalk Ng® Connection
2. Ensure the spur cable connector is correctly SeaTalk orientated. D13293-1 3. Fully insert the spur cable connector into the 1. Ray50 / Ray60 / Ray70 SeaTalk ng® connector on the unit. 2. Optional Raymic handset station (Ray70 and 4. Rotate the locking collar clockwise 2 clicks, to Ray70 only) the locked position.
Page 34: Nmea 0183 Connection
5. Push the protective boot over the connection. 6. Secure the protective boot using the supplied cable ties. If the antenna connector cannot be removed then another suitable means of protection must be used, such as electrical tape. Ray50 / Ray60 / Ray70...
Page 35: Second Handset Station - Ray60 / Ray70
4.10 Second handset station — Ray60 4.11 Passive speaker connection / Ray70 A passive speaker can be connected using the RCA lead on the radio or on the handset adaptor cable. The Raymic handset accessory can be connected to the second station connector located on the rear of the radio, this will create a second fully functional station.
Page 36: Loud Hailer Connection
A single loud hailer can be connected to the radio using the dedicated loud hailer wires. D13219-1 (+) Hailer wire (Purple) (-) Hailer wire (Gray) Loud hailer wires should be connected securely and covered to prevent corrosion. Ray50 / Ray60 / Ray70...
Page 37: Chapter 5 Location And Mounting
Chapter 5: Location and mounting Chapter contents • 5.1 Bracket mounting on page 38 • 5.2 Ray50 Panel mounting on page 38 • 5.3 Ray60 / Ray70 Panel mounting on page 40 • 5.4 Fistmic / Handset mounting on page 41 •...
Page 38: Bracket Mounting
Panel mounting the Ray50 To panel mount the Ray50 follow the steps below. Before mounting the product, ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling / cutting.
Page 39 Note: The supplied gasket provides a seal between the unit and a suitably flat and stiff mounting surface or binnacle. The gasket should always be used. It may also be necessary to use a marine-grade sealant if the mounting surface or binnacle is not entirely flat and stiff or has a rough surface finish.
Page 40: Ray60 / Ray70 Panel Mounting
Inner edges - ensure that the bezel sits flat. is required. 4. Check that all control buttons are free to operate. 2. Fix the supplied mounting template to the selected location, using masking or self-adhesive tape. Ray50 / Ray60 / Ray70...
Page 41: Fistmic / Handset Mounting
5.4 Fistmic / Handset mounting 5.5 Ray60 / Ray70 Raymic handset cradle mounting The Fistmic and optional Handset can be mounted by following the steps below. Whilst only the Fistmic Before mounting the unit, ensure that you have: is pictured below the steps are identical when •...
Page 42: Pass-Through Panel Kit Mounting
11. Connect the opposite end of the cable to the required connector either on the base station or to another pass-through panel mounting plate connector. Ray50 / Ray60 / Ray70...
Page 43: Chapter 6 Getting Started
Chapter 6: Getting started Chapter contents • 6.1 Controls and interface on page 44 • 6.2 Powering the unit on on page 44 • 6.3 Powering the unit off on page 45 • 6.4 Homescreen overview on page 45 • 6.5 Shortcut list on page 47 •...
Page 44: Controls And Interface
4. Channel Up and Down — Changes the channel up or down. 5. HI/LO — Press to switch between High (25 W) and low (1 W) transmit power. 6. 16 / PLUS — When powered on press to switch between priority channels. Ray50 / Ray60 / Ray70...
Page 45: Powering The Unit Off
6.3 Powering the unit off 6.4 Homescreen overview The information below describes the on-screen With the unit powered on: characters and symbols which the radio displays on 1. Press and hold the Power button for the main screen and what they mean. approximately 3 seconds to power the unit off.
Page 46: Main Menu Overview
• 2nd priority below the specified channel operating voltage * Weather Mode • Weather Homescreen Power supply Indicates the power voltage too high supply to the radio is above the specified operating voltage Ray50 / Ray60 / Ray70...
Page 47: Shortcut List
6.5 Shortcut list Symbol Name Sub-options * Scan Mode • All channels Pressing the Power button once while the radio is switched on will open the Shortcuts list. The • All channels + 16 Shortcuts list can be used to adjust the brightness, •...
Page 48: Initial Startup
6. Frequency band selection Sets the relevant channels for your region. This step is not applicable if the radio has been pre-programed in MARCOM-C mode. See 6.14 Changing the radio region for more information. Ray50 / Ray60 / Ray70...
Page 49: Selecting A Language
6.8 Selecting a language 6.9 Switching on the AIS receiver — Ray70 The language the radio uses can be changed. The Ray70’s AIS receiver can be switched on or off. From the Main menu: 1. Select Set-up. From the Main menu: 2.
Page 50: Selecting A Network Type
Move cursor back and forward through the digits. 7. When the final digit is confirmed select DONE. Example Enter MMSI number Done 8. The MMSI is displayed onscreen, check that it is correct, then: i. Select Yes – Save, or Ray50 / Ray60 / Ray70...
Page 51: Enabling And Disabling Atis Mode
ATIS ID once! From the Main menu. If you store an incorrect MMSI number 1. Select Set-up. or ATIS ID in your product, it will have to be reset by an authorized Raymarine ® 2. Select ATIS set-up. dealer. 3. Select ATIS.
Page 52: Entering Your Atis Id
You can only enter the MMSI number and ATIS ID once! If you store an incorrect MMSI number or ATIS ID in your product, it will have to ® be reset by an authorized Raymarine dealer. D13225-1 From the Main menu. 1. Select Set-up.
Page 53: Changing The Radio Region
6.14 Changing the radio region 6.15 Adjusting the display brightness Prior to using the radio you must set the Frequency The display’s brightness level can be adjusted by band to the region your radio will be used in. following the steps below. From the Main menu: From the Display set-up menu: Menu >...
Page 54: Adjusting The Display Contrast
2. Use the Rotary knob to adjust the display’s 1. Select Power output. contrast to the required level. 2. Select Low for 1 W transmit power, or 3. Select High for 25 W transmit power. Ray50 / Ray60 / Ray70...
Page 55: Gps/Gnss Setup
DSC distress transmissions. The Homescreen display option is also available Position data received from other vessels can be from the Display set-up menu displayed on a connected Raymarine ® multifunction display. Setting time format and offset...
Page 56: Station Priority - Ray60 And Ray70
PTT button. • The Local station will retain control for 3 seconds after the last button press. • The information on the station which has control is repeated on the other station’s display. Ray50 / Ray60 / Ray70...
Page 57: Chapter 7 Digital Selective Calling (Dsc)
Chapter 7: Digital selective calling (DSC) Chapter contents • 7.1 Digital Selective Calling (DSC) on page 58 • 7.2 Distress calls on page 59 • 7.3 Urgency calls on page 61 • 7.4 Safety calls on page 62 • 7.5 Individual (routine) calls on page 62 •...
Page 58: Digital Selective Calling (Dsc)
• Vessel MMSI number. • Vessel position (must be input manually if no GPS position data is available). • Local time (must be input manually if no GPS position data is available). • Transmission frequency. Ray50 / Ray60 / Ray70...
Page 59: Distress Calls
7.2 Distress calls down reaches zero the DSC distress call is transmitted. Making a designated distress call The distress call is repeated automatically until it When making a Distress call you can specify the is acknowledged. nature of the distress, if GPS data is not available 2.
Page 60 When a distress call is received an alarm is sounded at full volume and the LCD displays information This is <MMSI of your vessel>, <name of your relating to the distress. vessel repeated 3 times> <call sign of your vessel> RECEIVED MAYDAY Ray50 / Ray60 / Ray70...
Page 61: Urgency Calls
7.3 Urgency calls 4. You MUST then notify the shore authorities by any means possible to relay the distress call. Making an urgency call Manually relaying a distress call An urgency call should be used when there is A distress relay should only be sent if: the person or danger to a vehicle or person that does not require vehicle in distress is unable to transmit the distress immediate assistance.
Page 62: Safety Calls
2. Select Reply on Ch ## at any time to accept the call. If auto channel change is turned on then the channel will automatically change after 10 seconds. The radio is re-tuned to the specified channel. 3. To reject the call, select Reject. Ray50 / Ray60 / Ray70...
Page 63: Group Calls
7.6 Group calls 4. If you rejected the call, select a reason for the rejection from the list. Group calls can be made to groups of vessels Confirmation of the acceptance or rejection of the sharing the same Group MMSI numbers. call is displayed.
Page 64: Position Requests
OK button again to save the changes. Deleting a phonebook entry From the DSC Calls menu: Menu > DSC Calls. 1. Select Phonebook. 2. Select the contact you want to edit. 3. Select Delete. 4. Select Yes. The contact is deleted. Ray50 / Ray60 / Ray70...
Page 65: Call Logs
70 to another DSC VHF radio. • MMSI number(s) (If a call is relayed up to 3 MMSI Raymarine recommends that once you've numbers can be recorded.) successfully placed a test call you add the test call •...
Page 66: Dsc Set-Up Menu Options
DSC calls are received. Position requests With Position • Auto requests set accept (default) to Auto accept • Manual accept the radio will automatically send out position details when a position request is received. Ray50 / Ray60 / Ray70...
Page 67: Chapter 8 Vhf Operations
Chapter 8: VHF operations Chapter contents • 8.1 Watch modes on page 68 • 8.2 Scan Mode on page 68 • 8.3 Priority channels on page 69 • 8.4 Sensitivity on page 69 • 8.5 Private channels on page 70 •...
Page 68: Watch Modes
2. Select Edit Saved Channels to select the channels that will be scanned when performing a Saved channel scan. 3. During Scan mode, press the Back button at any time to end the Scan mode and resume normal operation. Ray50 / Ray60 / Ray70...
Page 69: Priority Channels
8.3 Priority channels 8.4 Sensitivity Channel 16 is the dedicated priority channel. The sensitivity level of the radio can be set to Local mode or Distant mode. The default secondary priority channel is channel 09. If your frequency band is set to INT (international) Local mode decreases the receiver sensitivity in then the second priority channel can be changed.
Page 70: Private Channels
2. Select the required private channel set. operation. Marcom-C operation is set by the dealer at point of sale. If you wish to enable or disable Marcom-C mode, you must contact your Raymarine dealer. For further information please contact Raymarine technical support.
Page 71: Ais - Ray70
8.7 AIS — Ray70 The Ray70 has a built in AIS receiver. With the built-in AIS receiver switched on AIS information can be sent to a connected Raymarine ® MFD using either NMEA 0183 or SeaTalk ng® Note: If using the built-in AIS receiver and outputting over NMEA 0183, ensure that the baud rate is set to 0183 High speed: Menu >...
Page 72: Set-Up Menu Options
• Off (default) internal AIS receiver on and off. • On Network output Enables you to select the network to be • NMEA 2000 used to output data. • 0183 High speed • 0183 Std speed Ray50 / Ray60 / Ray70...
Page 73 Menu Description Options ATIS set-up Enables you to switch ATIS mode on and • ATIS off and enter your ATIS ID. • ATIS ID Maintenance Enables you to view system details and • About this unit functions that may be required during •...
Page 74 Ray50 / Ray60 / Ray70...
Page 75: Chapter 9 Hailer, Fog Horn, And Intercom
Chapter 9: Hailer, Fog horn, and Intercom Chapter contents • 9.1 Hailer Fog Intercom menu on page 76 • 9.2 Loud Hailer — Ray70 on page 76 • 9.3 Fog horn on page 77 • 9.4 Intercom — Ray60 and Ray70 on page 77 Hailer, Fog horn, and Intercom...
Page 76: Hailer Fog Intercom Menu
6. The hailer listening volume can be adjusted at any time in Listening mode using the Volume Control. 7. The hailer talking volume can be adjusted at any time, with the PTT button pressed using the Volume Control. Ray50 / Ray60 / Ray70...
Page 77: Fog Horn
9.3 Fog horn 9.4 Intercom — Ray60 and Ray70 The fog horn function requires an optional loud hailer The Intercom function is available when a second to be connected. station is connected to your radio. The fog horn function can be set to manual or to a The intercom function allows voice communication predefined automatic mode between the second (handset) station and the...
Page 78 Ray50 / Ray60 / Ray70...
Page 79: Chapter 10 Maintenance
Chapter 10: Maintenance Chapter contents • 10.1 Maintenance on page 80 • 10.2 Routine checks on page 80 • 10.3 Product cleaning on page 81 • 10.4 Unit cleaning instructions on page 81 Maintenance...
Page 80: Maintenance
Note: Cable checks should be carried out with the • If you remove a handset connection ensure the power supply switched off. dust cap is fitted to the connector. Ray50 / Ray60 / Ray70...
Page 81: Product Cleaning
10.3 Product cleaning 10.4 Unit cleaning instructions Best cleaning practices. The unit does not require regular cleaning. However, if you find it necessary to clean the unit, please follow When cleaning products: the steps below: • If your product includes a display screen, do NOT 1.
Page 82 Ray50 / Ray60 / Ray70...
Page 83: Chapter 11 Troubleshooting
Chapter 11: Troubleshooting Chapter contents • 11.1 Troubleshooting on page 84 • 11.2 Performing a system reset on page 84 • 11.3 System test on page 85 • 11.4 Power up troubleshooting on page 86 • 11.5 VHF Radio troubleshooting on page 87 •...
Page 84: Troubleshooting
From the Maintenance menu: Menu > Set-up > installations. Maintenance. All Raymarine products are, prior to packing and 1. Select System reset. shipping, subjected to comprehensive test and quality assurance programs. However, if you 2. Select Yes.
Page 85: System Test
11.3 System test The system test menu can be used to show the status of the system and connected devices. The System test menu show the status of the following system components and connected devices: • GPS • DSC • Battery •...
Page 86: Power Up Troubleshooting
See possible solutions from ‘Products does not turn on or keeps turning off’ above. Software corruption In the unlikely event that the products software has become corrupted please try re-flashing the latest software from the Raymarine website. Ray50 / Ray60 / Ray70...
Page 87: Vhf Radio Troubleshooting
11.5 VHF Radio troubleshooting Problems with your VHF radio and their possible causes and solutions are described below: DSC functions are not available / working MMSI number not programmed. Programme your MMSI number. Radio is set to ATIS or Marcom-C mode. Use of DSC is not permitted when in ATIS or Marcom-C mode.
Page 88: Gps Troubleshooting
Problems with the GPS/GNSS and their possible causes and solutions are described below. Before troubleshooting GPS problems ensure your product has the latest software, by checking the Software Updates page on the Raymarine website www.raymarine.com. No GPS fix Possible causes...
Page 89: Chapter 12 Technical Support
Chapter 12: Technical support Chapter contents • 12.1 Raymarine customer support on page 90 • 12.2 Viewing product information on page 90 • 12.3 Learning resources on page 91 Technical support...
Page 90: Raymarine Customer Support
Product information can be found on the Startup support service. You can contact customer support screen. through the Raymarine website, telephone and 1. Power up the radio. e-mail. If you are unable to resolve a problem, please The startup screen is displayed which shows the use any of these facilities to obtain additional help.
Page 91: Learning Resources
Internet connection. • Some videos are only available in English. Training courses Raymarine regularly runs a range of in-depth training courses to help you make the most of your products. Visit the Training section of the Raymarine website for more information: •...
Page 92 Ray50 / Ray60 / Ray70...
Page 93: Chapter 13 Technical Specification
Chapter 13: Technical specification Chapter contents • 13.1 Technical specification — Ray50 on page 94 • 13.2 Technical specification — Ray60 on page 95 • 13.3 Technical specification — Ray70 on page 96 • 13.4 Radio usage on page 97...
Page 94: Technical Specification - Ray50
13.1 Technical specification — Ray50 Receiver sensitivity • Distance — 119dBm (0.25uV) @ 12dB SINAD (typical) Environmental specification • Local — 110dBm (0.7uV) @ 12dB Operating temperature -20ºC (-4ºF) to +60ºC (140ºF) SINAD (typical) Storage temperature -25ºC (-13ºF) to +70ºC (158ºF)
Page 95: Technical Specification - Ray60
13.2 Technical specification — Ray60 Receiver sensitivity • Distance — 119dBm (0.25uV) @ 12dB SINAD (typical) Environmental specification • Local — 110dBm (0.7uV) @ 12dB Operating temperature -20ºC (-4ºF) to +60ºC (140ºF) SINAD (typical) Storage temperature -25ºC (-13ºF) to +70ºC (158ºF) Adjacent channel More than 70 dB selectivity...
Page 96: Technical Specification - Ray70
(Private channels) Geodetic Datum WGS-84 (alternatives available through Raymarine MFD) Sensitivity Better than 1 microvolt EMF @ 20dB SINAD Refresh Rate 10 Hz (10 times per second Concurrent GNSS) Squelch sensitivity Less than —2 dBµ EMF Ray50 / Ray60 / Ray70...
Page 97: Radio Usage
13.4 Radio usage Antenna • Internal — Ceramic chip mounted near top of unit The radio can be used worldwide, including the Position Accuracy • Without SBAS: <= 15 metres 95% following European countries: of the time • With SBAS: <= 5 metres 95% of the time Technical specification...
Page 98 Ray50 / Ray60 / Ray70...
Page 99: Chapter 14 Spares And Accessories
Chapter 14: Spares and accessories Chapter contents • 14.1 Spares on page 100 • 14.2 Accessories — Ray60 / Ray70 on page 100 • 14.3 SeaTalk cables and accessories on page 101 Spares and accessories...
Page 100: Spares
Ray70 Panel seal R70435 Ray50 (black screw covers) / Ray60 / Ray70(Gunmetal bezel) kit Ray50 sun cover R70437 Ray60 / Ray70 R70436 sun cover Panel mount R70438 fixings kit Ray60 / Ray70 A80301 Raymic handset cradle Ray50 / Ray60 / Ray70...
Page 101: Seatalk Ng Cables And Accessories
14.3 SeaTalk cables and accessories Description Part No Notes SeaTalk cables and accessories for use with SeaTalk Power A06049 compatible products. cable Description Part No Notes SeaTalk A06031 Terminator SeaTalk starter kit T70134 Includes: SeaTalk T-piece A06028 Provides 1 x spur •...
Page 102 Ray50 / Ray60 / Ray70...
Page 103: Appendix A Nmea 0183 Sentences
Appendix A NMEA 0183 sentences The radio supports the following NMEA 0183 sentences. Ray50 / Ray60 Ray70 Sentence Description Receive Transmit Receive Transmit ● ● Digital Selective Calling ● ● Expanded Digital Selective Calling ● AIS VHF Data Link Message ●...
Page 104: Appendix B Nmea 2000 Pgn List
● 129802 AIS Safety Related Broadcast Message ● ● 129808 DSC Call Information ● 129809 AIS Class B “CS” Static Data Report, Part A ● 129810 AIS Class B “CS” Static Data Report, Part B Ray50 / Ray60 / Ray70...
Page 105: Appendix C Vhf Channels
Appendix C VHF Channels US Marine VHF Channels and Frequencies CH No. TX Freq RX Freq Single Freq Use 156.050 156.050 Port operations and commercial, VTS. Available only in New Orleans / Lower Mississippi area. 156.150 156.150 US Government only. 156.250 156.250 Port operations or VTS in the Houston, New Orleans and Seattle areas.
Page 106 5. Channel 17 and channel 77 have a fixed power output of 1 watt. 6. Channel 13 and channel 67 have an initial power output of 1 watt. User can temporarily override this restrictions to transmit at high power. Ray50 / Ray60 / Ray70...
Page 107 Canadian Marine VHF Channels and Frequencies Area of CH No. TX Freq RX Freq operation 156.050 160.650 Public correspondence. 156.100 160.700 Public correspondence. 156.150 160.750 Public correspondence. 156.200 156.200 Intership, ship/shore and safety: Canadian Coast Guard search and rescue. 156.200 156.200 Intership, ship/shore and commercial: Commercial fishing only.
Page 108 Intership, ship/shore and commercial. Commercial fishing only. 156.575 156.575 Intership, ship/shore, commercial, non-commercial, safety and ship movement. 156.575 156.575 Intership, ship/shore and non-commercial. For marinas and yacht clubs on the east coast and on Lake Winnipeg. Ray50 / Ray60 / Ray70...
Page 109 Area of CH No. TX Freq RX Freq operation 156.625 156.625 EC, PC Intership, commercial and non-commercial May be used to communicate with aircraft and helicopters in predominantly maritime support operations. 156.675 156.675 Intership, ship/shore and commercial. Commercial fishing only. 156.675 156.675 All areas...
Page 110 162.000 Public correspondence, Port operations and Ship movement. 156.025 160.625 Public correspondence, Port operations and Ship movement. 156.075 160.675 Public correspondence, Port operations and Ship movement. 156.125 160.725 Public correspondence, Port operations and Ship movement. Ray50 / Ray60 / Ray70...
Page 111 CH No. TX Freq RX Freq Single Freq Use 156.175 160.775 Public correspondence, Port operations and Ship movement. 156.225 160.825 Public correspondence, Port operations and Ship movement. 156.275 160.875 Public correspondence, Port operations and Ship movement. 156.325 160.925 Public correspondence, Port operations and Ship movement. 156.375 156.375 Intership, Port operations and Ship movement.
Page 112 The national channels listed above have been allocated for the specific use within the countries listed. To use these channels you must have the appropriate license. WX Channels (North America only) Weather Channel Frequency in MHz 162.550 162.400 162.475 162.425 162.450 162.500 162.525 161.650 161.775 WX10 163.275 Ray50 / Ray60 / Ray70...
Page 113: Appendix D Phonetic Alphabet
Appendix D Phonetic alphabet To help make call letters more clearly understood, and to assist in spelling out similar sounding or unfamiliar word, radiotelephone users employ the international phonetic alphabet. ALPHA NOVEMBER BRAVO OSCAR CHARLIE PAPA DELTA QUEBEC ECHO ROMEO FOXTROT SIERRA GOLF...
Page 114: Appendix E Prowords
I have completed this part of the message and am inviting you to reply. RECEIVED Receipt acknowledgement. SAY AGAIN Repeat your message. STATION CALLING Used when a station is uncertain of the identity of a station which is calling. Ray50 / Ray60 / Ray70...
Page 116 www.raymarine.com...

This manual is also suitable for:

Ray60 Ray70

Raymarine RAY50 Installation And Operation Instructions Manual

Chapter 1 Important Information

Chapter 2 Document and Product Information

Chapter 3 Planning the Installation

Chapter 4 Cables and Connections

Chapter 5 Location and Mounting

Chapter 6 Getting Started

Chapter 7 Digital Selective Calling (DSC)

Chapter 8 VHF Operations

Chapter 9 Hailer, Fog Horn, and Intercom

Chapter 10 Maintenance

Chapter 11 Troubleshooting

Chapter 12 Technical Support

Chapter 13 Technical Specification

Chapter 14 Spares and Accessories

Appendix A NMEA 0183 Sentences

Appendix B NMEA 2000 PGN List

Appendix C VHF Channels

Appendix D Phonetic Alphabet

Appendix E Prowords

Quick Links

Troubleshooting

Related Manuals for Raymarine RAY50

Summary of Contents for Raymarine RAY50

This manual is also suitable for:

Table of Contents