Service Mode; Outline; Service Data Setting - Canon LaserBase MF3220 Series Service Manual

Error Code
00AE
00AF
00B1
00B2
00B3
00B4
00B5
00B6
00B8
00BA
00BB
00BC
00BD
00BE
00BF
00C1
00C2
00C4
00C5
00C9
00CA
00CB
00CF
00D0
00D1
00D2
00D3
00D8
00D9
00DA
00DB
00DC
00DE
00E0
00E1
00E2
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EE
00EF
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00FC
00FD
00FE
00FF

5.4 Service Mode

5.4.1 Outline

5.4.1.1 Service Data Setting

Service mode has the following service data items. These items can be
checked/changed according to the menu on the display.
Description
Can't finished V.8 procedure or detect V.21 signal after CM signal
Modem can't enter into control channel after TX side sending out RCP signal
for V34
Can't finish V.8 procedure or detect V.21 signal after ANSam signal within 35 sec.
Can't detect phase 2 signal after our side sending CJ signal within 30 sec
Can't detect correct V.21 or JM signal after sending CM or CJ signal.
Can't detect correct phase 2 signal within 25 second after CM/JM signal exchange.
Can't detect phase 3 signal after Phase 2
Can't detect phase 4 signal within 25 sec after CM/JM exchange.
Remote side disconnect after our side sending DCS signal in V.34.
Cannot received correct signal after our side sending DTC signal in V.34.
Every time our side received DIS signal after sending DTC in V.34.
Modem can't ready within 10 second after entering primary channel in V.34.
Can't detect correct V.21 or JM signal after detected FSK frequency.
Remote side no document to be polled after V.8 handshaking.
Capability no match after V.8 handshaking
At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving
unit.
Remote side disconnect after sending out V.8 CM signal.
After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.
Received DCN signal after sending MPS signal.
At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit.
After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP.
After sending EOP signal, the received is DCN signal.
Received incorrect signal after sending DTC signal for V.34 polling.
Received ERR signal after sending EOR_NULL.
Received incorrect response after sending PPS_EOP signal
Received DCN after sending PPS_EOP signal
Received DCN after sending PPS_NULL signal
Can't detect correct phase 3 signal for poling.
Can't detect correct phase 3 signal after detect silence after phase 2.
Can't detect phase 4 signal within 30 sec.
Can't received any T.30 signal within 30 sec within phase 4.
Received T.30 signal in phase 4 other than DCS, DIS or DTC
Remote side no SUB capability.
At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer.
Received incorrect response after sending PPS_NULL.
Can't receive any response in RR response procedure after sending PPS_NULL.
At phase D, transmitting units out PPS_MPS 3 times consecutivery but receive no answer.
Received incorrect response after sending PPS_MPS signal
Can't receive any response in RR response procedure after sending PPS_MPS.
Reseived DCN after sending PPS_MPS.
At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer.
Receive PIN signal after sent last page data.
Can't receive any response in RR response procedure after sending PPS_EOP.
At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer.
Received incorrect response after sending EOR_NULL.
Can't receive any response in RR response procedure after sending EOR_NULL.
At phasa-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer.
Received incorrect response after sending EOR_MPS.
Received ERR signal after sending EOR_MPS.
Can't receive any response in RR response procedure after sending EOR_MPS.
At phasa-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer.
Received incorrect response after sending EOR_EOP
After Received ERR, our side can't received response after sending EOR_EOP command.
Can't receive any response after sending CTC.
Can't speed down to lower speed.
Memory full for transmission
REDAIL ALL FAIL
0012-6439
SERVICE'S CHOICE
Use it to select service data to suit the country/region of installation, to reset
the user data, or to set the transmission/reception speed.
ADJUST
Use it to execute margin adjustment for printing or reading.
VERSION DISPLAY
Use it to indicate version information on the display.
SOFT SWITCH
Chapter 5
5-3