Table of Contents
Advertisement
Command and Response Table for SIS Commands
Command Function
Input selection
:
The three command codes in the input selection commands and view input commands; !, &, and %; can be used
NOTE
interchangeably.
Select input
Select input
Select input
View input
View input
View input
Channel mute
WARNING:
Risk of serious physical injury: The channel mute command mutes the data on the switched output only. The output
continues to emit light, which may be harmful to the eyes. The mute function has no affect on the looped-through outputs.
Mute output
Unmute output
Show video mute status
Reclocking
Set reclocker mode
Example:
Example:
Show reclocker mode
Front panel security lockout (executive mode)
Lock front panel
Unlock front panel
Show lock status
Resets
Reset mute
Reset whole switcher
Information Requests and Unit Name
Information request
Show firmware version
Example:
Request part number
Show input connections
status
Show temperature
Show transceiver module
status
Set switcher name
Example:
Set switcher name to
factory default
View switcher name
ASCII Command
Response
(Host to Unit)
(Unit to Host)
X!
X!
!
In
•All
X!
X!
&
In
•RGB
X!
X!
%
In
•Vid
X!]
!
X!]
&
X!]
%
]
1B
Vmt1
]
0B
Vmt0
X@]
B
X&
Rte08*
08*
=
08*0=
Rte08*00
08*0=
Rte08*03
X&]
08=
]
1
Exe1
X
]
0X
Exe0
X@]
X
E
}
]
ZZ
Zpz
E
}
]
ZXXX
Zpx
X!
I
In
•Vmt
X$]
Q
]
Q
1.23
N
60-1172-nn
X%
X%
0LS
1
2
X^]
20S
X#
X#
0*1I
1
2
EX*
}
X*]
CN
Ipn•
E
}
Switcher_1CN
Ipn•Switcher-1
E
}
•CN
Ipn•FOX-SW8
E
}
X*]
CN
Additional description
]
X!
Select input
]
X!
Select input
]
X!
Select input
X!
Input
is selected for output.
X!
Input
is selected for output.
X!
Input
is selected for output.
Blank data on switched output.
Output data on switched output.
Switched output mute status is
X&]
Set the reclocker mode to
]
Set the output reclocker mode to bypass (do not reclock).
]
Set the output reclocker mode to 4.25 Gbps (default).
Inputs cannot be selected from the front panel.
Inputs can be selected from the front panel.
Front panel lock status is
Unmute the output.
Unmute the output, unlock the front panel, and select
input 1.
X@]
X!
In
indicates the selected input. Vmt
output mute status (
X$
is the firmware version.
The factory-installed FOX SW8 controller firmware
version is 1.23 (sample value only).
]
nn indicates the transmission mode.
= multimode,
01
X%
X%
X%
]
X%
Each
indicates the status of an input,
3
4
...
8
= no light on this input,
0
X^
= degrees Fahrenheit.
X#
X#
X#
]
Show all installed transceiver modules.
3
4
...
8
= none,
= multimode,
0
1
Set the switcher name to
]
Set the switcher name to "Switcher-1".
]
Restore the factory default name.
to output.
to output.
to output.
X@
.
X&
.
X@
.
X@
indicates the
= unmuted,
= muted)..
0
1
= singlemode.
02
= light received.
1
= singlemode.
2
X*
.
FOX SW8 • Remote Control
11
Advertisement
Table of Contents
