When the user authentication has been set ... 2-17 2.6.2 When the account track has been set ... 2-17 Fax reception using the box ... 2-18 2.7.1 Type of boxes ... 2-19 2.7.2 Operations of the PC-fax RX feature ... 2-21 C450...
Page 4
Canceling communication in progress ...3-35 3.9.2 Canceling reserved jobs ...3-36 3.10 Confirm the job list ...3-37 3.11 Confirming communication results ...3-38 3.12 Memory transmissions and quick memory TX ...3-41 3.12.1 Memory transmission ...3-41 3.12.2 Quick memory transmission ...3-41 x-ii C450...
Page 5
Recording after reducing to fit in paper ... 4-9 Reception information ... 4-17 Troubleshooting Cannot send messages ... 5-3 Cannot receive messages ... 5-4 Error message displayed ... 5-6 Call for service ... 5-7 Specifications Specifications ... 6-3 C450 x-iii...
Page 6
Polling Polled transmission ...9-3 9.1.1 Polled transmission ...9-4 Polling reception ...9-6 Bulletin ...9-9 9.3.1 Write a document to the bulletin board ...9-10 9.3.2 Receive by polling a document written to the bulletin board of a destination (fax) ...9-13 x-iv C450...
Page 13
Introduction Introduction Thank you for your purchase of the Konica Minolta digital electronic photo- copying machine. This user's guide describes operating procedures and precautions for use of the fax functions. Please read this user's guide before starting operation of the machine.
To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company For products approved after July 23, 2001, the REN for this product is part of the Introduction C450...
Page 15
If trouble is experienced with this equipment FK-502, for repair or warranty information, please contact the Konica Minolta dealer location where you purchased this equipment. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Page 16
“Caution” is intended to alert the user to the possibility that a dis- regard for the caution may result in minor injuries or in physical dam- age. Be sure to focus your attention on the caution headings when reading the copier user's guide. Introduction C450...
PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network terminal point. In the event of problems, you should contact your equipment supplier in the first instance. C450...
Getting started (fax) Sending Perform the following basic procedure to send a fax. Press [Fax] on the control panel to start the fax mode. Set the functions as necessary. Fax screen Scan setting screen Application screen Comm. setting screen Introduction C450...
Page 19
[Del.] to clear your entry. – Press [C] (clear) to clear the whole entry. Place the original on the machine. – For details, see “Placing the original on the machine” on page 3-7. Press [Start] on the control panel. C450...
This function allows you to specify the time to start sending a fax. You can save money by specifying a transmission to start during the night or early in the morning when telephone charges are less. Detail For details, see “Timer transmission” on page 3-47. 1-10 Introduction P.005 / 010 C450...
Page 21
3-41. Sending faxes to a foreign country You can employ a lower transmission rate if you send a fax to the location at which the communication condition is poor. Detail For details, see “International communication” on page 3-50. C450 1-11...
Page 22
You can also set the width of marginal erasure according to your preference. Ordinary transmission Frame erasure transmission Detail For details, see “Frame erase transmission” on page 7-13. 1-12 Introduction Width of erasure C450...
Page 23
You can send a fax by designating the paper size for the document to be sent. It is useful if you want to send only a portion of the original. Detail For details, see “Scan size” on page 7-22. C450 1-13...
Page 24
You set document pages of mixed sizes on the RADF. Detail For details, see “Mixed original” on page 7-8. 1-14 Introduction Transmitted and reproduced in the same size as the original pages at the destination. C450...
Page 25
You can send a fax that has been read and stored in hard disk in the facsimile when a polling command is sent from the recipient. Detail For details, see “Polling reception” on page 9-6. C450 Top/Bottom bind Transmission Left/Right bind...
Page 26
Sending a fax with the Super G3 mode disabled You can send a fax with the Super G3 mode disabled if V.34 protocol is not available because of restrictions on the Private Branch Exchange (PBX). Detail For details, see “V.34 OFF” on page 7-41. 1-16 Introduction C450...
Page 27
You can send a fax to a recipient via an intermediate relay station. Original station Detail For details, see “Relay transmission request” on page 7-35. This machine is not provided with a relay delivery function. C450 Intermediate relay station Toll call Remote station Local call...
Page 28
Sending a fax protected with a password You can send a fax protected with a password if the closed communication is set at the recipient. Detail For details, see “Password transmission” on page 7-27. 1-18 Sender Classified document box Introduction Receiver C450...
Page 29
To be sent with the edge of the character made clear Transmission can be made after adjustments are made so that blurred char- acters are made clear to give them a smooth impression. Detail For details, see “Sharpness” on page 7-19. C450 1-19...
Page 30
To be saved in the box An original that has been read can be saved in the box created in the internal hard disk. Detail For details, see “Fax reception using the box” on page 2-18. 1-20 Mail server E-mail Introduction Hard disk C450...
Text formatted in this style pro- vides additional assistance. % Text formatted in this style describes the action that will ensure the desired results are achieved. C450 An illustration inserted here shows what operations must be performed. 1-21...
Page 32
Text highlighted in this manner contains references for more detailed in- formation. Special text markings [Stop] key The names of keys on the control panel are written as shown above. MACHINE SETTING Display texts are written as shown above. 1-22 Introduction C450...
If the width (Y) of the paper is longer than the length (X), the paper has a horizontal or land- scape orientation, indicated by v. C450 Whenever paper dimensions are mentioned in this manual, the first value always refers to the width of the paper (shown as “Y”...
User's guide – Facsimile operations (this manual) This manual contains details on operating procedures for faxing. - Refer to this user's guide for details on operating procedures for fax func- tions when the fax kit is installed. 1-24 Introduction C450...
Page 35
Introduction User's guide – Enlarge display operations This manual contains details on operating procedures for using copy func- tions in enlarge display mode. - Refer to this user's guide for details on operating procedures in enlarge display mode. C450 1-25...
However, these constraints vary depending on a device that makes up the network. For more information, refer to the administrator of the network that you use. C450...
While the machine is in copy mode, the indicator on the [Copy] key lights up in green. For details, refer to "User's guide – Copy operations". Before use Reset Copy Interrupt Power Proof Copy WXYZ Stop Start Star Data Main P Main Power er C450...
Page 41
[Utility/Counter] key [Mode Memory] key Contrast dial [Enlarge Display] key [Accessibility] key C450 Description Press to clear all settings (except programmed set- tings) entered in the control panel and touch panel. Copy screen is displayed after scanning original doc- uments. Then It change to the interrupt mode. While...
Page 42
Description Press to display the help main menu screen, where de- scriptions of the various functions and details of oper- ations can be displayed. For details, refer to "User’s guide – Copy operations". Before use C450...
For details, refer to “Telephone line settings” on page 11-34. Item Dialing method Receive mode C450 Description Set the name of this machine. The name is a string of up to 30 characters. The name can contain with any alphanumeric charac- ter and symbols.
Press [One-Touch Registration]. – For utility mode, the number displayed in the key can also be se- lected by entering it through the numeric keypad. In the case of [One-Touch Registration], enter 1 through the key- pad. Before use C450...
Page 45
Registering the box name. This machine can specify a box in an in- ternal hard disk as a fax destination. – If it has been registered. This feature is convenient when storing a picture to a box simultaneously with fax transmission. C450...
Page 46
For the registration method of the boxes, see “User’s guide – Box operations.” Press [Index] to entry the characters for search and then press [OK]. – Press the search key of the search character you want to register from among [ABC] - [etc]. 2-10 Before use C450...
Page 47
When [E-Mail] or [User Box] is selected in the step 5. There is no [Line Setting]. Press [OK]. Registration is performed and the registered destination is displayed on a list. When proceeding with the registration of the address book, go to step Press [Exit]. C450 2-11...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [One-Touch Registration], enter the “1” on the keypad. Press [Fax]. Press [Program]. 2-12 Before use C450...
Page 49
Select the program no. you want to register and then press [Edit]. Press [Name], enter the name of the program and press [OK]. – The name can be a string of up to 24 characters. – For the operation of the entering character, see page 13-4. C450 2-13...
Page 50
For the registration method of the boxes, see “User’s guide – Box perations).” Press [Close] and then press [OK]. – To stop registering the program, press [Cancel]. The list of program is displayed. When proceeding with the registration of the program, go to step 5. Press [Exit]. 2-14 Before use C450...
No. of dest. Memory Off-hook Name Page indicator Page list C450 Description The list of the jobs in the queue for execution, the job history, and the error jobs is displayed. Displays program select screen. Displays group select screen. Displays address book select screen.
Page 52
TX or polling RX is set. The destination set is displayed. The description according to the operations being set on the right side is displayed. For the operation of the fax, the explanation of each function and the broadcast destinations are displayed. Before use C450...
2.6.1 When the user authentication has been set Detail For details of the user authentication and the account track, see “User's Guide – Copy Operations”. 2.6.2 When the account track has been set C450 2-17...
PC-Fax RX feature, see “User's guide – Box operations". - When the box of this machine is specified as a destination while in the fax sending, documents that have been read can be saved in the box. Sender Original 2-18 Before use Hard disk C450...
Fixed box (0) Specified box (public user box / personal user box: no. 1 - 99999999) C450 Function When the fixed box is specified as a place into which documents received are stored in the PC-fax RX feature, the documents received are saved in this box.
Page 56
For details, refer to “Memory reception” on page 8-3 This box is used when the confidential print is made optionally in the print controller. Detail For details of the secure print user box, see “User's guide – Printer operations". Before use C450...
Fax RX setting: ON RX output: fixed box Fax RX setting: ON RX output: specified box C450 Reception method Documents received are not saved in the box, but printed immedi- ately. In the following cases, however, documents received are saved in the box.
Re- fer “Transmission applications” on page 7-3 to for further details. Press [Fax] on the control panel to open the fax screen. Press [Scan Setting] to set the function and then press [OK]. C450...
Page 62
For details, refer to “Opening the scan setting screen and comm. setting screen” on page 7-3. Press [Comm. Setting] to set the function and then press [OK]. – See “Transmission applications” on page 7-3 for detail. Text Standard Single sided Fine Transmission C450...
Page 63
[Restrict], [Direct Input] is not displayed. For the set- ting of [Manual Destination Input], contact your administrator. The fax number entered is displayed in the broadcast destinations. Place the original on the machine. – For details, refer to “Placing the original on the machine” on page 3-7. C450...
Page 64
If the transmission fails, TX report is automatically output (if the TX report is programmed to print). For details of report settings, see “Report settings” on page 11-66. – For more information about the TX report, see “TX report” on page 12-9. Transmission C450...
ADF. Adjust paper guides. – In mixed original mode, extend the paper guides to fit the largest paper size, and place the remaining origi- nals aligned in the top left corner. C450...
Use the platen glass for originals that cannot be placed in the ADF (such as a book or thick/thin originals). Placing originals on the platen glass Open the ADF. Place the original face down in the left rear corner, aligning the edge with the left measuring guide. Gently close the ADF. Transmission C450...
Place the next original on the platen glass and press [Start]. – Repeat this procedure until all orig- inals to be sent have been scanned. The scanned originals are stored in memory. Press [Finish]. The document reading mode is canceled. Press [Start]. Transmission begins. C450...
[Start]. – Repeat this procedure until all orig- inals to be sent have been scanned. The scanned originals are stored in memory. Press [Finish]. The Document reading mode is canceled. Press [Start]. Transmission begins. 3-10 Transmission C450...
Detail The condition for transmission cannot be set in units of page. Setting transmission conditions Press [Scan Setting] on the fax screen. Press the key desired to be set C450 3-11...
Press this when scanning originals containing photographs (half- tone) only. Press this when scanning originals containing text which are thin- ly written in pencil as a whole. Transmission C450...
9 steps. Standard is set at the time of purchase. Density seting Light Std. Dark C450 Description Press to scan originals so that they are lighter than the density de- tected with Standard. Press to scan originals at a density that is between Darker and Lighter.
There are 2 types. Single sided is set at the time of pur- chase. Simplex/Duplex setting Single sided Double sided 3-14 Description Press this when scanning one-sided originals. Press this when scanning two-sided originals. Transmission C450...
When ultra fine or super fine has been selected and the receiving ma- chine is not equipped with the resolution, originals are sent at a resolution corresponding to the reception capability of the receiving machine. C450 Description Press this when the sending time is cut short.
Press a key of setting you want to confirm Confirm the settings. – The four kinds of the setting as follows can be confirmed. – Destination Confirming the destination. – Pressing [Dest.] in the screen shown by pressing [Details] allows you to change the destination. 3-16 Transmission C450...
Page 75
Pressing [Fwd. ] to display the next screen, pressing [ Back] to display the previous screen. – Communication setting Confirming the communication setting. Press each setting key in the screen, and the communication setting or line setting screen corresponding to each appears, and the setting can be change. C450 3-17...
Page 76
The fax screen will be restored. Detail When the scan setting or communication aetting is changed, It moves to the scan setting screen or communication setting screen. It does not re- turn to the mode check screen. 3-18 Transmission C450...
A destination that is shown on the mode check screen can be registered in [Address Book]. Registering from the mode check screen Press [Fax] on the control panel. Press [Mode Check] on the control panel. Press [Destination] Select destination that you want to register in [Address Book], and then press [Details]. C450 3-19...
Page 78
Press [Name] to enter the registration name, and then press [OK]. When there is no trouble found with the entries, press [Yes]. – When cancelling the registration, press [No]. Press [Close] three times to return to the fax screen. A selected destination is registered in [Address Book]. 3-20 Transmission C450...
Press [DEL.] on the fax screen, if a mistake has been made in entering a single number. – Press [C] (clear) to clear the whole entry. The fax number that has been entered is displayed in the broadcast destinations. Press [Start]. Transmission begins. C450 3-21...
Page 80
When the destination is an e-mail address, the subject, the text, the file name, and the from of the sender can be set manually. For details, refer to “Confirming settings and communication results” on page 3-16 3-22 when desiring to display the next or previous Transmission C450...
Page 81
Each time the [Name between the fax number and the registration name. – Two or more destination can be specified. – A search is made when the characters at the beginning coincide each other. C450 Dest.] is pressed, the display switches 3-23...
Page 82
Press [Name], [Fax Number] or [E-Mail] and enter an item you want to make a search for. – Press [OK]. The results of the search will be displayed. Searching in [LDAP Search] – – Press [LDAP Search]. 3-24 Transmission C450...
Page 83
Press the key of the destination name to which you want to send the fax. – An alphabet shown before the key represents the following descrip- tion. The destination that has been specified is displayed in the broadcast destinations. Press [Start]. Transmission begins. C450 Dial E-mail 3-25...
Page 84
[Restrict], [Direct Input] is not displayed. For the setting of [Man- ual Destination Input], contact your administrator. Press [Direct Input] in the faxscreen. Enter a dialing symbol such as tone, pause or “-” as required, and then enter the fax number of the destination through the keypad. 3-26 Transmission C450...
Page 85
A fax transmission is made to the destination to which transmission was made previously. – For details of Recently dial #, see “Manual redialing” on page 3-30 – Save in user box An image is saved in the internal hard disk. Press [Start]. Transmission begins. C450 3-27...
Specification can also be made by pressing the [Group] in the direct input to enter the group no. (01 to 99, 00). When specification is made by using the method above, transmission is made to all destinations registered in the group. 3-28 Transmission C450...
To delete a destination, select the destinations to be deleted in the list and then press [Del.]. – Pressing [Details] displays the detail information screen. – Pressing The message screen appears. Press [Yes]. Press [Close] twice. The fax screen will be restored. C450 displays the previous or next screen. 3-29...
To redial manually Press [Direct Input], and then press [Recently Dialed #]. – Up to the five newest facsimile numbers which were dialed are dis- played. Select the destination you want to redial from the displayed destina- tions. 3-30 Transmission C450...
When this happens, transmit the document by selecting auick memory TX (you can select the quick memory TX by clearing memory TX in the comm. setting screen). Detail For details, refer to “Error message displayed” on page 5-6. C450 3-31...
The redialing function is set at factory to redial one time after a three- minute interval. The number of redials and the redialing interval can be changed in the utility mode. For details, refer to “Telephone line settings” on page 11-35. 3-32 Transmission C450...
3-11 for setting functions on the fax screen. – See “Opening the scan setting screen and comm. setting screen” on page 7-3 for setting functions on the fax application screen. Select a destination. Press [Start]. C450 3-33...
Pressing [Start] on the control panel allows the off-hook start fax communication screen confirmation to appear. Transmission starts when you press [Yes]. – When the external telephone is connected, hang up the receiver of the external telephone after pressing [Start]. Transmission begins. 3-34 Transmission C450...
Press [Fax TX]. Check to see if the active jobs in the [Current Jobs] have been selected. Select the job you want to delete, and press [Delete]. Press [Yes]. Transmission is cancelled. Press [Exit]. The fax screen will be restored. C450 3-35...
Select the reservation document desired to be canceled, and press [Delete]. – Press The message appears. Press [Yes]. The reserved document is deleted. Press [Exit]. The fax screen will be restored. 3-36 to display the next or previous screen. Transmission C450...
The remaining amount of memory is displayed at the upper right of the fax screen. While in the fax communication, this memory is used and its remaining amount is displayed. Fax screen will be restored. C450 displays the previous or next screen. 3-37...
Confirming communication results Pressing [Job List] in the fax screen allows you to check the results of trans- mission. Press [Job List] on the control panel. Press [Print], [Fax TX] or [Fax RX/User Box]. Press [Job History]. 3-38 Transmission C450...
Page 97
In the cases of other than the above, the type of the copy, print and fax-RX etc. is dis- played. – Document Name: The name of the document that has been received or saved is dis- played. C450 3-39...
Page 98
TX report or the fax RX report. At this time, the activity report, TX report, and RX report can be printed out. – Pressing [Details] displays the detail information screen. Press [Exit] twice after completion of confirmation. The fax screen will be restored. 3-40 Transmission C450...
This allows documents to be sent without exceeding memory ca- pacity in the case of sending a large number of pages. Detail In the case of the quick memory RX, the “Memory” on the screen remains unchanged. C450 3-41...
Set the original document. – For details, refer to “Placing the original on the machine” on page 3-7. Press [Start]. The FK-502 reads the document and stores it in memory as a reserved document before transmission starts. 3-42 Transmission C450...
Page 101
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, see “Cannot send messages” on page 5-3. C450 3-43...
: Number of originals set function is automatically cancelled. Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting] on the fax screen. Press [Quick Memory TX]. 3-44 Transmission P.005 / 010 C450...
Page 103
Designate the destination. – For details, refer to “Selecting one destination” on page 3-21. Set the original document. Press [Start]. The FK-502 reads the document and starts transmitting as each page is scanned. C450 3-45...
Page 104
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, see “Cannot send messages” on page 5-3. 3-46 Transmission C450...
(bulletin), polling RX (normal: When selecting polling RX in advance, timer TX can be set.) Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting] on the fax screen. Press [Timer TX]. C450 3-47...
Page 106
Set the original document. – For details, refer to “Placing originals on the platen glass” on page 3-8. Press [Start]. The FK-502 reads the document and holds it in memory until the spec- ified time when transmission starts. 3-48 Transmission C450...
Page 107
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, see “Cannot send messages” on page 5-3. C450 3-49...
Polling TX (normal), polling RX (normal), polling TX bBulletin), polling RX (bulletin) Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting] on the fax screen. Press [Line Setting]. 3-50 Transmission C450...
Page 109
7-3 for informa- tion about setting functions in the fax application screen. Set the original document. – For details, refer to “Placing originals on the platen glass” on page 3-8. C450 3-51...
Page 110
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, see “Cannot send messages” on page 5-3. 3-52 Transmission C450...
Fax basic screen default setting menu is displayed in the FROM space of sender information. 3.16.2 Set to outside body text From: 01234567890 Detail See “Header/Footer position” on page 11-31 for information about set- ting. C450 01/20/2005 01:23#012 p.5/10 01/20/2005 01:23#012 p.5/10 3-53...
When mixed original is selected and mixed size originals are set and sent as shown in the following illustration, the sender information is printed on the shorter side of the small original. 3-54 Mixed original is selected Mixed original is not selected Transmission C450...
Set the FK-502 to this mode when an external telephone (or an answering machine) is connected and the majority of incoming calls are telephone calls. Arrival of a call C450 External telephone rings Lift the handset and start talking For faxes, press [Start] to receive...
Refer to “Telephone line settings” on page 11-34 for information about setting this mode. Refer to “Telephone line settings” on page 11-34 for information about setting the number of rings before reception. Arrival of a call Starts receiving message automatically Reception Received document C450...
Press [Start] on the off-hook menu. – Pressing [Start] on the control panel open the off-hook screen. Transmission starts when you press [Yes]. Reception begins. C450 External telephone rings Lift the handset and start talking For faxes, press [Start] to receive...
“Telephone line settings” on page 11-34. Documents may not be able to be received memory is full. In addition, check that there is paper in the paper tray. For details, refer to “Cannot receive messages” on page 5-4. Reception C450...
This function is referred to as the memory substitute reception. - The stored document is printed when you solve the problem (such as a paper jam). - Memory substitute reception will not work if the memory is full. C450...
(the default is 96%). Detail Refer to “TX/RX setting” on page 11-37 for more detailed information on the minimum reduction rate. Original Received document Reduced at the minimum reduction rate Reception C450...
If papers of appro- priate size are not set on the paper tray, the data are recorded on papers of the nearest size after the document size being reduced. Original C450 Received document Reduced to fit in paper...
Page 122
A3 w Reception 294 - 375 mm 375 mm or more 8.5 × 14 w 11 × 17 w or more 312 - 384 mm 384 mm or more B4 w A3 w 384 mm or more A3 w C450...
Page 123
The machine looks for the second appropriate paper in order as shown in the table. If print separate fax page is set to ON in the utility mode, the facsimile looks for paper to record the document on more than one pa- per. C450 4-11...
Page 124
8.5 × 11 v 8.5 × 11 v 8.5 × 11 w 8.5 × 11 w A4 v A4 v A4 w A4 w A4 w A3 w A4 v B4 w B4 w A4 v A3 w A4 w C450...
Page 125
A3 w If recording paper of B5 w, B5 v, A4 w or A4 v size is selected, the image on that page may be extended over to multiple pages when recorded. C450 5.5 × 8.5 8.5 × 11R 8.5 × 11 5.5 ×...
Page 126
If [Print Paper Selection] is set to [Fixed Size]: The appropriate paper is selected among 8.5 × 11, 8.5 × 14 and 11 × 17 (A4, B4 and A3). If it is not available, the message stays appearing until the paper is loaded. 4-14 Reception C450...
Page 127
[Tray Selection for RX Print]. If [Print Paper Selection] is set to other than [Auto Select] and [Tray Se- lection for RX Print] is set to other than [Auto]: The setting in the [Tray Selection for RX Print] takes precedence. C450 4-15...
Page 128
Recorded after being reduced to fit in the appropriate size of to fit in the specified size of paper paper Recorded after page division Recorded after being reduced depending on the paper used to fit in the specified size of paper Reception C450...
Set to inside body text RX time: 01/20/2005 Set to outside body text RX time: 01/20/2005 Set to OFF Detail See “Header/Footer position” on page 11-31 for information about set- ting. C450 Original R001 P.001/003 Original R001 P.001/003 Original 4-17...
Is the telephone line connected properly? Is there a problem with the receiv- ing machine? C450 Corrective actions Check the transmission procedure and then try sending again. Using program dialing or abbreviated dialing, there may be an error in registration of the fax number. Try printing out the abbreviated dialing list and check if the number is reg- istered correctly.
When a wrong sub-address is received with the confi- dential RX user box set, there may occurs a communi- cation error, thus resulting in the reception unavailable. Check the sender side to see if the sub-address is set. C450...
Page 135
No outputs Is the fax RX set- ting? Hasn't the memory RX been set? C450 Corrective actions Identify the box used by PC-fax RX features to save the file. When the memory RX is set, print the document re- ceived by following the procedure given below.
Ask the sender to send the document again. • When the memory becomes full reading the document: To transmit the document which was read, press the [Start] or press the [Stop] to discontinue the transmission. Troubleshooting C450...
Write down the trouble code number of the message. Turn off the auxiliary power switch and main power switch. Disconnect the power cord from the outlet. Contact your service representative and inform the representative of the trouble code number. C450...
Page 141
Transmission time Coding methods C450 Specifications 40 GB* Approx. 9000 pages* (numbers of pages in the case of storing KONICA MINOLTA standard A4-size pages containing approximately 700 characters at “fine” resolution) Subscriber telephone lines (including facsimile communication networks) PBX lines Ultra fine: 600 dpi ×...
Page 142
Item Max. scanning size Max. recording size * The internal hard disk is common used of each function of the copy, the scan, the print and the box. Specifications 11 inch × 17 inch (280 mm × 431 mm) or A3 (420 mm × 297 mm) Width: 297 mm Length: Max.
If you send a fax with an application function, open the scan setting or comm. setting screen and set the functions you want to use. Press [Fax] on the control panel to open the fax screen. Press [Scan Setting] or [Comm. Setting] on the fax screen. C450...
Page 146
When the dedicated screen is displayed: Set a function in the screen displayed and then press [OK]. – When a function is selected: Press [OK]. – Press [Cancel] to return to the original communication setting. The fax screen will be restored. Transmission applications C450...
Release the setting that has been set and return to the preceding screen. [Reset] Turn off all the functions provided on the screen. Function Mixed original: Bind position: C450 Scan setting screen Application screen Comm. setting screen Description You can send document pages of mixed sizes in a single se- quence of operations.
Page 148
A lower baud rate will be employed. (page 3-50) Error correction mode (ECM) can be disabled. (page 7-38) When the V.34 protocol can not be used due to restrictions of exchange equipment, the V.34 mode is disabled for transmis- sion. (page 7-41) C450...
Page 149
Transmission applications Detail The key representing the function you select will be appear reversed. Press [Cancel] to return to the fax screen. V.34 is a communication mode used by the Super G3 fax. C450...
Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting] and then press [Application]. Press [Mixed Original]. Transmission applications Transmitted and reproduced in the same size as the original pages at the destination. C450...
Page 151
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. C450...
Mixed original, polling RX (normal), polling RX (bulletin) Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting] and then press [Application]. 7-10 Top/Bottom bind Transmission Left/Right bind Transmission applications Destination fax C450...
Page 153
Set other functions if necessary. – See “Setting transmission conditions” on page 3-11 for information about setting functions in the fax screen. See “Application func- tions overview” on page 7-5 for information about setting functions in the fax application screen. C450 7-11...
Page 154
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. 7-12 Transmission applications C450...
If frame erase are combined, the effect of frame erasure applies to the original page format that is yet to be divided. Functions incompatible Quick memory TX, number of originals, polling RX (normal), polling RX (bulletin) C450 Width of erasure 7-13...
Page 156
[+] or [-]. Press [OK]. – To release the setting, press [OFF] or [Cancel]. The application screen will be restored. Press [OK]. The scan setting screen will be restored. Press [OK]. The fax screen will be restored. 7-14 Transmission applications C450...
Page 157
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. C450 7-15...
Both of the platen glass and the ADF can be used. Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting] and then press [Application]. Press [Background Adjustment]. 7-16 Transmission applications C450...
Page 159
Designate the destination. – See “Selecting one destination” on page 3-21 for designating the destination. Set the original document. – See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. C450 7-17...
Page 160
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. 7-18 Transmission applications C450...
Both of the platen glass and the ADF can be used. Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting] and then press [Application]. Press [Sharpness]. C450 7-19...
Page 162
See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. Press [Start]. The FK-502 reads the document and stores it in memory as a reserved document before transmission starts. 7-20 Transmission applications ] or [ ] to the [+] or [-] side. C450...
Page 163
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. C450 7-21...
Quick memory TX, polling RX (normal), number of originals, polling RX (bulletin) Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting] and then press [Application]. 7-22 Transmission applications C450...
Page 165
Set other functions if necessary. – See “Setting transmission conditions” on page 3-11 for information about setting functions in the fax screen. See “Application func- tions overview” on page 7-5 for information about setting functions in the fax application screen. C450 7-23...
Page 166
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. 7-24 Transmission applications C450...
Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Scan Setting]. Press [File Type]. Select the file type. Press [OK]. – To release the setting, press [Cancel]. The Scan Setting screen will be restored. C450 7-25...
Page 168
The FK-502 reads the document and stores it in memory as a reserved document before transmission starts. Detail To cancel transmission, see “Canceling transmission” on page 3-35. If transmission fails, refer to “Cannot send messages” on page 5-3. 7-26 Transmission applications C450...
Polling TX (normal), polling RX (normal), confidential TX, polling TX (bulle- tin), polling RX (bulletin), relay TX req Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Password TX]. C450 7-27...
Page 170
– See “Selecting one destination” on page 3-21 for information about designating the destination. Set the original document. – See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. 7-28 Transmission applications C450...
Page 171
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. C450 7-29...
Polling TX (normal), polling RX (normal), polling TX (bulletin), polling RX (bulletin), relay TX req, password TX Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. 7-30 Transmission applications Sender Classified document box Receiver C450...
Page 173
Press [C] (clear) to clear the whole entry. If a password is needed, press [Yes] and enter the password. Press [OK]. – To release the setting, press [OFF] or [Cancel]. The comm. setting screen will be restored. Press [OK]. The fax screen will be restored. C450 7-31...
Page 174
See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. Press [Start]. The FK-502 stores the document in memory before starting transmis- sion. Detail To interrupt the operating sequence, press [Stop]. 7-32 Transmission applications C450...
Select the confidential box no. using [Print]. The document in the designated confidential user box will be printed out. Detail To interrupt operation, press [Close]. After you print a document received in a confidential box, the document is erased. C450 and then press 7-33...
Up to 8 digits can be entered for the password. Select the confidential box no. using lete]. The document held in the designated confidential box will be deleted. Detail To interrupt operation, press [Close]. 7-34 Transmission applications and then press [De- C450...
Polling TX (normal), polling RX (normal), confidential TX, polling RX (bul- letin), password TX Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. C450 Intermediate relay station Toll call Remote station Local call...
Page 178
To correct the wrong entry, use [Del.]. – Press [C] (clear) to clear the whole entry. Press [OK]. – To release the setting, press [OFF] or [Cancel]. The comm. setting screen will be restored. Press [OK]. The fax screen will be restored. 7-36 Transmission applications C450...
Page 179
See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. Press [Start]. The FK-502 stores the document in memory before starting transmis- sion. Detail To interrupt the operating sequence, press [Stop]. C450 7-37...
Polling RX (normal), polling TX (normal), V.34 OFF, polling RX (bulletin), polling TX (bulletin) Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Line Setting]. 7-38 Transmission applications C450...
Page 181
See “Selecting one destination” on page 3-21 for designating the destination. Set the original document. – See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. Press [Start]. The FK-502 starts transmission. C450 7-39...
Page 182
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. 7-40 Transmission applications C450...
G3 mode off. The V.34 mode will be resumed automatically on completion of transmission. Functions incompatible Polling RX (normal), polling TX (normal), ECM OFF Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Line Setting]. C450 7-41...
Page 184
Set the original document. – See “Placing originals on the platen glass” on page 3-8 for informa- tion about setting the document. Press [Start]. The FK-502 stores the document in memory before starting transmis- sion. 7-42 Transmission applications C450...
Page 185
To cancel transmission, see “Canceling transmission” on page 3-35. If the destination is not ready to receive, your call will be redialed. For in- formation about redialing, see “Manual redialing” on page 3-30. If transmission fails, refer to “Cannot send messages” on page 5-3. C450 7-43...
Press [Box] on the control panel to view the box screen, if it is not al- ready displayed. Select [System User Box] tab and [Memory RX User Box]. – When the user authentication function is set to [ON], [Personal User Box] tab is displayed. C450...
Page 190
When you want to display the next or previous screen, press To interrupt operation, press [Close] before pressing [Print]. Pressing [Proof Print] lets the first page in the selected file be printed out, allowing you to confirm the contents. Useful functions for reception and press [Print]. C450...
Select the received document using The designated document will print. Detail To interrupt operation, press [Close] before pressing [Print]. Pressing [Proof Print] lets the first page in the selected file be printed out, allowing you to confirm the contents. C450 and press [Delete].
When [Duplex Print (RX)] is set to [ON] When [Duplex Print (RX)] is set to [ON] in transmission/reception mode set- ting of the utility mode, documents are printed on both sides of the paper. For details, see “TX/RX setting” on page 11-37. Useful functions for reception C450...
The description below assumes use of the polled transmission, which uses the polling TX user box. Detail To use the bulletin board option, see “Bulletin” on page 9-9. For the printing or deleting method of the polled transmission docu- ments, see “User’s guide – Box operations”. C450...
TX, ECM OFF, confidential TX, password TX, polling TX (bulle- tin), polling RX (bulletin), relay TX req, V.34 OFF Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Polling TX]. Press [Normal]. Polling C450...
Page 197
Press [Start]. The FK-502 scans the document and holds it in memory until the des- tination sends a polling command, which causes transmission of the stored document. Detail If transmission fails, refer to “Cannot send messages” on page 5-3. C450...
It may be unable to be used with the other party machine. Refer to “Sequence polling RX reservation report” on page 12-26 and “Sequence polling reception report” on page 12-18 for information on the sequential polling reception reservation report and sequential polling re- ception result report. Polling C450...
Page 199
TX, relay TX req, ECM OFF, overseas TX, poll- ing TX (normal), password TX Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Polling RX]. Press [Normal]. C450...
Page 200
Your FK-502 starts to receive the document(s) set for transmission on the destination(s) or kept reserved for polled transmission. Detail To suspend polled reception before pressing [Start], press [Stop] on the control panel. If reception fails, see “Unable to receive” on page 4-6. Polling C450...
Detail For more information of the printing and removal methods of document on the bulletin board, see the “User’s guide – Network scanner opera- tions”. C450 Bulletin boards Browse Write Polling...
0 If a document is already saved to the bulletin board, the new one will overwrite the existing document. Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Polling TX]. 9-10 Polling C450...
Page 203
Set other functions if necessary. – See “Setting transmission conditions” on page 3-11 for information about setting functions in the fax screen. See “Application func- tions overview” on page 7-5 for information about setting functions in the fax application screen. C450 9-11...
Page 204
If you want to stop the FK-502 from reading the document after pressing [Start], press [Stop] and then press [Yes] on the confirma- tion screen. The FK-502 reads the document and places it in the bulletin board. 9-12 Polling C450...
You can receive by polling the document placed in a bulletin board of a des- tination. Perform the following procedure for this purpose. Press [Fax] on the control panel to view the fax screen, if it is not al- ready displayed. Press [Comm. Setting]. Press [Polling RX]. Press [Bulletin]. C450 9-13...
Page 206
Press [OK]. The fax screen will be restored. Select a destination. – See “Selecting one destination” on page 3-21 for more information. Press [Start]. The polling reception of the bulletin board of the other party machine starts. 9-14 Polling C450...
When the [Registering and Changing Address] of [Prohibit User Op- eration] in utility mode is set as [Restrict] or changing of the [One- Touch Registration] cannot be performed. For details of registering or changing the [One-Touch Registration], contact your administra- tor. C450 10-3...
- No registration is available when the name and the destination, e-mail ad- dress or box are not set. Detail You can confirm the registered information in the abbreviation list. For details of abbreviation list, refer to “Address book list” on page 12-32 C450 10-5...
Page 212
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Address Book], enter the “1” on the keypad. Press [Abbr. Dial]. 10-6 Registering/Settings C450...
Page 213
Multiple spaces can also be entered. A “P” is displayed on the screen. – [-] : This is entered as a separation symbol when dialing. It has no effect on dialing. A "-" is displayed on the screen. C450 10-7...
Page 214
– To stop registering, press [Cancel]. Registration is performed and the registered destination is displayed on a list. Press [Close]. When proceeding with the registration of the address book, go to step Press [Exit] on the sub-area. 10-8 Registering/Settings C450...
Page 215
Press [Address Book]. – In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Address Book], enter the "1" on the keypad. Press [E-Mail]. C450 10-9...
Page 216
Moves the cursor to the right. – [Delete] : The last character is cleared as it is pressed. – The e-mail address can be up to 320 characters. – Press [C] (clear) to delete all of the entries that have been made. 10-10 Registering/Settings C450...
Page 217
Press [OK]. – To stop registering, press [Cancel]. Registration is performed and the registered destination is displayed on a list. Press [Close]. When proceeding with the registration of the address book, go to step Press [Exit] on the sub-area. C450 10-11...
Page 218
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Address Book], enter the "1" on the keypad. Press [User Box]. 10-12 Registering/Settings C450...
Page 219
Press [Name] and then enter the name of address book. – For the operation of the entering character, see page 13-4. – The name can be up to 24 characters. – In [No.], an unused number is displayed. Press [User Box Name]. C450 10-13...
Page 220
– To stop registering, press [Cancel]. Registration is performed and the registered destination is displayed on a list. Press [Close]. When proceeding with the registration of the address book, go to step Press [Exit] on the sub-area. 10-14 Registering/Settings C450...
Page 221
Press [Abbr. Dial] or [E-Mail] or [User Box]. Press the address book you want to change and press [Edit]. Press the item you want to change and change its contents in the screen displayed, and then press [OK]. C450 10-15...
Page 222
Confirm the information you have changed and press [OK]. – To stop changing, press [Cancel]. When proceeding with the change, go to step 5. Press [Close]. Press [Exit] on the sub-area. 10-16 Registering/Settings C450...
Page 223
Press [Abbr. Dial] or [E-Mail] or [User Box]. Press the address book you want to delete and press [Delete]. Press [Yes] in the delete confirmation screen displayed. – To stop deleting, press [No]. When proceeding with the deleting, go to step 4. C450 10-17...
Page 224
Press [Close]. Press [Exit] on the sub-area. 10-18 Registering/Settings C450...
- No registration is available when the name and the destination, e-mail ad- dress or box name are not set. Detail You can confirm the registered information in the group destination list. For details of group destination list, refer to “Group address list” on page 12-35. C450 10-19...
Page 226
"2" on the keypad. Press [New]. – When the group has been already registered, you can change the entries at this point by pressing [Edit]. For details, see page 10-23. – Only the groups registered in [Fax] are displayed. 10-20 Registering/Settings C450...
Page 227
Up to 500 address books can be registered for each group. Select a category in which the address book is registered that is to be registered in the group from among [Abbr. Dial], [User Box] and [E-Mail Address]. C450 10-21...
Page 228
Pressing displayed. Press [OK]. Press [Close]. Press [OK]. When proceeding with the registration of group, go to step 5. Press [Exit] on the sub-area. 10-22 allows you to scrawl the key of the number to be Registering/Settings C450...
Page 229
Select an item to change and then change a setting on the displayed screen, and press [OK] or [Close]. Confirm the information you have changed and press [OK]. – To stop the changing, press [Cancel]. Press [Exit] on the sub-area. C450 allows you to change the page to be dis- 10-23...
Page 230
Press [Yes] in the delete confirmation screen displayed. – To stop deleting, Press [No]. When proceeding with the deleting, go to step 3. Press [Close]. Press [Exit] on the sub-area. 10-24 allows you to change the page to be dis- Registering/Settings C450...
Press [Program]. – In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Program], enter the "3" on the keypad. C450 10-25...
Page 232
For the operation of the entering character, see page 13-4. – The name can be up to 24 characters. 10-26 Not registered (Space) in the left-hand side of [Page List], you can in the right hand side of list, the next pro- Registering/Settings C450...
Page 233
100. Press the number key that is conform- ity with the number of the address book registered to display the address book. Pressing displayed. – Press [OK]. C450 allows you to scrawl the key of the number to be 10-27...
Page 234
For details of [Scan Setting], [Comm. Setting], see “Transmission applications” on page 7-3. Press [Close]. – To stop registering, press [Cancel]. When proceeding with the registration of the program, go to step 3. Press [Exit] on the sub-area. 10-28 Registering/Settings C450...
Page 235
If you press [Page List], you can specify the display of a program list per page. – If you press arbitrary key in the page list screen, you can change the page name it is displayed. C450 in the left-hand side of [Page List], you can 10-29...
Page 236
Press [Yes] in the delete confirmation screen displayed. – To stop deleting, press [No]. When proceeding with the deleting, go to step 3. Press [Exit] on the sub-area. 10-30 in the right hand side of list, the next pro- Registering/Settings C450...
Press [Subject/Text for E-mail]. – In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. C450 10-31...
Page 238
Press [Subject]. Press [New]. Press [Subject]. – The entry of up to 64 characters is available for [Subject] of [Sub- ject/Text for E-mail]. – In [No.], an unused number is displayed. 10-32 Registering/Settings C450...
Page 239
Press [OK]. – To stop registering, press [Cancel]. Registration is performed and the registered destination is displayed on a list. Press [Close]. When proceeding with the registration of the subject, go to step 4. Press [Exit] on the sub-area. C450 10-33...
Page 240
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Subject]. 10-34 Registering/Settings C450...
Page 241
– To stop registering, press [Cancel]. The subject is changed. Press [Close]. When proceeding with the change of the subject, go to step 4. Press [Exit] on the sub-area. C450 allows you to change the page to be dis- 10-35...
Page 242
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Subject]. 10-36 Registering/Settings C450...
Page 243
– To stop deleting, press [No]. The subject is deleted. Press [Close]. When proceeding with the delete of the subject, go to step 4. Press [Exit] on the sub-area. C450 allows you to change the page to be dis- 10-37...
Page 244
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Subject]. 10-38 Registering/Settings C450...
Page 245
Registering/Settings Select the subject you want to default and then press [Set as Default]. Press [Close]. Press [Exit] on the sub-area. C450 10-39...
Page 246
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Text]. 10-40 Registering/Settings C450...
Page 247
Press [OK]. – To stop registering, press [Cancel]. Registration is performed and the registered destination is displayed on a list. Press [Close]. When proceeding with the registration of the text, go to step 4. Press [Exit] on the sub-area. C450 10-41...
Page 248
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Text]. 10-42 Registering/Settings C450...
Page 249
– To stop registering, press [Cancel]. The text is changed. Press [Close]. When proceeding with the change of the text, go to Step 4. Press [Exit] on the sub-area. C450 allows you to change the page to be dis- 10-43...
Page 250
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Text]. 10-44 Registering/Settings C450...
Page 251
– To stop deleting, press [No]. The text is deleted. Press [Close]. When proceeding with the delete of the text, go to step 4. Press [Exit] on the sub-area. C450 allows you to change the page to be dis- 10-45...
Page 252
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Subject/ Text for E-mail], enter the "4" on the keypad. Press [Text]. 10-46 Registering/Settings C450...
Page 253
Registering/Settings Select the text you want to default and then press [Set as Default]. Press [Close]. Press [Exit] on the sub-area. C450 10-47...
10.6 Setting the confidential boxes The public / personal box which the box extension function attached is used as a confidential box. The confidential communication which used the F-code can be used in this machine. In order to perform the confidential reception, it is necessary to set up a user box no., name, password, index, and type.
Page 255
Originating station Specifies a confidential user box and trans- mits. A box number and confidential password initi- ate transmission of a fax document. C450 Receiving station Opens confidential user box to receive the document. The document received stored the specified confidential user box.
For the operations of the bulletin board, see page 9-9. 10-50 Registering/Settings Receiving station Receives the document by polling by spec- ifying the bulletin board. The box no. should be specified to receiving by polling. Registering a bulletin board. C450...
RX box. Detail For the printing method of memory RX user box, refer to “Memory recep- tion” on page 8-3 For the registration method of the memory RX user box, see "User’s guide – Box operations". C450 10-51...
The procedures for entering in and exiting the utility mode and setting fax functions are described below. 11.1.1 Entering user setting Entering user setting Press [Fax] and press [Utility/Counter] on the control panel. Press [User Setting]. C450 11-3...
Press [Fax] and press [Utility/Counter] on the control panel. Press [Administrator Setting]. Enter the password and press [OK]. Detail The password for the administrator can be changed in [Security Setting]. The administrator should have a responsibility for the management of the password. C450 11-5...
[Factory Default]: Values set when shipped from the factory are registered as the default of fax function. C450 Available value Program / Group / Ad- dress Book / Direct Input...
Available value Normal / Immediately Available value Batch Print / Page Print Available value Allow / Restrict Available value Up to 30 in characters and symbols. Up to 20 characters with 0 to 9, +, space, * and # used. C450...
Set the sound volume of the speaker. Sound Volume The displays are different depending on the country. The line which can be set up is different depending on the country. C450 Available value Inside Body Text / Outside Body Text...
Boxes on the hard disk. TSI User Box Set- This is a function to allocate received ting originals according to the TSI information of faxes received. C450 Available value / OFF / OFF ON/ OFF ON / OFF / Forward & Print / For- ward &...
This prefix will be dialed when external line option is selected with abbreviated dial number or Program. 11-12 Utility mode Available value ON / OFF When set to ON, the number is of the outside line. C450...
Indicates factory default setting. 11.2.14Job Settings List Administrator Setting >> Fax Setting >> Job Settings List Detail For details, see page 12-44 C450 Available value / Daily / Every 100 Comm. / 100/Daily ON / If TX Fails / OFF...
Display * Indicates factory default setting. 11-14 Utility mode Available value Program / Group / Ad- dress Book / Direct Input Temporary One-Touch / PAGE1 - PAGE27 Main / ABC - etc / OFF 14 char. / 24 char. C450...
Page 273
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Display Setting], enter 2 through the numeric keypad. Press [Fax Basic Screen Default Setting]. C450 11-15...
Page 274
Select the item you wish to set. – When you want to stop the setting, press [Exit] in the sub-area. Select the parameter you wish to set. Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. 11-16 Utility mode C450...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Initial Set- ting], enter 3 through the numeric keypad. C450 Available value Current Setting / Factory...
Page 276
Press [Factory Default] and then press [OK]. – When you want to stop the setting, press [Cancel] Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. 11-18 Utility mode C450...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Display Setting], enter 2 through the numeric keypad. C450 Available value ON / OFF ON / OFF...
Page 278
Press [Fax Active Screen]. Select [Transmission Display] or [Receipt Display]. – When you want to stop the setting, press [Exit] in the sub-area. Select the parameter you wish to set. 11-20 Utility mode C450...
Page 279
Utility mode Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. C450 11-21...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [System Setting], enter 1 through the numeric keypad. 11-22 Utility mode Available value Normal / Immediately C450...
Page 281
Utility mode Press [Power Save]. Press [Entering Power Save Mode (Fax)]. Select the parameter you wish to set. C450 11-23...
Page 282
Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. 11-24 Utility mode C450...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [System Setting], enter 1 through the numeric keypad. C450 Available value Batch Print / Page Print...
Page 285
When the [Duplex Print (RX)] is set to the [ON], the print is made af- ter receiving the data for both sides (for 2 pages). Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. C450 11-27...
In the case of [Fax Set- ting], enter 8 through the numeric keypad. 11-28 Utility mode Available value Up to 30 in characters and symbols. Up to 20 characters with 0 to 9, +, space, * and # used. C450...
Page 287
See “Entering text” on page 13-4 for more information. Enter the sender fax number by using keypad, +, space, – Represents “+”. – Space: Represents a space. – Moves the cursor to the left. – Moves the cursor to the right. C450 11-29...
Page 288
When you want to stop the setting, press [Cancel]. – To correct the entry, press [C] (clear) on the control panel. Press [OK] and then press [Close]. The sender fax no. and sender name you have entered is registered. Press [Exit] on the sub-area. 11-30 Utility mode C450...
The information identifying the originating station, which can be printed on the reproduced pages at the receiving station, is both of the fax ID and the name. For details, refer to “Sender information” on page 3-53. C450 Available value Inside Body Text:...
Page 290
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Header/Footer Position]. 11-32 Utility mode C450...
Page 291
Select the item you wish to set. – When you want to stop the setting, press [Exit] in the sub-area. Select the parameter you wish to set. Press [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. C450 11-33...
The line which can be set up is different depending on the country. Indicates factory default setting. 11-34 Utility mode Available value / 10pps Auto RX / Manual RX 0-15 (2 times 0-7 (3 times 1-15 (3 min. ON / OFF 0-31 (16 C450...
Page 293
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Telephone Line Setting]. C450 11-35...
Page 294
Sound Volume] and then [Lower] or [Higher] to set the level, and fi- nally press [OK]. Press [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. 11-36 to go to the next or previous screen. Utility mode C450...
The displays are different depending on the country. To make the setting of [Print Paper Size] enable, set [Tray Selection for RX Print] to [Auto]. Tray type may be different depending on the installed option. C450 Available value / ON...
Page 296
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [TX/RX Setting]. 11-38 Utility mode C450...
Page 297
When you want to stop the setting, press [Exit] in the sub-area. Select the parameter you wish to set. Press [Close]. The value of the parameter is changed. Close [Exit] on the sub-area. C450 to go to the next or previous screen. 11-39...
7-30. Selecting “OFF” both relay transmis- sion request and relayed transmis- sion to multiple stations are disabled. For details of relayed communica- tion, see “Relay transmission re- quest” on page 7-35. Utility mode Available value / OFF / OFF C450...
Page 299
Utility mode Press [Function Setting]. Press [Function ON/OFF Setting]. Select the item you wish to set. – When you want to stop the setting, press [Exit] in the sub-area. C450 11-41...
Page 300
Select the parameter you wish to set. Press [Close]. – The value of the parameter is changed. Press [Exit] on the sub-area. 11-42 Utility mode C450...
Setting the memory RX to ON makes it impossible to select the fax RX setting, the TSI user box setting and the forward TX setting option. To print the document received in memory reception mode, see “Memory reception” on page 8-3. C450 Available value ON / OFF Set a password within an 8- digit.
Page 302
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. 11-44 Utility mode C450...
Page 303
If you press [C] (clear) the information you have entered will be de- leted. – When you want to stop the setting, press [Cancel]. Press [OK] and then [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. C450 11-45...
The closed area reception is the function used to receive the incoming data only when the sender's password is valid. * Indicates factory default setting. 11-46 Utility mode Available value ON / OFF The password is a number of up to 4 digits. C450...
Page 305
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. C450 11-47...
Page 306
If you press [C] (clear) the information you have entered will be de- leted. – To exit, press [Cancel]. Press [OK] and then [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. 11-48 Utility mode C450...
Detail Setting the forward TX setting to [Forward & Print] or [Forward & Print (If TX Fails)] makes it impossible to select the TSI user box setting option. C450 Available value / Forward & Print / For- ward & Print (If TX Fails)
Page 308
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. 11-50 Utility mode C450...
Page 309
Forward & Print The received document is transferred and printed by this machine as well. – Forward & Print (If TX Fails) The received document is transferred. If the transfer failed, the document is printed by this machine. C450 11-51...
Page 310
If you press [C] (clear) the information you have entered will be de- leted. – When you want to stop the setting, press [Cancel]. Press [OK] and then [Close]. The setting is changed and you return to the utility mode screen. Press [Exit] on the sub-area. 11-52 Utility mode C450...
You can confirm the confidential access protect numbers defined. Item Description Confidential RX You can confirm the confidential access Password Check numbers defined. Detail For the registration of confidential access protect numbers, see “Setting the confidential boxes” on page 10-48. C450 Available value 11-53...
Page 312
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. 11-54 Utility mode C450...
Page 313
Utility mode Press [Confidential RX Password Check]. Select the confidential box you wish to confirm. – Press [Close]. Press [Exit] on the sub-area. C450 to go to the next or previous screen. 11-55...
RX and the TSI user box setting option. The fax-receiving documents are stored in the TIFF format at fixed box or specified box or sender (TSI) RX box. 11-56 Utility mode Hard disk Available value ON / OFF Fixed Box / Specified Box C450...
Page 315
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. C450 11-57...
Page 316
Press [Fax RX Setting]. Select [ON] for [Fax RX Setting]. – The displays are different depending on the country. – OFF: The PC-fax RX feature is not available. – The PC-fax RX feature is made when either of the fax number and the PC-fax number is received, and a document received is stored in the specified box.
Page 317
Utility mode Press [OK] and then press [Close]. The setting is changed and you return to the utility mode screen. C450 11-59...
TSI information of faxes received. Detail Setting the TSI user box setting to ON makes it impossible to select the memory RX, forward TX setting and fax RX setting option. 11-60 Utility mode Hard disk Available value ON / OFF C450...
Page 319
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Function Setting]. C450 11-61...
Page 320
Select a number you want to register, and press [Edit]. – If you want to delete a distribution, select a distribution, you want to delete, and press [Delete]. – You can register up to 128 boxes. – 11-62 to go to the next or previous screen. Utility mode C450...
Page 321
You can enter the box no. in the range of 1 to 999999999. Press [OK] and then press [Close]. The TSI RX user box is set. Press [Exit]. The fax RX distribution screen will be restored. C450 to input fax ID in 11-63...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. 11-64 Utility mode Available value ON / OFF 0-9999 C450...
Page 323
If you press [C] (clear) the information you have entered will be de- leted. – When you want to stop the setting, press [Cancel]. Press [OK] and then press [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. C450 11-65...
ON / If TX Fails / OFF ON / OFF ON / OFF ON / OFF ON / OFF All Dest. / 1 Dest. at a time Tray 1 / Tray 2 / Tray 3 / Tray 4 / Bypass Tray / ON C450...
Page 325
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. Press [Report Settings]. C450 11-67...
Page 326
When you want to stop the setting, press [Exit] in the sub-area. Select the item you wish to set. Press [Close]. The value of the parameter is changed. Press [Exit] on the sub-area. 11-68 to go to the next or previous screen. Utility mode C450...
Reservation communica- tion report Reservation polling TX re- port Broadcast reserved report C450 Explanation This report contains a record of transmissions and receptions. Communications for a total of 100 transmissions and receptions are recorded on separate pages for transmission and reception.
Numbers registered for address book can be printed out. Numbers registered for program can be printed out. Numbers registered for group can be printed out. The list of the subject/text (for e-mail) can be printed out. Settings made with utility mode can be printed out. C450...
The interval at which the activity report is printed out can be set with report settings. 12.2.2 Manual printout The activity report can be printed out manually with the following procedure. Manual printout Press [Job List] on the fax screen. Press [Fax TX] tab. Press [Job History]. C450 12-5...
Page 332
Press [Comm. Setting]. Press [Activity Report], [TX Report] or [RX Report]. Press [Print]. The report is printed out. 12-6 Explanation of reports and lists C450...
Page 333
No.: Destination: Start Time: Time: Prints: C450 Description Serial numbers are assigned to each transmission and reception. The following is indicated. This space is left blank when there is no infor- mation. • Name when name is registered in abbreviated dialing entry list •...
Page 334
(shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase MIX: Mixed size original CALL: Telephone CSRC: CS remote care FWD: FORWARD PC-fax BND: Bind position Special original FCODE: F-code setting MBX: Confidential BLTN: Bulletin board C450...
Automatic printout can be set to [ON], [If TX Fails] or [OFF] with [TX Report] at [Report Settings] of utility mode. For details, see “Report settings” on page 11-67. The actual reports may be different from the reports in this manual. C450 12-9...
Page 336
No Ans Shown when the destination being called did not answer. Busy Shown when unable to complete communication due to the line being busy. M-Full Memory-full is shown when the fax file memory became full during reception and reception failed. C450...
Page 337
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
No Ans Shown when the destination being called did not answer. Busy Shown when unable to complete communication due to the line being busy. M-Full Memory-full is shown when the fax file memory became full during reception and reception failed. C450...
Page 339
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
No Ans Shown when the destination being called did not answer. Busy Shown when unable to complete communication due to the line being busy. M-Full Memory-full is shown when the fax file memory became full during reception and reception failed. C450...
Page 341
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
The time at which communication started is shown. The required time for the communication is shown. The number of pages transmitted is shown. The number of pages able to be transmitted and the total number of pages are shown in the form of a fraction. C450...
Page 343
Explanation of reports and lists Item Result: Note: C450 Description Shown when communication ended normally. S-OK Shown when communication was stopped. PW-OFF Shown when the power switch is turned off. Shown when there has been an incoming tele- phone call.
No Ans Shown when the destination being called did not answer. Busy Shown when unable to complete communication due to the line being busy. M-Full Memory-full is shown when the fax file memory became full during reception and reception failed. C450...
Page 345
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
• Name when name is registered in abbreviated dialing entry list • Telephone number or mail address of destination The time that is reserved for transmission. The designated time is shown in the case of timer transmission. The number of original pages scanned is shown. C450...
Page 347
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
The actual reports may be different from the reports in this manual. Item Destination: Create time: Start Time: Prints: 12-22 Explanation of reports and lists Description Not shown. The time that is reserved for transmission. Not shown. The number of original pages scanned is shown. C450...
Page 349
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
• Telephone number of destination when the destination has been se- lected with the keypad. The time at which the transmission was reserved is shown. The designated time is shown in the case of timer transmission. The number of original pages scanned is shown. C450...
Page 351
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
Prints: 12-26 Explanation of reports and lists Description The telephone number of the destination. The time at which polling is received. The designated time is shown in the case of timer transmission. The number of pages transmitted is shown. C450...
Page 353
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
No Ans Shown when the destination being called did not answer. Busy Shown when unable to complete communication due to the line being busy. M-Full Memory-full is shown when the fax file memory became full during reception and reception failed. C450...
Page 355
Explanation of reports and lists Item Note: C450 Description Any of the following remarks may be shown. TMR: Timer communication POL: Polling TRN: Turn-around (shown when the turn-around is executed from a destination) ORG: Original size set FME: Frame erase...
The following is shown. • Destination name when destination name is registered in abbreviated dialing • Telephone number of destination. The time at which communication started. The required time for the communication is shown. The number of pages transmitted. C450...
Page 357
Explanation of reports and lists Item Result: Note: C450 Description Shown when communication ended normally. S-OK Shown when communication was stopped. PW-OFF Shown when the power switch is turned off. Shown when there has been an incoming tele- phone call.
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [One-Touch Registration], enter 3 through the numeric keypad. Press [One-Touch Registration List]. Press [Address Book List]. 12-32 Explanation of reports and lists C450...
Page 359
The address book list is printed out. Detail When no necessary paper is set in the paper tray, [Start] flashes in red. On an occasion like this, [Start] cannot be pressed. C450 moves the cursor to the left and pressing moves it 12-33...
Page 360
The actual reports may be different from the reports in this manual. Item No.: Name: Dial Number: Line Setting 12-34 Explanation of reports and lists Description Abbreviated dialing number. Registration name Registration fax number for address book is shown when line setting is appointed. C450...
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [One-Touch Registration], enter 3 through the numeric keypad. Press [One-Touch Registration List]. Press [Group List]. C450 12-35...
Page 362
When no necessary paper is set in the paper tray, [Start] flashes in red. On an occasion like this, [Start] cannot be pressed. 12-36 Explanation of reports and lists moves the cursor to the left and pressing moves it C450...
Page 363
The actual reports may be different from the reports in this manual. Item No.: Name: Addr. No.: Regist Count: C450 Description Registration group number Registration group name Abbreviated dialing numbers registered for the group Number of abbreviated dialing numbers registered for the group.
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [One-Touch Registration], enter 3 through the numeric keypad. Press [One-Touch Registration List]. Press [Program List]. 12-38 Explanation of reports and lists C450...
Page 365
The program list is printed out. Detail When no necessary paper is set in the paper tray, [Start] flashes in red. On an occasion like this, [Start] cannot be pressed. C450 moves the cursor to the left and pressing moves it 12-39...
Page 366
No.: Name: Dail Number: User Box Number: E-Mail Address: Item: Setting: 12-40 Explanation of reports and lists Description Registration program number Registration name Registration dial number Registration user box number Registration e-mail address Functions of the FK-502. Setting status. C450...
– In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [One-Touch Registration], enter 3 through the numeric keypad. Press [One-Touch Registration List]. C450 12-41...
Page 368
Select tray to print. Press [Start]. The subject/text list is printed out. Detail When no necessary paper is set in the paper tray, [Start] flashes in red. On an occasion like this, [Start] cannot be pressed. 12-42 Explanation of reports and lists C450...
Page 369
Explanation of reports and lists How to see the subject/text list List name Subject List Text List C450 Item Description No.: Registration number. Subject: Subject registered for the subject/text (for e- mail). No.: Registration number. Text: Text registered for the subject/text (for e-mail).
In the utility mode, it is also possible to enter a number displayed in the key through the keypad for selection. In the case of [Fax Set- ting], enter 8 through the numeric keypad. 12-44 Explanation of reports and lists C450...
Page 371
Press [Job Settings List]. Select tray to print. Press [Start]. The fax settings list is printed out. Detail When no necessary paper is set in the paper tray, [Start] flashes in red. On an occasion like this, [Start] cannot be pressed. C450 12-45...
Page 372
How to see the fax setting list The actual reports may be different from the reports in this manual. Item Item: Setting: 12-46 Explanation of reports and lists Description Item of utility mode. Setting status. C450...
Page 373
Explanation of reports and lists The actual reports may be different from the reports in this manual. C450 12-47...
The actual reports may be different from the reports in this manual. Item Name Password Class 12-48 Explanation of reports and lists Description Box number registered with confidential / bulletin board. Registered name. Confidential password. Confidential or bulletin board is displayed. C450...
12.18.2Sender (TSI) RX box The actual reports may be different from the reports in this manual. Item Sender (TSI) Box No. C450 Description The registration number of the sender (TSI) RX The registered sender information. The registered box no. 12-49...
Page 376
Explanation of reports and lists 12-50 C450...
Detail Memory overflow may occur when the original document is being read. In this case, you can either transmit the part of the original that has been read, or redo the procedure from the beginning. C450 13-3...
The keypad can also be used to type in numbers. Any of the following keyboards may appear. Example Password input screen E-mail address input screen E-mail message input screen 13-4 Appendix C450...
Page 381
Appendix The following procedure describes how to type using e-mail address input screen. C450 13-5...
Page 382
To change a character in the entered text, touch the cursor to the character to be changed, touch [Delete], and then type in the desired letter or number. List of available characters Type Available characters Alphanumeric characters / symbols 13-6 Appendix to move C450...
Confidential com- munication Dialing method ECM (Error Correc- tion Mode) C450 Description The function to gather two pages into one page and to transmit the composed wide page. One of the functions to register the fax numbers dialed fre- quently. Registering the destination name and retrieval character when you register the abbreviated dial, you can designate the destination with the Address Book.
Page 384
The function to set and send document pages of mixed sizes by a single sequence of operations. Appendix C450...
Page 385
Relaying station Reserving transmis- sion Resolution Restransmission C450 Description The function to designate the paper size for the document to be sent. Normally, when the paper size loaded at the destination is too small to accommodate the image being transmitted, the original image will be reduced to fit the paper size.
Page 386
The function to determine the document sizes before reading and sending the original. Some facsimiles cannot detect the document size if it has been folded. This func- tion is available only when reading the original with the ADF. Appendix C450...
Confidential communication .. 7-30 Confidential RX password check ... 11-53 Confidential RX report ... 12-28 Confidential/Bulletin list ... 12-48 Contrast dial ...2-5 C450 Control panel ... 2-4 Copy ... 2-4 Crosswise ... 1-23 3-27 Data ... 2-5 Density ... 3-13 Destination indicator ...
Page 388
Polling TX user box ...2-20 Print separate fax page 4-12 10-51 Print/Fax output settings ...11-8 3-19 Program . 2-12 Program list ...12-38 Proof copy ...2-5 Public user box ...2-19 Quick memory TX ...3-42 Appendix 7-27 3-10 4-13 11-25 2-15 3-22 10-25 C450...
Page 389
Stop ...2-5 Sub area ... 2-16 SUB POWER ...2-5 Subject ... 10-31 Subject/Text list ... 12-41 System user box ... 2-20 C450 Telephone line settings ... 2-7 Text ... 10-31 Timer TX ... 3-47 To type text ... 13-6 11-67 Tone ...