Console Overview; Key Function; Display Description; How To Start - Horizon Fitness Andes 2 User Manual

ANDES 2 CONSOLE
A. K E Y F UN CT IO N
CONTROL MODE
MANUAL / PROGRAM
USER
RPM / SPEED
DISTANCE
PROGRAMS
-
(P1 P12)
RESET:
Press reset
function value.
START / STOP
RECOVERY
B..DIS PL A Y DE S CR I PT IO N
DISPLAY
SET
ITEM MEMORY
SCOPE SCOPE
1~16
MANUAL LEVEL
(±1LEVEL)
PROGRAM P1~P12 1~12
USER
U1~U4
(PROGRAM)
0:00~99:59 0:00~99:0 0
±1 MINU
TIME MINU SEC
CIRCUIT
MINU SEC
8
USER
SEX
PULSE
CALORIES
ROTARY / PUSH KNOB:
ENTER - confirm function value

+ UP : Choose Control Mode &

Increase function value
DOWN : Choose Control Mode &

decrease function value
SIMPLE ILLUMINATION
RESET
Y N Set up Resistance-Load from Level 1-16
1. P1～P12，12 fixed diagram.
2. Every time you choose one PROGRAM, correspondent
diagram will display on the centerof dot matrix.
3.Diagram choice by turning UP、DOWN-Knob，and ENTER
Y N
for confirmation.
4.After selecting program, blinking diagram will show in
dot matrix, turning UP/DOWN-KNOB for adjusting LEVEL
and ENTER -KEY for TIMEsetting，TIME symbol blinks.
1.USER can set PROGRAM diagram by himself
2. Press ENTER KEY for line setting and UP、DOWN Knob
N
Y
for adjusting LOAD level.
3. One saved value each.
1. Count UP TIME value when start exercise, no seating.
Y Y
2.If setting, when count down to 0,system will STOP
TIME value blinks
SPEED 0.0~99.9 km/h N N
0~15~99 N N
RPM
0.00~99.9
0.00~99.99
0
DISTANCE KM(ML) Y
±0.1
CIRCUIT
0~990
CALORIES 0~999 CAL ±10 in
Y
circ uit
GENDER Y
AGE 10 - 25 -99 ±1 Y
100 -160 200
-
(CM) ±1 Y
HEIGHT
40 -60 -80 (INCH)
20-50-150 (KG)
Y
WEIGHT ±1
40-100-350 (LB)
N N
HEART SYMBOL ON/OFF blink
C .H O W T O ST AR T
1. POWER ON
Make sure plug in right power adaptor (6V / 500mA), and regarding with different country system pin, and
then powering on: BI with long tone for 1 second together with LCD full display for 2 seconds.
2. PRE-SET USER/ AGENDA / AGE / HEIGHT / WEIGHT
User inputting his/her real user data (sex / age/ height / weight) into computer to stove it to be used in
calculated reference.
3. SELECT MANUAL/PROGRAMS/ USER
User can choose different control mode to start his work out. See below is main description of each control mode.
4. EXECUTE MANUAL / PROGRAMS/ USER
Execute selected control mode.
5. PRE-SET TIME / DISTANCE / CALORIES / HEART RATE
Setting and inputting user wanted function value of above, the function value of display will count down to zero;
or user can not inputting these, just forget setting value, computer will know your workout is from 0 to end value.
6. PRESS ENTER/UP/DOWN
Use UP / DOWN key to increase / decrease function value.
After setting each function value to press "ENTER" to confirm your setting
7. TEST RECOVERY
Press RECOVERY , the computer will calculate your recovery value on display regarding with your user data and
actual workout function value.
N Display actually workout speed.
N Display actually workout RPM.
1. Count UP DISTANCE value when start exercise, no seating.
Y
2.If setting, when count down to 0,system will STOP .
1. Count UP CALORIES value when start exercise, no setting
Y
2.If setting, when count down to 0,system will STOP .
N Under setting GENDER, please choose GIRL or BOY
N Under setting "AGE", initial value is 25.
Under setting Height"H.T", initial value160CM(60INCH)
N
Under setting Weight: "W.T", initial value.
N
50KG(100LB)
1. Display with blink as per Heart Rate Hi / Fast & Low slow.
N
2. No Heart-Rate detected SYMBOL will be gone.
9