Table of Contents
Advertisement
WI1502A 9/06
TOUCHPAD MENU MODE
ALL MESSAGES
IN MENU
ENTER BYPASS
MENU
Y/N
DISPLAY
ZN DIRECTORY
Y/N
BYPASS
OPEN ZONES?
Y/N
DISPLAY
ZN BYPASSED
Y/N
ACTIVATE
CHIME
Y/N
CHANGE KEYPAD
BEEP VOLUME
Y/N
CHANGE VOICE
VOLUME
Y/N
ACTIVATE
SIREN TEST
Y/N
DISPLAY
FIRE ALARM
Y/N
DISPLAY
FIRE TROUBLE
Y/N
ACTIVATE
FAULT FIND
Y/N
RESET
SYSTEM TBL
Y/N
ACTIVATE
DIALER TEST
Y/N
ENTER LOG
MENU
Y/N
DISPLAY
ALARM LOG
Y/N
DISPLAY
TOTAL LOG
Y/N
DISPLAY
FIRE LOG
Y/N
DISPLAY
SYSTEM LOG
Y/N
ACTIVATE
PROGRAM
Y/N
CHANGE DATE
Y/N
CHANGE TIME
Y/N
ENROLL
MASTER IFOB
Y/N
ENROLL
USER I-FOB
Y/N
DELETE
I-FOB
Y/N
ACTIVATE
DOWNLOAD
Y/N
ACTIVATE
Y/N
LOST KEY MODE
ACTIVATE
Y/N
PIR TEST
L
NAPCO Security Systems
NOTES
When bypassing a zone, press BYPASS to enter this menu.
Allows individual zones to be bypassed. Press Yes or No to
scroll through zone list.
Disables monitoring of all faulted zones EXCEPT the PRI-
MARY Touchpad door.
Scrolls list of bypassed zones (cannot unbypass from this
selection).
When activated, this selection reads "DEACTIVATE
CHIME Y/N".
Selections are LOW (default), MED, MED-HIGH, HIGH, and
OFF (tactile or entry warning only).
Selections are LOW, MED, MED-HIGH (default), HIGH,
OFF (voice prompt volume).
Press YES to activate burg relay output for 2 seconds.
Displays list of shorted fire zones only when a fire alarm is
tripped.
Displays list of opened fire zones only when a fire trouble
(open on a fire zone is detected.
Activates Fault Find mode. The Master I-FOB MUST be
inserted into the Touchpad for this menu item to appear.
This message appears if a trouble is found.
Test Timer must be programmed or this option will not appear.
Displays most recent alarm events.
Displays most recent events of all types.
Displays most recent fire events.
Displays most recent system events.
Also called "User Program Mode". See Touchpad User Man-
ual for more information.
The Master I-FOB is programmed at the factory to be the
USER 01 ID code in all Areas. With the Master I-FOB, addi-
tional User I-FOB's may be created for any Areas.
The Master I-FOB MUST be inserted into the Touchpad
(when prompted) to allow the creation of a User I-FOB.
See Touchpad User Manual for more information.
Allows modem connection with PC Preset software.
If the lost key mode is set to be ON, an I-FOB will be required
to disarm the system when entering the through any moni-
tored door.
When activated, this selection reads
"DEACTIVATE LOST KEY MODE
Key Mode" appears in the LCD Window with the "System
Ready" message.
The Master I-FOB MUST be inserted into the Touchpad for
this menu item to appear. (Press MENU to skip to the top of
the list).
The Touchpad can provide access to a wide assortment
of utility functions, each displayed on the Touchpad LCD
window in a prompting "YES/NO" format. This Touchpad
menu is not necessary for panel programming, but is in-
cluded here for reference.
TYPICAL USER: Homeowner.
TYPICAL INTERFACE: Touchpad only.
HOW TO ENTER: At the installed Touchpad, insert the
Master I-FOB and press MENU to enter. All mes-
sages in the Touchpad Menu Mode are listed be-
low, but some messages may not appear in the
Touchpad display unless a User or Master I-FOB is
inserted in the Touchpad; if the required condition is
not present; or if the F-64 control panel is configured
in such a way as to remove the message from this
Menu. For example, "DISPLAY ZN FAULTS Y/N"
will only display if zones are faulted. With each mes-
sage, press YES to proceed with the change or NO
to skip to the next selection. Note: Highlighted mes-
sages are sub-menu selections.
Y/N", and "Lost
Freedom F-64 Programming Instructions
Page 43
Advertisement
Table of Contents
