If A Menu Screen Appears - Alpine IVA-D106 Owner's Manual

Menu Operations
c:QVi?P
~
Touch [RETURN] to return to
the previous display.
(Operation may not be
possible, depending on the
disc.)
2 Select a desired menu item by touching [,6], [oy]. [.... ] or
[~].
3 Touch [ENTER] to confirm the selected item.
On DVDs and Video CDs with playback control (PBC). menu screens
may appear automatically. If this happens. perform the operation
described below to start playback.
• To play back a DVD-Audio disc. set "VCAP" in "Setting the DVD-
Audio Playback Mode" (page 34).
Direct Menu Operations
~ c.QVi?3?
1 Touch the DVD menu directly.
• Some operations cannot be peiformed depending on the disc.
"
..
~
~l
·,····1
" , " ' " .. 1
. ~ " " " ' " ~ . ,
" - - - - .
_ ~--'--
. . • . . .
·····l~J
Touch [KEY].
The menu operation mode will be displayed.
~"-:---~--··~------ji=miii.01
If
a
m~nu
screen, appears
• Play Position Memory Function
Even if you turn power off or switch the Ignition Key
to OFF during playback or change the source,
playback will continue from the point where
playback stopped when the power is turned ON
again.
ffiCaution
• Not all functions will operate for every
ovo.
See the
individual OVO's instructions for details on the
features supported.
• Fingerprints on a disc may adversely affect
playback. If a problem occurs, remove the disc and
check for fingerprints on the playback side. Clean
the disc if necessary.
• If you switch the power or Ignition Key OFF or
change sources during playback, playback will
continue where you left off when you resume
playback.
• If you try to perform an invalid operation (based on
the type of disc being played), the following mark is
displayed on the monitor screen:
(S)
• The operation screen changes to the visual screen in the DVD or
Video CD mode for 5 seconds after an operation has been peiformed.
Touch the display panel to display the operation screen again.
• The display mode can be clwnged by touching [WIDE].
For operation, see "Switching Display Modes" on page 29.
1
Touch [SOURCE] on the main source screen.
The SOURCE selection screen is displayed.
2
Touch [DVD PLAYER].
The display shows the DVD mode screen.
Insert a disc with the label side facing up. The unit starts to
play the disc.
When an optional Alpine DVD player is connected:
Insert a disc into the DVDNideo CD/CD player, the player
starts playing.
To eject the disc
Press ~.
• The reverse side ofa double-sided DVD will not be played
alIIomatically.
Remove the disc. turn it over. and reinsert it.
• If the disc does not eject. press and hold
~
for at least
3
seconds.
• Do not insert discs containing maps for the navigation system. Doing
so could result in damage.
• Refer also to "DVD Setup" (pages 30 to 35).
• Be sure the remote input lead is connected to the remote output lead
of this I/nit when a DVD changer or DVD player is connected.
If
not
correctly connected. touch operation cannot be peiformed.
• To retl/rn to the previous screen during Video CD playback. touch
[RETURN] after touching
[PU2]
ofthefl/nction guide. However. the
function may vary depending on the disc.
• If the disc is left in the I/nit after
pressing~.
the disc is alllomatically
pl/lled back into the unit and stopped. In this case. start playback by
tol/ching
[.111 J
or eject again and remove the disc within 15
seconds.
• While "INDEX READING" is displayed by DivX®. the fast-
forwarding!jast-reversing and repeatfimctions. etc. cannot be I/sed.
20-EN