Adjusting The Time Correction; Setting The Time Correction Unit (Tcr Parameter) - Alpine IVA-D106 Owner's Manual

2.2ch (3WAY) System
2.2ch (3WAV) System
I
L+R
Setting contents:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAV) System I UR
Setting contents:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
4.2ch (FRONTIREARISUSW.) System
4.2ch (FRONTIREARISUBW.) System I L+R
Setting contents:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONT/REARISUBW.) System I UR
Setting contents:
LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L /
MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R
Selecting the Cut-Off Frequency
Touch
[~]
or
[~]
of FREQ., then select the cut-off
frequency (crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
2.2ch (3WAY) System
Setting contents:
LOW / MID-L 20 Hz-200 Hz
MID-H 20 Hz-20 kHz
HIGH (1 kHz-20 kHz)*}/(20 Hz-20 kHz),.}
4.2ch (FRONT/REARISUBW.) System
Setting contents:
20 Hz-200 Hz
*}
When MAKER is selected, refer to "Setting the Response Slope for
the High Range Speaker (TW Setup)" (page 47).
,.} When USER is selected, refer to "Setting the Response Slope for the
High Range Speaker (TW Setup)" (page 47).
Adjusting the Level
Touch
[<Ill]
or
[~]
of LEVEL to adjust the level.
Adjustable output level: -12 to 0 dB.
Adjusting the Slope
Touch
[~] or [~]
of SLOPE to adjust the slope.
Adjustable slope: FLAT*, - 6 dB/oct., -12 dB/oct, -18 dB/oct,
- 24 dB/oct
*
FLAT can be setfor the HIGH slope only when USER is selected in
"Setting the Response Slope for the High Range Speaker
(TW Setup)" (page 47). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope
TO
FLAT. as speaker damage may result. With this unit. a message is
displayed when the response slope for the high range speaker is set
TO
FLAT.
• Check the playback frequencies of the connected speakers before
adjusting.
• While adjusting the X-Over, you should consider the frequency
response of the connected speakers.
• Abo!lt the 2.2ch (3WAY)14.2ch (FRONTIREARISUBW) system
You can switch to 2.2ch (3WAY)14.2ch (FRONTIREARISUBW)
system mode with the 2.2ch (3WAY)14.2ch (FRONTIREARISUBW)
switch on the PXA-H 100. For details, refer to the Owner's Manual of
PXA-HlOO.
Adjusting the Time Correction
Before performing the following procedures. refer to "About Time
Correction" (page 47).
1
Touch
[»]
of T.CORR.
The TCORR adjustment screen appears.
2.2ch (3WAY) System
FRONT L(Mid-L) / FRONT R(Mid-R) / REAR L(High-L) /
REAR R(High-R) / SUBW L / SUBW R
4.2ch (FRONTIREARISUSW.) System
FRONT L / FRONT R / REAR L / REAR R / SUBW L / SUBW R
2
Touch [<Ill] or
[~]
of the desired speaker to adjust
the distance.
L
=
(distance to farthest speaker) - (distance to other
speakers)
Refer to "Time Correction Value List" on page 48.
3
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
Setting the Time Correction Unit (TCR
Parameter)
You can change the unit. (cm or inch) of time correction.
Setting Item: T.CORR PARAMETER
Setting contents: CM I INCH
CM: Time correction value is in em.
INCH: Time correction value is in inches.
45-EN