Playing A Disc; To Display The Dvd Mode Screen; If A Menu Screen Appears - Alpine IVA-W502E Owner's Manual

Playing a Disc

IVA-W502E has a built-in DVD player. When an optional Alpine DVD/
Video CD/CD player (or DVD changer) is connected to the IVA-
W502E, you can control it from the IVA-W502E (except some
operations).
WARNING
It is dangerous (and illegal in many states) for the
driver to watch the DVD/TV/Video while driving the
vehicle. The driver may be distracted from looking
ahead and an accident could occur.
Install the IVA-W502E correctly so that the driver
cannot watch DVD/TV/Video unless the vehicle is
stopped and the emergency brake is applied.
If the IVA-W502E is not installed correctly, the driver
will be able to watch the DVD/TV/Video while driving
the vehicle and may be distracted from looking ahead
causing an accident. The driver or other people could
be severely injured.

To display the DVD mode screen

• If you try to activate the auxiliary device while driving, the display
will show the warning-PICTURE OFF FOR YOUR SAFETY.
Caution
• Not all functions will operate for every DVD. See the
individual DVD's instructions for details on the
features supported.
• Fingerprints on a disc may adversely affect
playback. If a problem occurs, remove the disc and
check for fingerprints on the playback side. Clean
the disc if necessary.
• If you switch the power or Ignition key OFF or
change sources during playback, playback will
continue where you left off when you resume
playback.
• If you try to perform an invalid operation (based on
the type of disc being played), the following mark is
displayed on the monitor screen:
• Play Position Memory Function
Even if you turn power off or switch the Ignition key
to OFF during playback or change the source,
playback will continue from the point where
playback stopped when the power is turned ON
again.
18
-EN
1
Touch [SOURCE] on the main source screen.
The SOURCE selection screen is displayed.
2
Touch [DISC].
The display shows the DISC mode screen.
Insert a disc with the label side facing up. The unit starts to
play the disc.
When an optional Alpine DVD player is connected:
Insert a disc into the DVD/Video CD/CD player, the player
starts playing.
• The operation screen changes to the visual screen in the DVD or
Video CD mode for 5 seconds after an operation has been performed.
Touch the display panel to display the operation screen again.
• The display mode can be changed by touching [WIDE].
For operation, see "Switching Display Modes" on page 26.
To eject the disc
Press OPEN.
• The reverse side of a double-sided DVD will not be played
automatically.
Remove the disc, turn it over, and reinsert it.
• Do not insert discs containing maps for the navigation system. Doing
so could result in damage.
• Refer also to "DVD Setup" (pages 27 to 32).
• Be sure the remote input lead is connected to the remote output lead
of this unit when a DVD changer or DVD player is connected. If not
correctly connected, touch operation cannot be performed.
• To return to the previous screen during Video CD playback (when
PBC is set to ON), touch [
guide. However, the function may vary depending on the disc.
• "CAN'T DOWNMIX" is displayed when a Downmix (multi-channel
signals are mixed into 2ch) prohibited section of a DVD-Audio disc is
played. In this case, only the Lch/Rch recorded on the disc is output
as sound. (The sound of Centre speaker, L-surround speaker, R-
surround speaker, and Subwoofer is not output.)
• While "INDEX READING" is displayed by DivX
forwarding/fast-reversing and repeat functions, etc. cannot be used.

If a menu screen appears

On DVDs and Video CDs with playback control (PBC), menu screens
may appear automatically. If this happens, perform the operation
described below to start playback.
• To play back a DVD-Audio disc, set "VCAP" in "Setting of the DVD-
Audio Playback Mode" (page 31).
Direct Menu Operations
1 Touch the DVD menu directly.
• Some operations cannot be performed depending on the disc.
] after touching [P1/2] of the function
®
, the fast-