C O N T E N T S INTRODUCTION ......................... 4 SAFETY ............................6 III. THE JET 1 ........................... 8 IV. ASSEMBLY..........................13 COMFORT ADJUSTMENTS ....................16 VI. DISASSEMBLY ......................... 20 VII. OPERATION ..........................21 VIII. BATTERIES AND CHARGING .................... 24 IX.
Jet Power Chair. Pride is not liable for damage to property or personal injury arising out of unsafe use of a Jet Power Chair. Pride is also not liable for any property damage or personal injury arising out of the failure of any person and or/user to following the instructions and recommendations set forth in this manual or any other instructions or recommendations contained in other Jazzy related literature issued by Pride or contained on the Jet Power Chair itself.
Page 5
Pride Owners Club As an owner of a Pride product, you are invited to register your products warranty and enroll in the Pride Owners Club. You may do so by filling out and returning your enclosed registration card or by visiting Prides web site at www.pridemobility.com.
I I . S A F E T Y Your Jet 1 is a state-of-the-art, life-enhancement device designed to increase your mobility. There are certain situations, including some medical conditions, where you will need to practice operating your Jet 1 in the presence of an attendant.
MAXIMUM RECOMMENDED INCLINE Pride has performed extensive incline testing with the Jet 1. Our results show that the maximum incline your Jet 1 can safely climb is 8,7% at maximum weight capacity. The angle of most handicap access ramps is 8,7%. Any attempt to climb a steeper slope may put your Jet 1 in an unstable position.
Page 8
I I I . T H E J E T Your Jet 1 has two main assemblies: the seat and the power base. See figures 1 and 2. Typically, the seat assembly includes the armrests, seatback, seat base, and a joystick/controller. Your Jet 1 seat may also have some optional accessories attached to it, such as a basket, a cane/crutch holder, a cup holder, or a power seat switch.
Page 9
I I I . T H E J E T ARMREST ARMREST HEIGHT ADJUSTMENT KNOBS ARMREST WIDTH ADJUSTMENT SETSCREWS CONTROLLER HARNESSES Figure 2. Rear View Figure 3. Battery Charger Cord Jet 1...
Page 10
I I I . T H E J E T Specifications Suspension: Drive Wheels: 36 cm, pneumatic, center mounted (solid tyres are optional) Rear Casters: 20 cm, solid, rear articulating Anti-tip: 15 cm, solid, front mounted Max. Speed: 7 km/hr Brakes: Intelligent Braking,...
Page 11
Next, in the circuit breaker button, turn on the joystick controller and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your authorized Pride provider. n Joystick controller harness connectors: This is where the joystick connects to the motors, batteries, and charger.
Page 12
I I I . T H E J E T FREEWHEEL LEVERS For your convenience, your Jet 1 is equipped with two freewheel levers. See figures 5 and 6. These levers allow you to disengage the drive motors and maneuver the chair manually. WARNING! DO NOT use your Jet 1 while the drive motors are disengaged unless you are in the presence of an attendant! DO NOT disengage the drive motors when your Jet 1 is on an incline.
Page 13
I V . A S S E M B L Y To reduce the possibility of shipping damage, your Jet 1s seat is removed from the power base, and the seatback is removed from the seat assembly before your Jet 1 is shipped. The joystick may have also been removed from the armrest.
Page 14
I V . A S S E M B L Y SEAT INSTALLATION To install the seat: 1. Set the seat on the seat tower. See figure 8. 2. Push the seat down until the latch engages. See figure 9. 3.
Page 15
I V . A S S E M B L Y Figure 10B. Charger Inhibit Connector Figure 11. Dynamic DL Joystick Controller SLIDE JOYSTICK INTO BRACKET SETSCREW Figure 12. Joystick And Bracket Jet 1...
C O M F O R T A D J U S T M E N T S After you have become familiar with your Jet 1s operation, NUT AND BOLT you may find the need to adjust the seat. There are some adjustments you can make to increase your comfort, such as seat height and angle, armrest height and angle, footrest height and angle, and joystick position.
C O M F O R T A D J U S T M E N T S ARMREST ANGLE ADJUSTMENT You can adjust the armrest angle to fit your specific needs. See figure 15. TURN THIS SCREW TO To change the armrest angle: CHANGE 1.
Page 18
C O M F O R T A D J U S T M E N T S FOOTREST HEIGHT The footrest height is easily adjusted to one of six different heights in 2,5 cm increments. To raise or lower the footrest: 1.
Page 19
C O M F O R T A D J U S T M E N T S 3. Slide the leg rest in or out to the desired length. 4. Tighten the bolt and reinstall the two screws on each leg rest extension.
V I . D I S A S S E M B L Y SEAT REMOVAL You may wish to remove the seat for transportation. See figure 23. To remove the seat: 1. Turn the power off. 2. Make sure your Jet 1 is not in freewheel mode. 3.
V I I . O P E R A T I O N You control the speed and direction of your Jet 1 with the joystick controller. WARNING! Do not use the on/off key to stop the chair. This may cause injury. To operate your Jet 1: 1.
Page 22
V I I . O P E R A T I O N JOYSTICK FUNCTIONS The joystick function is similar for all controller configurations. The joystick controls the direction and speed of the power chair. See figure 25. When you move the joystick from the neutral (center) position, the electromagnetic brakes release and allow the power chair to move.
Page 23
means all 6 LEDs flash on for a period of 0,2 seconds and off for 0,8 seconds. means all 6 LEDs are off for a period of two seconds before flashing sequence repeats. If you cannot resolve your problem, see your authorized Pride provider. Jet 1...
V I I I . B A T T E R I E S A N D C H A R G I N G BATTERIES Your Jet 1 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance-free. Since they are sealed, there is no need to check the electrolyte (fluid) level.
Page 25
V I I I . B A T T E R I E S A N D C H A R G I N G 4. Extend the charger power cord and plug it into the wall outlet. The Jet 1 incorporates an inhibit function that disables the power chair when the charger is plugged into a wall outlet.
Page 26
You should use the charger supplied with the Jet 1. It is the safest, most efficient tool to charge the batteries. We do not recommend using other types of chargers (e.g., an automotive battery charger). Your Jet 1s charger will not operate after the batteries have been discharged to nearly zero voltage. If this happens, call your authorized Pride provider for assistance.
Page 27
We work closely with our battery manufacturer to provide a battery that best suits your Jet 1s specific demands. Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encounter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the power available and extends the time needed to recharge the battery (just as with a car battery).
Page 28
V I I I . B A T T E R I E S A N D C H A R G I N G How should I store my Jet 1 and its batteries? If you do not use your Jet 1 regularly, we recommend maintaining battery vitality by charging the batteries at least once per week.
Your Jet 1 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your authorized Pride provider. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your Jet 1 gives you years of trouble-free operation.
Check the rubber boot around the base of the joystick for damage. Visually inspect the boot. Do not handle or try to repair it. See your authorized Pride provider if there is a problem. n Visually inspect the controller harnesses. Make sure that they are not frayed or cut or have any wires exposed.
See V. Comfort Adjustments. n Check for extreme wear on the anti-tip wheels. Replace them as necessary. n Check for drive tyre wear. See your authorized Pride provider for repair. n Check the rear caster wheels for wear. Replace them as necessary.
Page 32
If you should have a flat tyre, you should replace the tube. Replacement tyres and tubes are readily available at the Pride provider shop where you purchased your Jet 1.
1. Remove the seat and body shroud. See VI. Disassembly. 2. Unscrew the motor brush caps. See figure 31. 3. Remove the brushes. 4. Inspect for wear. 5. Replace brushes, if necessary. Contact your authorized Pride pro- vider for replacement brushes. Figure 31. Motor Jet 1...
Page 34
WHEN TO SEE YOUR PRIDE PROVIDER FOR SERVICE The following symptoms could indicate a serious problem with your Jet 1. If necessary, contact your authorized Pride provider. When calling, have the model number, serial number, nature of the problem, and the trouble code, if available.
A N D A C C E S S O R I E S The following accessories are available from your authorized Pride provider. OXYGEN TANK HOLDER The removable oxygen tank holder is mounted to the back of the seat by means of the accessory bracket. See figure 32.
Page 36
O P T I O N S A N D A C C E S S O R I E S Figure 32. Oxygen Tank Holder Figure 33. Cane And Crutch Holder Figure 34. Walker Holder Figure 35. Rear Basket Jet 1...
ONE-YEAR LIMITED WARRANTY Your Pride Jet 1 is fully guaranteed for twelve (12) months from the date of purchase against faults arising due to defects in manufacture or materials. This warranty does not detract from, but is in addition to your legal rights.