Set Chime Zones; Set Part 2 Zones - Bosch Solution 144 User Manual

Solution 144 User Guide
2. Use the [] and [] keys to select the zone that you
want to bypass, then press [OK]. Alternatively, you
can enter the zone number that you want to bypass,
then press [OK].
If the zone is bypassed, the keypad will prompt:
Zone 1 Name Zn1 is
bypassed. To un-bypass,
press OFF.
Press OK or MENU
If the zone is not bypassed, the keypad will prompt:
Zone 1 Name Zn1 is
un-bypassed. To bypass,
press ON.
Press OK or MENU
3. Press [ON] or [OFF] to toggle the zone to be
bypassed/un-bypassed.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Repeat steps 1 to 4 to bypass or un-bypass
additional zones.
Inputs > Commands >

Set Chime Zones

This menu allows you to program zones to be monitored
when the system is turned off. Chime mode is ideal to
monitor a front door to sound the keypad buzzer when
opened (faulted).
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [3].
A list of areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program zones for chime mode, then press
[OK]. Alternatively, you can enter the area number
that you want to program chime zones, then press
[OK].
The keypad will list all zones that can be
programmed for chime mode. A '' displayed on
the right side of the zone name indicates that the
zone is already set for chime.
Zn1 Zone 1 Name 
Zn2 Zone 2 Name
Zn3 Zone 3 Name
Press

3. Use the [] and [] keys to select the zone that you
want to set for chime, then press [OK]. Alternatively,
you can enter the zone number that you want to set
for chime, then press [OK].
If the zone is not programmed for chime, the keypad
will prompt:
22
MENU 3-0-3
OK or MENU
Zone 1 Name Zn1
Zone Chime is OFF,
To turn ON, Press ON.
To Go Back Press OK
If the zone is programmed for chime, the keypad
will prompt:
Zone 1 Name Zn1
Zone Chime is ON.
To turn OFF, Press OFF.
To Go Back Press OK
4. Press [ON] or [OFF] to toggle the zone to be
monitored when chime mode is turned on.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Inputs > Commands >

Set Part 2 Zones

This menu allows you to program which zones are to be
monitored when an area has been turned Part 2 On.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [3] + [0] + [4].
A list of areas will display on
2. Use the [] and [] keys to select the area that you
want to program zones for Part 2 On, then press
[OK]. Alternatively, you can enter the area number
that you want to program Part 2 On zones, then
press [OK].
The keypad will list all zones that can be
programmed for Part 2 On. A '' displayed on the
right side of the zone name indicates that the zone
is already bypassed.
Zn1 Zone 1 Name 
Zn2 Zone 2 Name
Zn3 Zone 3 Name
Press

3. Use the [] and [] keys to select the zone that you
want to set for Part 2, then press [OK]. Alternatively,
you can enter the zone number that you want to set
for Part 2, then press [OK].
If the zone is not programmed for Part 2, the keypad
will prompt:
Zone 1 Name Zn1
Is not armed in Part2,
To Enable, Press ON.
To Go Back Press OK
If the zone is programmed for Part 2, the keypad will
prompt:
Bosch Security Systems 04/12 BLCC600U
MENU 3-0-4
the keypad.
OK or MENU