Connection - Panasonic DMR-EX75 Operating Instructions Manual

FUNCTIONS
FUNCTIONS
To Others
Setup
TV Aspect
Progressive
TV System
Tuning
HDMI Settings
Disc
Picture
AV1 Output ( Scart )
Sound
AV2 Settings
Display
Active Antenna

Connection

TAB
SELECT
Others
ENTER
AV-Link function
Switching between television reception and
the signal from the DVD Recorder. This
function is only possible if the AV1 Output
is set to [Video ( with component )] or
[RGB 2 ( without component )].
DVD recorder signal: Press ENTER + 0.
DVD appears on the display.
Television reception: Press the buttons again.
TV appears on the display.
Setup
AV2 Settings
AV2 Input
Tuning
Ext Link
Disc
Picture
Sound
Display
AV2 Input
Connection
Others RGB / Video
RGB
Video
S Video
SELECT
ENTER
RETURN
Not NTSC:
RGB / Video, S VIDEO, Ext Link 1, Ext Link 2.
Setup
SETUP
Connection
16:9
Off
TV Aspect
PAL
Select the TV screen format of your television. Programmes in 16:9 format are recorded
Video
in 4:3 format. 16:9 format is used to record to HDD/RAM.
Letterbox: Black bars appear on the upper and lower edges of the screen (16:9).
Off
Progressive
RETURN
On: The signal is displayed in full-picture quality using COMPONENT VIDEO OUT.
Cannot be changed over when HDMI [Digital Audio Output] is set to [Automatic] and
the HDMI terminal is being used.
TV System
PAL: You connect the unit to a PAL or multi-system television. Programmes that were
recorded with NTSC are played as PAL60.
NTSC: You connect the unit to an NTSC television. Programmes that were recorded
with NTSC are played as NTSC.
HDMI Settings
HDMI (High Definition Multimedia Interface) is a digital interface for Audio and Video.
One single cable transfers both digital video data (picture data) and also digital audio
data. There is no longer any need to convert analogue-digital or digital-analogue.
HDMI works without data compression so that there is therefore no quality loss from
the system.
AV1 Output ( Scart )
Video ( with Component ): Factory-default settings.
S Video ( with Component ): Select when a TV is connected that can receive an
S Video signal.
RGB 1 ( without Component ): Select this setting when a TV set is connected up
which can receive an RGB signal. Select this mode if you always want to see the
picture in RGB signals.
RGB 2 ( without Component ): Select this setting when a TV set is connected up
which can receive an RGB signal. Select this mode if you always want to see menus
in RGB signals.
AV2 Settings
RGB / Video
Ext Link 2
AV2 Input
RGB / Video: When receiving or recording RGB output from external equipment.
RGB, Video, S Video: The input is switched to the selected signal.
Ext Link
Ext Link 1:
Ext Link 2:
Active Antenna
On: When you connect an aerial which shares the power circuit of the DVD Recorder.
Start the Auto-Setup again after making the adjustment and check the
signal properties.
Setting
AV2 Input
Ext Link
For digital receivers that send a special recording control signal,
for example, the F.U.N. receiver (TU-DSF41).
External recording control for satellite or digital receivers (video signal).
Option
ENTER
[16:9] [4:3] [Letterbox]
[On] [Off]
[PAL] [NTSC]
[Video ( with Component )]
[S Video ( with Component )]
[RGB 1 ( without Component )]
[RGB 2 ( without Component )]
Perform the settings in the
following submenus for the
connected unit.
[RGB / Video] [RGB] [Video] [S Video]
[Ext Link1] [Ext Link 2]
[On] [Off]
ENTER
99 19
66 99
60 99
65