Table of Contents
Advertisement
1
STEP
You need a Conditional Access Module together with a valid Smart Card and a subscription with the corresponding CATV provider if you want to
watch/record encrypted digital CATV broadcasts.
1 Insert the certified Smart Card into the commercially available CAM (Conditional Access Module).
2 Insert the CAM into the CI (Common Interface) slot of this unit.
TV service encryption is automatically cancelled and the service can be viewed or recorded.
≥When using unencrypted digital terrestrial broadcasts or analogue broadcasts, you do not need to insert CAM. Proceed to STEP 2. (
The recording might be prohibited by broadcasters.
§
This unit's rear panel
RF
IN
VIDEO
L
R
RF
OUT
AUDIO
OUT
OUT
CI (Common Interface)
CAM (Conditional Access Module)
2
STEP
Using a 21-pin Scart cable
≥You can use a variety of Q Link functions by connecting the unit to a Q Link compatible television (
≥You can enjoy high-quality viewing by connecting the unit to an RGB compatible television (
Required setting
"AV1 Output" in the Setup menu (
≥Before connection, turn off all equipment and read the appropriate operating instructions.
≥Refer to "Additional connections" (
When the unit is not to be used for a long time
To save power, unplug it from the household mains socket. This unit consumes a small amount of power, even when it is turned off.
[approx. 0.3 W ("Power Save in Standby" is activated and "RF OUT ( Aerial Signal )" is set to "Off".)]
Connecting a television
To the terrestrial aerial
Cable
1
Aerial cable/
CATV coaxial
cable
For viewing digital satellite broadcasts,
connect this unit with a digital satellite
receiver before connecting the AC
mains lead.
Required setting
"AV2 Input" setting in the Setup menu
(
70)
VQT4W64
6
Insert the CAM (Conditional Access Module) and Smart Card
COMMON INTERFACE
COMMON INTERFACE
COMMON INTERFACE
AV1
(TV)
OPTICAL
DIGITAL AUDIO OUT
DIGITAL AUDIO OUT
AV2
(PC
PCM/
M/BITSTREAM
BITSTREAM)
(EXT)
AC IN
AC IN
slot
2
Smart Card
Connection
69)
73, 74) for connection using other terminals and connection with other equipment.
Television's rear panel
VHF/UHF
RF IN
RF coaxial cable
(supplied)
2
2
Fully wired 21-pin
Scart cable
RF
IN
VIDEO
L
R
RF
OUT
AUDIO
OUT
OUT
Digital satellite
receiver's rear panel
Note
≥Be sure to insert the CAM horizontally into the slot.
≥Insert the CAM with the correct direction.
≥For more details, see the manual of the CAM and Smart
AC IN
Card, or consult the dealer.
≥The Common Interface supports the modules according to
DVB Specification and CI Plus Specification.
≥Unplug the AC mains lead before you insert or remove the
CAM with Smart Card. Remove it slowly.
1
AV
Connect only after all other connections are
Connecting a terminal other than the
21-pin Scart terminal (
3
Common Interface (CI) slot
In order to view or record encrypted CATV services,
you must insert a certified CAM and Smart Card
into this slot. (
COMMON INTERFACE
COMMON INTERFACE
COMMON INTERFACE
AV1
(TV)
AV2
(EXT)
Connect the unit directly to the
television
21-pin Scart
If you connect the unit through an AV
cable
selector or video cassette recorder to
the television, video signal will be
affected by copyright protection systems
and the picture may not be shown
correctly.
AV
≥When connecting to a television
with a built-in VCR
Connect to the input terminals on the television side if
there are both television and VCR input terminals.
§
39).
86).
To household mains socket
(AC 220 to 240 V, 50 Hz)
AC mains lead
(supplied)
complete.
7, 74)
above)
OPTICAL
Cooling fan
This unit's rear panel
below)
4
AC IN
DO NOT
Television
VCR
This unit
Advertisement
Table of Contents
