Honeywell MX7 Tecton Reference Manual page 93

Message
Switching to admin- The keyboard hook load failed, so AppLock switches to admin mode. If a password is specified, the password
kbdhook.dll not found prompt is displayed and remains until a valid password is entered.
Switching to admin-key-
If the keyboard hook initialization fails, AppLock switches to admin mode. If a password is specified, the pass-
board hook initialization fail-
word prompt is displayed and remains until a valid password is entered.
ure
Switching to admin-reg- See the explanation of the "Registry read failure" above. AppLock is switching into Admin mode. If a password
istry read failure has been configured, the prompt will be displayed and will not be dismissed until a valid password is entered.
Switching to Task-
In administration mode, the taskbar is visible and enabled.
barScreenMode
Switching to user mode The registry was successfully read and AppLock is starting the process to switch to user mode.
Switching to user-hotkey The system is currently in admin mode and is now switching to user mode. The switch occurred because of a
press hotkey press by the administrator.
Taskbar hook failure AppLock is unable to control the taskbar to prevent the locked application from re-enabling it.
Taskbar hook OK AppLock successfully installed control of the taskbar.
Timeout looking for app After the application is launched, AppLock must wait until the application has initialized itself before proceeding.
window The application did not start successfully and AppLock has timed out.
ToUser after admin, not at The user mode switch is attempted when the device boots and after the administrator presses the hotkey. The
boot mode switch is being attempted after a hotkey press.
ToUser after admin-app The switch to user mode is being made via a hotkey press and the administrator has left the application open
still open and has not made any changes in the configuration.
If user mode is being entered via a hotkey press, the administrator may have left the configured application
ToUser after admin-no
open. If so, AppLock does not launch the application again unless a new application or command line has been
app or cmd line change
specified; otherwise, it just locks it.
The desktop is moved when switching into user mode. This prevents them from being visible if the application is
Unable to move desktop
exited and restarted by the timer. This error does not affect the screen mode switch; processing continues.
The taskbar is moved when switching into user mode. This prevents them from being visible if the application is
Unable to move taskbar
exited and restarted by the timer. This error does not affect the screen mode switch; processing continues.
Unhook taskbar wndproc
AppLock could not remove its control of the taskbar. This error does not affect AppLock processing
failure
Unhook wndproc failure AppLock could not remove the hook that allows monitoring of the application.
In administration mode, the taskbar should return to normal operation, so AppLock's control of the taskbar
Unhooking taskbar
should be removed.
When the administrator leaves user mode, the device is fully operational; therefore, AppLock must stop mon-
Unhooking wndproc
itoring the locked application.
WM_SIZE adjusted This message denotes that AppLock has readjusted the window size.
X after Ctrl+L Processing the backdoor entry.
Ret from password <#> Return value from password dialog.
Decrypt data len <#> Length of decrypted password.
Window handle to enum- The window handle that is passed to the enumeration function. This message can be used by engineering with
windows=%x other development tools to trouble shoot application lock failures.
WM_WINDOWPOSCHG
Output the window size after it has been adjusted by AppLock
adjusted=%x
Explanation and/or corrective action Level
LOG_PROC-
ESSING
LOG_PROC-
ESSING
LOG_PROC-
ESSING
LOG_EX
LOG_PROC-
ESSING
LOG_PROC-
ESSING
LOG_ERROR
LOG_EX
LOG_ERROR
LOG_EX
LOG_EX
LOG_EX
LOG_ERROR
LOG_ERROR
LOG_ERROR
LOG_ERROR
LOG_EX
LOG_EX
LOG_EX
LOG_EX
LOG_EX
LOG_EX
LOG_EX
LOG_EX
4-55