Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Samsung DCS-VIP
Summary of Contents for Samsung DCS-VIP
- Page 1 SAMSUNG DCS-VIP INTERNET KEYPHONE QUICK GUIDE INSTALLATION & CONFIGURATION...
- Page 2 Samsung Telecoms reserves the right without prior notice to revise information in this publication for any reason. Samsung Telecoms also reserves the right without prior notice to make changes in design or components of equipment as engineering and manufacturing may warrant.
- Page 3 2001-03-31 ..........................(place and date of issue) (name and signature of authorized person) (Representative in the EU) Samsung Electronics Euro QA Lab. Blackbushe Business Park Saxony Way, Yateley, Hampshire GU46 6GG, UK In-Seop Lee / Manager IS Lee 2001-04-03 ..........
-
Page 4: Intended Use
Intended Use This apparatus provides a number of Samsung proprietary digital extensions, analogue exten- sions, 10/100 Base-T LAN connections, an integral Router and an integral CTI Telephony Server. It is intended to connect only to ISDN Basic Rate circuits provided by a public net- work operator. -
Page 5: Table Of Contents
5 Restoring System Configuration Information ............. 22 Restoring Router Configuration Information from Flash Memory ..........22 Restoring Configuration Information from PC Hard Disk ............23 6 DCS-VIP Remote Programming ................25 Assumptions.......................... 25 Remote Programming Procedure on Slave Site ..............25 Remote Programming Procedure on Master Site .............. -
Page 6: Introduction
Call your ISDN service provider and apply for an ISDN BRI line (ISDN 2). You should have a network card installed in the PC to be connected to the DCS-VIP Ethernet port. Check that the TCP/IP protocol is also installed. -
Page 7: Product Specifications
DCS-VIP Internet Keyphone Quick Guide Product Specifications Product Specifications Hardware Specifications Router Module Motorola MC68EN360 Keyphone Module Motorola MC68EN302 16Mb DRAM Router Module 2Mb Flash Memory 8Mb DRAM Keyphone Module 2Mb Flash 2 ISDN BRI Interfaces : S/T type 1 VoIP port : RJ-45... -
Page 8: Environmental Requirements
Power Consumption : 70 Watts Operating Temperature : 0°C – 40°C Relative Humidity : 10% – 90% (Non-condensing) Caution When installing the DCS-VIP main router you must ensure a free space of at least 100mm above the unit. — 3 —... -
Page 9: Installing Your Dcs-Vip
¶ Grounding the VIP Router The DCS-VIP base unit is provided with a third-wire AC ground through the power cord, which is adequate for most applications. However, if it is suspected that there is a problem with the ground provided at the AC outlet, or local codes require a solid earth ground to be connected to the router, the existing third -wire ground must be disconnected and a new ground connected to the grounding lug on the rear of the unit (see illustration below). -
Page 10: Connecting The Isdn Line(S)
Connecting a PC Connecting a PC There are eight Ethernet ports on the rear panel of the DCS-VIP. You can connect a PC to each Ethernet port (a maximum of eight PCs). 1. Connect an Ethernet cable to any of the Ethernet ports on the rear panel of the DCS-VIP. -
Page 11: Connecting Digital Or Analogue Telephones
¹ Connecting Digital or Analogue Telephones You can connect a digital telephone to a DLI port on the rear panel of your DCS-VIP, and you can connect an analogue telephone to an SLI port. 1. Connect the telephone cable to the port labelled DLI or SLI on the rear panel of your DCS- VIP. -
Page 12: Connecting An Expansion Unit
An optional expansion unit can be connected with the main unit if there are more PCs or tele- phones to connect to the DCS-VIP than the main unit can handle. The expansion unit provides a further two ISDN circuits and a further 10 voice ports. -
Page 13: Configuring Your Dcs-Vip
Configuring Your DCS- - VIP Configuring Your DCS After installing the DCS-VIP system, switch it on. Using a PC, run a web browser and connect to the default system IP address. Run the Wizard Setup on the startup screen of the DCS-VIP to easily and quickly configure the system. -
Page 14: Running The Wizard Setup
4. Enter the default User Name ‘guest’ and Password ‘samsung’. The web-based management screen for the DCS-VIP appears. ¹ Running the Wizard Setup By running the Wizard Setup, you can easily and quickly configure the DCS-VIP system. — 9 —... -
Page 15: Configuring The Keyphone Functions
Setup Wizard On this screen, you can set the area code, system date and system status. Set the following parameters. Area Code: Enter the code of the area where the DCS-VIP will be installed. (Not used in UK.) — 10 —... - Page 16 System Date: Set the system date and time. The set date and time will be save d in the system memory. System Status: Displays system status, such as whether the DCS-VIP system is equipped with the VoIP function, if an expansion unit is connected, and the trunk line type.
- Page 17 DCS-VIP Internet Keyphone Quick Guide In the Day field, set the station telephone number to ring for incoming calls on each trunk. For example, to set station 208 to ring for calls on trunk 704, click the dropdown button to the right of Trunk No.
-
Page 18: Configuring The Router Functions
ROUTER SETUP option. In the Router Wizard Setup, you can configure the LAN and WAN environment necessary for connecting to either the Internet (ISP) or a remote node using the DCS-VIP. Router Wizard Setup - - Setup 1 Router Wizard Setup... - Page 19 DHCP Server: Choose whether to use the DCS-VIP as a DHCP server. Enable: Select to allocate the IP addresses in the PCs connected to the DCS-VIP. − Disable: Select not to use the DHCP function. If you select "Disable", the network −...
- Page 20 If you chose Remote Router for the Connect To parameter on the Router Wizard Setup - Setup 1 screen, the following parameters will be displayed. Note The following is included for your information. For a more detailed example of remote programming, refer to section 6, DCS-VIP Remote Programming. — 15 —...
-
Page 21: Configuring The Voip Functions
For ISP connection, the NAT function will be automatically enabled. For Remote Router connection, the NAT function will be automatically disabled. Now that initial setup for the DCS-VIP router is complete, you will be able to connect to the Internet or to the remote router through the ISP. - Page 22 DCS-VIP Internet Keyphone Quick Guide Note The following is included for your information. For a more detailed example of installing and configuring the VoIP feature, see the Appendix. VoIP IP Address VoIP IP Address On the VoIP IP Address screen you can set up the VoIP IP address and subnet mask.
- Page 23 DTMF Generation Type(#) – Options are Inband/Signalling/DCS-VIP. Gatekeeper Type(#) – Options are Samsung Gatekeeper/Other Gatekeeper. Billing Type(#) – Options are Samsung Billing Type/Standard Billing Type. Note: Options marked (#) cannot be changed while the VoIP card is in use. Click the Next button.
-
Page 24: Changing The System Ip Address
Use the ADVANCE SETUP menu on the DCS-VIP web management screen to change the sys- tem IP address. When you connect to the ISP, you can use the default IP address for the DCS-VIP or change it to match the network neighbourhood. -
Page 25: Saving System Configuration Information
If you changed the DCS-VIP system IP address, you must change the TCP/IP properties of the PC connected to the DCS-VIP system to those which best match the DCS-VIP system IP address. Make sure that the DNS numbers of the ISP are configured in the PC. - Page 26 DCS-VIP Internet Keyphone Quick Guide From the keyphone, open system programming and select MMC 818. Select YES to COPY K/P DB and confirm your selection. iii) If you have configured an optional VoIP card, select COPY VOIP DB, then select YES and con- firm your selection.
-
Page 27: Restoring System Configuration Information
DCS-VIP Internet Keyphone Quick Guide Restoring System Configuration Restoring System Configuration Informa a tion Inform tion Configuration information you save can be used to restore your system to its original configura- tion if there is a problem. Router configuration can be restored either from the flash memory us- ing the MIB SAVE/RESTORE option, or from the PC’s hard disk using the RESTORE CONFIG op-... -
Page 28: Restoring Configuration Information From Pc Hard Disk
DCS-VIP Internet Keyphone Quick Guide Select the Router option and click the Set button to reboot. · Restoring Configuration Information from PC Hard Disk You can restore configuration information for the router, VoIP card and keyphone from the files you have saved on the hard disk. - Page 29 DCS-VIP Internet Keyphone Quick Guide MPORTANT If you are restoring the Router or VoIP configuration, you must do a system reboot (‘warm’ § boot) after restoring the file. Click the SYSTEM REBOOT option in the SYSTEM MANAGE- MENT menu. You see the System Restart screen.
-
Page 30: Dcs-Vip Remote Programming
DCS-VIP Internet Keyphone Quick Guide DCS– – VIP Remote Programming VIP Remote Programming This part of the guide explains how to set up and use the Remote Programming facility of the DCS-VIP system. Assumptions Assumptions The following assumptions are made: You are familiar with the DCS–VIP system and the use of the Web Management screens as... - Page 31 DCS-VIP Internet Keyphone Quick Guide If Using MSN—Assign MSN Number Using the Web screen interface—or MMC 421 (MSN Digit) on a digital keyset—configure an MSN number to direct an incoming call to one of the internal LAN ports (891 and 892). The MSN number chosen should not be used by any other port on the system.
-
Page 32: Remote Programming Procedure On Master Site
DCS-VIP Internet Keyphone Quick Guide · Remote Programming Procedure on Master Site Remote Router Connection Wizard On the Master router, run the Router Configuration Wizard and select the Remote Router Con- nection option (Fig. 4). Enter the IP Address of the Master router (in this example it is set as 192.168.0.1) and select a fixed 64K ISDN connection. - Page 33 DCS-VIP Internet Keyphone Quick Guide The Phone Number is the number that has already been configured in the Slave router (529472 in the examples shown in Figs. 1 and 2) and should include the area code. The Router Login Name and Password are the same as those configured on the PPP Incoming Security Setup page for the Slave router (Fig.
- Page 34 DCS-VIP Internet Keyphone Quick Guide To configure a static IP route, enter the Destination IP Address and Subnet Mask of the Slave router (these are 207.256.24.15 and 255.255.255.0 in the example shown in Fig. 8). Enter the Gateway IP address of your Network. This will usually be the IP address of the Master router (192.168.0.1 in this example).
-
Page 35: Appendix: Installing & Programming Voice Over Ip (Voip) On The Dcs-Vip
DCS-VIP Internet Keyphone Quick Guide Appendix: Installing and Programming Appendix: Installing and Programming Voice Over IP (VoIP) on the DCS- - VIP Voice Over IP (VoIP) on the DCS The following describes how to install and program the optional Voice over IP (VoIP) feature us- ing a real-life example. - Page 36 DCS-VIP Internet Keyphone Quick Guide Installing VoIP Option Card Installing VoIP Option Card Refer to the installation instructions supplied with your card for full details on installing the card. The basic steps are as follows. 1. Switch off the unit and disconnect the power cord.
- Page 37 (CLI) to the called party. DTMF Generation Type(#) – Inband/Signalling/DCS-VIP. • Gatekeeper Type(#) – Samsung Gatekeeper/Other Gatekeeper. • Billing Type(#) – Samsung Billing Type/Standard Billing Type. • Note: Options marked (#) cannot be changed while the VoIP card is in use. — 32 —...
- Page 38 DCS-VIP Internet Keyphone Quick Guide The next screen is the IP conversion table. This table is used to convert dialled digits into IP a d- dresses. For example, if you wish to dial from this VIP (site 3) to the Korean system (site 5), you would dial 500;...
- Page 39 DCS-VIP Internet Keyphone Quick Guide (Click the scrollbar to see other options.) There are only three options that should be changed in this table. Input Gain( ) – The optimum value is –3Db. (After changing this option, you must restart •...
- Page 40 The DDI table allows incoming calls to access all extensions, all station groups and trunk group Allow Break In and Break Out This is done using MMC programming from a keyphone. (Refer to the Samsung DCS-VIP Inter- net Keyphone Programming Manual for details.)
- Page 41 DCS-VIP Internet Keyphone Quick Guide Incoming DDI number 623 will access the VoIP channels Incoming MSN number 8 will access the VoIP channels It does not matter which channel is set as the destination as the call will go to any free channel.
- Page 42 Samsung Telecoms (U.K.) Limited Brookside Business Park, Greengate, Middleton, Manchester M24 1GS Tel: 0161 655 1100 Fax: 0161 655 1166...