Access Codes; Arming/Disarming - DSC Power 832 Installation Manual

All keypads provide complete information and control of the alarm panel. The panel can be completely programmed via any
keypad on the system. ICON/LED keypads provide function indicator lights and individual zone indicator lights for the alarm
circuits. The LCD keypad provides function indicator lights and word descriptions for zone status.
The following sections describe how to arm, disarm and perform other keypad functions.
3.1

Access Codes

All 38 access codes have the ability to arm/disarm any partition(s) for which they are enabled and to activate the PGM
outputs using the [✱][7] commands (See Section 3.4 "[ ✱ ] Commands, [ ✱ ][7]") .
Additional access code attributes are also programmable. Attributes determine what abilities the code will have.
To program each attribute;
1. Enter [✱] [5] [master code] [9] to enter the attribute programming mode.
2. Enter the 2-digit number of the access code you want to edit.
3. Enter the attribute number to toggle it on or off.
The programmable attributes are as follows:
• Attribute 1: Partition 1 operation enabled Attribute 1: Partition 1 operation enabled Attribute 1: Partition 1 operation enabled Attribute 1: Partition 1 operation enabled
Attribute 1: Partition 1 operation enabled
• Attribute 2: Partition 2 operation enabled Attribute 2: Partition 2 operation enabled Attribute 2: Partition 2 operation enabled Attribute 2: Partition 2 operation enabled
Attribute 2: Partition 2 operation enabled
• Attribute 3: Zone bypass enabled Attribute 3: Zone bypass enabled - This attribute allows the user to bypass zones. Attribute 3: Zone bypass enabled Attribute 3: Zone bypass enabled Attribute 3: Zone bypass enabled
• Attribute 4: Escort5580 remote access Attribute 4: Escort5580 remote access Attribute 4: Escort5580 remote access - This attribute allows the user to access the security system via the Attribute 4: Escort5580 remote access Attribute 4: Escort5580 remote access
Escort, if installed.
Attribute 5: Downlook Attribute 5: Downlook r r r r r emote Attribute 5: Downlook
• Attribute 5: Downlook Attribute 5: Downlook
(see the PC5108L Installation Manual for details).
• Attribute 6: Downlook Attribute 6: Downlook Attribute 6: Downlook r r r r r emote Attribute 6: Downlook Attribute 6: Downlook
4L (see the PC5108L Installation Manual for details).
Master code attributes cannot change. By default, each code has the attributes of the code used to
program it.
The available access codes are as follows:
General Access Codes - Access Codes [01] to [32]
Each access code can be used to arm and disarm the system. All access codes can access the [*][6] menu.
Enable any of the access code attributes to allow access to the above-mentioned functions (access code
attributes 1-6).
Duress Codes - Access Codes [33] and [34]
When a duress code is used to perform any function the panel will report a duress reporting code ( see Section 5.7
"Communicator - Reporting Codes" ).
Partition Master Codes - Access Codes [41] and [42]
Partition master codes can program additional access codes and the duress code for their partition.
System Master Code - Access Code [40]
By default the system master code is enabled to operate on both partitions and can perform any keypad function. This
code can be used to program all access codes as well as the partition master codes and duress codes.
If the Master Code Not Changeable option is enabled the system master code can only be changed using Installer
Programming.
For instructions on programming access codes, see the PC5015 Instruction Manual ("Programming Access Codes").
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Code Required for Bypass ..................................... Section [015], Option [5]
Master Code Not Changeable option .................... Section [015], Option [6]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Maintenance Code
The maintenance code can only be used to arm and disarm the system. It cannot be used to bypass zones or to
access the Escort5580. The code can only be programmed in Installer Programming.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Maintenance Code ................................................. [008]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3.2 Arming / Disarming
When arming, once the Exit Delay has expired, the system will allow 7 seconds for detectors to settle before the
system is armed. If any zone is violated when the 7 second settle time expires, the system will cancel arming.
When arming is cancelled, the keypad buzzer will sound a steady tone for 90 seconds. During Exit Delay, any
zone violated will sound a series of beeps to notify the user that a zone on the system has not been restored.
To disarm the panel enter the premises through the designated entry/exit door. The keypad will emit a steady beep to warn
that you must disarm the system. During the last 10 seconds of entry delay the panel will pulse the keypad beeper on and
off rapidly to warn the entry delay is about to expire. Enter a valid access code at the keypad. If an error is made, re-enter
the code correctly. When a correct code is entered the keypad will turn off the Armed light and stop the keypad buzzer. If
an alarm occurred while the panel was armed the Memory light and the zones which caused the alarm will be flashing. Press
the [#] key to return the keypad to the Ready state.
Keypad Commands
S E C T
emote t t t t t rigger to emote emote rigger to t t t t t elephone rigger to rigger to elephone elephone elephone n n n n n umber 1 umber 1 umber 1
emote rigger to elephone umber 1 umber 1 - For use with the Escort5580 and the PC5108L/DLM-4L
emote emote t t t t t rigger to emote emote rigger to rigger to rigger to t t t t t elephone rigger to elephone elephone elephone n n n n n umber 2 elephone
13
I O N 3
umber 2 - For use with the Escort5580 and the PC5108L/DLM- umber 2 umber 2 umber 2