Global And Partition Keypad Operation; Features Available For The Lcd5500Z - DSC Power 832 Installation Manual

K E Y P
[17] - [✱]+[1] Reactivate Stay/Away Zones
This function key provides the user with a simple method for adding Stay/Away zones back into the system (see
Section 3.4 "[ ✱ ] Commands, [ ✱ ] [1] Reactivate Stay/Away zones" ).
[18] Identified Voice Prompt Help
This feature can only be programmed if both the Escort5580 and the PC5928/PC5936 audio matrix module are being
used. When the function key is pressed, the Escort will begin a help session from the intercom station programmed
as closest to the keypad. In order for this option to function, you must program PC59xx Section [802], subsection
[14] "Keypad Port Assignments." For more information, please refer to the PC5928 or PC5936 Installation Manual .
Note: This function key cannot be programmed for PC55XXZ ICON/LED keypads with software version 1.0.
[19] - [✱]+[2]+[3] Command Output 3
[21] - [✱]+[2]+[4] Command Output 4
Function keys [19] and [21] provide the user with a simple method of activating an output programmed as
Command Output Option 3 or 4.
[22] - Active Camera Monitor Selection
This function key is for use with the PC5108L Downlook interface/camera monitor module. For instructions on the
function key use, see the PC5108L Installation Manual.
[23] - Bypass Recall
Pressing this function key will recall the last group of bypassed zones. The function key will follow the Code Required for
Bypass option. If the option is enabled, a valid access code with the Bypass attribute enabled must be entered after the Bypass Bypass
Bypass Bypass
function key is pressed. For instructions on zone bypassing, see the PC5015 Instruction Manual .
[24] - Recall Bypass Group #1
This function key will recall zones in Bypass Group #1. This group is programmed by the user in the [*][1]
Bypass menu. The function key will follow the Code Required for Bypass
access code with the Bypass attribute enabled must be entered after the function key is pressed. For
instructions on zone bypassing and programming Bypass Groups, see the PC5015 Instruction Manual .
[25] - Recall Bypass Group #2
This function key operates similarly to function key [24] but will recall zones in Bypass Group #2. For instructions on
zone bypassing and programming Bypass Groups, see the PC5015 Instruction Manual.
3.6

Global and Partition Keypad Operation

A global keypad will not display any information (the trouble LED will light if a trouble condition is present) until a partition
is selected. To select a partition the user must press and hold the [1] key for partition 1 or the [2] key for partition 2 for two
seconds. The keypad will then display the status of the selected partition and allow normal operation.
A partition keypad will display the status of the partition for which it has been programmed. A user with access to
both partitions may temporarily assign the keypad to the other partition to gain access. To do this the user must first
press and hold the [#] key for two seconds. The keypad will go blank. The user must then press and hold the [1]
key for partition 1 or the [2] key for partition 2 for two seconds. The keypad will then display the status of the
selected partition and allow normal access.
3.7

Features Available for the LCD5500Z

These features are only available for LCD5500Z keypads with zone inputs:
Automatic Scrolling of Alarms in Memory
The LCD5500Z keypad allows automatic scrolling through alarms in memory while the keypad is idle. This feature, if
enabled, will override the clock display. This option can be programmed in LCD programming section [66], option [4].
24-Hour Time Display Option
The LCD5500Z can be programmed to display time using a 24-hour clock, instead of a 12-hour clock. This option
can be programmed in LCD programming section [66], option [3].
Keypad Zones
See section 2.10 "Keypad Zones".
Viewing Troubles While Armed
See section 3.4 "[✱][2] Trouble Display" for information on how to view troubles.
Backlighting Boost (available for all zone input keypads)
The LCD5500Z , LCD55001Z and PC55XXZ zone input keypads will provide extra number pad lighting when any
key is pressed. The backlighting boost will last for an additional 30 seconds after the last keypress.
Prompts for the following features are only supported by LCD5500(Z) v2.X and higher:
• Downlook support (DLM-4L/PC5108L): active camera monitor selection, remote trigger
• Auto-arm features: late to close, Auto-arm postpone/cancel, Auto-arm by day
• Bypass groups
A D C
Code Required for Bypass Code Required for Bypass
Code Required for Bypass option. If the option is enabled, a valid Code Required for Bypass
19
O M M A N D S
Code Required for Code Required for
Code Required for Code Required for