Sony DMX-R100 Operating Instructions Manual page 95

PRE (prefader) button: Selects the signal of the point
located before the CUT switch of the input signal path.
PST (post fader) button: Selects the signal of the
point located before the pan of the input signal path.
For AUX send, MTR bus and PGM, the signal after the
master fader is selected.
PEAK HOLD button
Selects the method used to display the peak hold level
of the input signals.
MAN (manual) button: Touch this button to always
display the maximum level of the input signal
(peakhold status). Touch this button again to cancel the
display of the peakhold status.
AUTO button: Touch this button to display the peak
level of the input signal for three seconds, and the hold
display is automatically reset.
3 MTR BUS MODE section
Touch the button to display SURROUND. When
SURROUND is displayed, the MTR bus is set to
surround mode. When the display is off, the MTR bus
is set to mono/stereo mode.
In 2 FS mode, the display is fixed to OFF. In 2 FS
surround mode, the display is fixed to ON.
4 TOUCH SENSOR section
Sets the sensitivity of the fader touch sensor.
SENSITIVITY display: Displays the sensitivity as
steps of 0 to 15. The maximum sensitivity is 15. To
increase or decrease the sensitivity, touch the display
box and set the value using the ten key pad or the jog
dial.
TOUCH display: The characters "TOUCH" appear in
red when any one fader is touched. They appear in
white when all faders are untouched.
KEEP button: Touch this button to store the
sensitivity on the SENSITIVITY display window in
the current title. At the same time, data in the work
area is also stored in the current title.
To adjust the sensitivity of the touch sensor
The fader sensitivity may deteriorate with use. If a
fader fails to store/recall the automation data, or if the
sound level does not change when you move a fader
manually, adjust the sensitivity of the touch sensor as
follows.
1
Touch the sensitivity display in the TOUCH
SENSOR section in the MISC SETUP window.
2
By using the – key or the jog dial, decrease the
sensitivity until "TOUCH" appears in white.
Be care not to touch a fader while performing
operations of steps from 2 to 4.
3
By using the + key or the jog dial, increase the
sensitivity to the value just where "TOUCH"
appears in red.
4
Press the – key twice.
The sensitivity is lowered by 2 units more than the
level set in step 3.
5
Touch all faders one by one, and confirm that
"TOUCH" appears in red, when you touch a fader.
• If the characters do not appear in red, increase the
sensitivity value by 1.
• If the characters occasionally appear in red,
decrease the sensitivity by 1.
• The touch sensor sensitivity has been set to 7 or 8
at the factory.
6
After confirming that the characters appear in red
only when you touch a fader, touch the KEEP
button.
The sensitivity value is stored in the unit.
7
Touch multiple faders at one time, and confirm that
"TOUCH" appears in red, when you touch the
faders.
5 DIM LEVEL section
CR MON is for control room monitors and STUDIO
LS is for studio monitors. To adjust the dim level of
the monitor signals, touch the display box and set the
value uisng the ten key pad or the jog dial.
KEEP button: Touch this button to store the dimmer
level displayed on the window in the current title. At
the same time, data in the work area is also stored in
the current title.
6 MASTER 0 dB section
When the PGM, MTR, AUX button is ON, the master
fader of each bus is fixed to 0 dB.
7TOUCH PANEL section
Calibrates the touch panel.
When the cursor does not move correctly, calibration
of the touch panel is required.
Touch the button to open the calibration window.
95
Chapter 3 Menu