Jumper Settings And Connectors - SOYO SY-6BB User Manual

Appendix: Quick Start Guide
3

Jumper Settings and Connectors

CMOS Clear: Power On by
JP5 Keyboard: JP50
Retain Pin 5VSB
CMOS data Support
1-2
(default)
Pin
Clear CMOS VCC
data (disable)
2-3
USB TB LED
Connect your Connect your
USB devices to Turbo LED to this
this header jumper
IrDA (Infrared Device
Connector): IR
Connect your IrDA device to
this connector
4
Memory configuration
Your board comes with three DIMM sockets, providing support for up
to 384MB of main memory using DIMM modules from 8MB to
128MB. For 66MHz host bus CPUs use 12ns or faster DIMM
modules; for 100MHz host bus CPUs use 8ns modules.
Memory configuration Table
Number of
Memory DIMM 1 DIMM 2 DIMM 3
Modules
1
2
rd
3
3
Note: It is of prime importance that you install DIMM
modules as outlined in the table above in order to preserve
signal integrity on 100MHz host bus systems.
6 CPU Settings
Enter the BIOS Setup Utility [CHIPSET FEATURES SETUP] section and configure the CPU frequency settings to match the
working frequency of your Pentium
Step 1.
Press the [Delete] key during boot up. In BIOS
select the [CHIPSET FEATURES SETUP]
menu.
Step 2. Note the working frequency of your Pentium
II processor that should be clearly marked on
the CPU cover.
Step 3. In [CHIPSET FEATURES SETUP], move the
cursor to the CPU Speed field.
Step 4. Configure the CPU Speed field in BIOS by
selecting the CPU frequency that matches the
working frequency your processor, as shown in
the following figure.
PCI Audio Card Connector: SB-Link ™
Pin Some PCI audio cards needs a DMA
channel. Connect the cable to SB-Link ™ .
2-3
Pin Wake-On-LAN Jumper: JP44
Connect the WOL cable from your LAN card to JP44.
1-2
SPK
Connect the speaker
cable to this jumper
AT Power Supply
Connect the AT Power Supply
header to this connector
rst
1
nd rst
2 1
nd rst
2 1
®
II processor. Follow these steps to configure the CPU settings:
RESET
Connect the reset
button to this jumper
ATX Power On/Off: PWRBT
Connect your power switch to this
jumper (momentary switch type)
5
Default I/O Settings
Default settings for multi-I/O addresses are as
follows:
Port
LPT1
COM1
COM2
Note:
other I/O cards such as sound card, you must
change one of the I/O addresses to remedy to this
address conflict. (I/O addresses can be adjusted
from the BIOS Setup Utility under [Integrated
Peripherals].)
CHIPSET FEATURES SETUP
Auto Configuration
SDRAM CAS latency Time
® DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15M-16M
Passive Release
Delay Transaction
AGP Aperture Size (MB)
Spread Spectrum Modulated
66
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin 1 2
Function GND 12V
IDE LED KB-LOCK
Connect the IDE Connect the Power
device LED to this LED and the KB
jumper Lock switch to
ATX Power Supply: ATX PW
Attach the ATX Power Supply
to this connector
I/O Address IRQ
378H 7
3F8H 4
2F8H 3
If a default I/O address conflicts with
ROM PCI/ISA BIOS
AWARD SOFTWARE, INC.
: Enabled CPU Speed : 133MHz (66 x 2)
: 3
: Non-ECC
: Disabled
CPU Warning Temperature
: Disabled
Current CPU Temperature
: Disabled
Current System Temp.
: 1
Current CPUFAN Speed
: 1
Current PWRFAN Speed
: Disabled
Current CHSFAN Speed
: Enabled
VID(V) : 2.78 V VTT(V)
: Enabled
3.3(V) : 3.31 V +5 (V)
: 64
+12(V) : 11.84V -12 (V)
: Disabled
-5(V) : -4.88V
↑ ↓ → ←
ESC : Quit
F1 : Help PU/PD/+/-
F5 : Old Values (Shift) F2
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
SY-6BB
3
Sensor
Status
ECP + EPP
: Disabled
° °
: 29 C/84 F
: 24 ° C/75 ° F
: 6553 RPM
: 6553 RPM
: 6553 RPM
: 1.50V
: 4.97V
: -11.45V
: Select Item
: Modify
: Color