Operations; Listening To A Program Source - Sherwood RD-705i Operating Instructions Manual

RD-705i(G)_ENG_101206_RD-705i(G)_ENG 2010-12-07 오전 10:24 페이지 15

Operations

■Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup
procedures. (For details, refer to "System Setup" on page 41.)

LISTENING TO A PROGRAM SOURCE

Before operation
• Enter the standby mode.
• The STANDBY indicator lights up.
This means that the receiver is not
disconnected from the AC mains and a small
amount of current is retained to support the
operation readiness.
• To switch the power off, push the POWER
switch again.
• Then the power is cut off and the STANDBY
indicator goes off.
1.
In the standby mode, turn the power on.
ON / STANDBY
• Each time the POWER ON/STANDBY button on the front
panel is pressed, the receiver is turned on to enter the
operating mode or off to enter the standby mode.
• On the remote control, press the POWER ON button to
enter the operating mode or press the STANDBY button to
enter the standby mode.
2.
Switch the speakers on.
• Then "SPEAKER ON" is displayed and the sound can be
heard from the speakers connected to the speaker
terminals.
• When using the headphones for private listening, press the
SPEAKER button again to switch the speakers off
("SPEAKER OFF" is displayed).
3.
Select the desired input source.
INPUT
VIDEO AUDIO
POWER
ON
BAND
• Each time the "VIDEO" button on the front panel is
pressed, the input source changes as follows:
→ VIDEO 1 → V2/iPOD → VIDEO 3 → VIDEO 4
• Each time the "AUDIO" button on the front panel is
pressed, the input source changes as follows:
→CD → AUX→ TV*→ F.AUX→ NET/USB →Tuner
OFF
* : Only when the HDMI CONTROL is set to ON, you can
hear the digital audio signals from TV via a HDMI cable.
(For details, refer to "When selecting the HDMI
CONTROL" on page 58.)
• When selecting NET/USB, refer to "LISTENING TO
INTERNET RADIO BROADCASTS, MUSIC FILES" on
page 28.
• Each time the BAND button(or the TUNER button on the
remote control) is pressed, the band changes as follows:
→ FM STEREO → FM MONO → AM
When an input source other than TV, NET/USB, tuner
is selected
• To hear the sound from the selected digital input, you
should set the AUDIO MODE correctly on the INPUT
SETUP menu. (For details, refer to "SETTING THE
INPUT SETUP" on page 45.)
4.
Select the digital or the analog input connected as desired.
AUDIO ASSIGN
RETURN
• Each time this button is pressed, the corresponding input
is selected as follows:
→ OPTI.1 → OPTI.2 → COAX.1 → COAX.2 → ANALOG
■Notes :
• When VIDEO 1 ~ 3 is selected and the corresponding HDMI IN
is connected, the digital input cannot be selected depending on
the AUDIO MODE setting ("AUTO", "HDMI").
• When TV, NET/USB or tuner is selected as an input source, the
digital input cannot be selected.
• The selected digital input or analog input is automatically
assigned to the corresponding input source on the INPUT setup
menu. (For details, refer to "SETTING THE INPUT SETUP" on
page 45.)
• The sound from the component connected to the selected digital
input can be heard regardless of the selected input source.
• When the selected digital input is not connected, this unit
operates as follows depending on the AUDIO MODE setting.
* If the AUDIO MODE is set to "AUTO", the "D" or "HDMI" flickers
and the analog input is automatically selected.
* If it is set to "DIGITAL" or "HDMI", "OPTI.1", etc or "HDMI1", etc
flickers, meaning no sound is heard.
15
(Frequency display)