Media; Ribbon - TEC B-880 series User Manual

2. SPECIFICATIONS

2.3 MEDIA

I
Stop
position
Cut
position
J
H
Item
Span of one label/tag
A :
: Label length
B
: Width including backing paper
C
: Label width
D
: Gap length
E
: Black mark length (Tag paper)
F
: Effective print width
G
:
H
Label
Effective
print length
Tag
: Print speed up/slow down area
I
: Black mark length (Label)
J
Maximum effective
length for on the fly
issue
Outer roll diameter
Label
Thickness
Tag
NOTES: 1. The media specification other than above are unchanged.
2. When marking black marks on label rolls, the following requirements must be satisfied.
When the gap length is less than 4 mm:
The black mark length should be longer than the gap length.
When the gap length is 4 mm or more:
The black mark should not overlap the gap for more than 4 mm and the following label.
3. When issuing thermal labels at 8"/sec., the print stop position should be set to a minimum of 1 mm inside the label.

2.4 RIBBON

Type Spool type
Width 115 mm ~ 224 mm
Length 300 m
Outer diameter Ø72 mm (max.)
Refer to the following
NOTE 2.
Black Mark
Label
(on reverse side)
E
Reference
coordinate
1
B
Reference
coordinate
2
G
D
C
Label dispensing mode
B-872
B-882
B-872
B-882
B-872
Standard
B-882
Max. memory
B-872
B-872
Standard
B-882
Max. memory B-872
B-872
Standard
B-882
Max. memory
B-872
NOTES: 1. "On the fly issue" means that the printer can draw and print without stopping
between labels.
2. To ensure print quality and print head life use only TOSHIBA TEC specified
media and ribbons.
3. When using the cutter ensure that label length B plus inter label gap length
E exceeds 35 mm. (i.e. label pitch should be greater than 35 mm.)
4. Use of rough media for the ribbon saving issue may cause ribbon smudges.
5. To avoid ribbon wrinkles use the ribbon which is wider than media by 5mm
or more. However, too much difference in width between the two may
cause wrinkles.
I
Stop
position
Cut
position
Reference
coordinate
A
H
Feed direction
Fig. 2-1
Batch mode Strip mode
10.00 ~ 999.0 25.4 ~ 999.0
10.00 ~ 1368.0 25.4 ~ 1368.0
7.5 ~ 996.5 22.9 ~ 996.5
7.5 ~ 1366.0 22.9 ~ 1366.0
101.6 ~ 225.0
98.6 ~ 222.0
2.5 ~ 20.0 2.5 ~ 20.0
2.5 ~ 10.0
10.0 ~ 213.3
5.5 ~ 320.0 20.9 ~ 320.0
5.5 ~ 1364.0 20.9 ~ 1364.0
5.5 ~ 661.3 20.9 ~ 661.3
8.0 ~ 320.0 23.4 ~ 320.0
8.0 ~ 1364.0
8.0 ~ 661.3 23.4 ~ 661.3
Refer to the following NOTE 2.
Ø200 Max.
0.13 ~ 0.17
0.10 ~ 0.17
2-3
Tag paper Black Mark
(on reverse side)
Tag paper
F
1
A
Reference
coordinate
2
G
C
[Unit: mm]
Cut mode
Label: 38 ~ 999.0
Tag: 25.4 ~ 999.0
Label: 38 ~ 1368.0
Tag: 25.4 ~ 1368.0
25.0 ~ 993.0
25.0 ~ 1362.0
6.0 ~ 20.0
23.0 ~ 320.0
23.0 ~ 1364.0
23.0 ~ 661.3
23.4 ~ 320.0
23.4 ~ 1364.0
23.4 ~ 661.3
1.0
160.0
682.0
330.6
EO1-33017
2.3 MEDIA