Trane Thermostats Installation And Operation Manual page 31

Table 7.
No.
(1) These options only available on systems with fans.
(2) See
(3) S ee
BAS-SVX36C-EN
Installation Options for 3-Heat/2-Cool Non-Programmable Thermostat
Name Default
01 System type 0
02 Changeover 0
valve
(1)
03 Fan control 0
04 Stage 1 heat 5
(2)
cycle rate
05 Stage 1 3
compressor cycle
(2)
rate
06 Manual/Auto 0
changeover
07 Temperature 0
indication/
resolution
08 Compressor 5
protection
09 Heat 90
temperature
range stop
10 Cool temperature 50
range stop
11 Power supply 0
frequency
(3)
12 Deadband 3
13 Stage 2 heat 9
(2)
cycle rate
14 Auxiliary heat 5
(2)
cycle rate
15 Emergency heat 5
(2)
cycle rate
16 Stage 2 3
compressor cycle
(2)
rate
17 Auxiliary heat 0
control
18 Restore factory 0
defaults
"Heat and Cool Cycling Rate," p.
"Deadband," p. 41. For auto or manual systems (see Option 01).
Opts. Descriptions
0 1H/1C, conventional - 1st stage heat (W), 1st stage
compressor (Y)
1 1H/1C, heat pump without auxiliary heat - 1st stage compressor (Y),
changeover (O/B)
2 1H, conventional without fan - 1st stage heat (W)
3 1H, conventional with fan - 1st stage heat (W), fan (G)
4 1C, conventional - 1st stage compressor (Y)
5 2H/1C, heat pump with auxiliary heat - 1st stage compressor (Y), changeover
(O/B), auxiliary heat (Aux/E)
6 2H/1C, conventional - 1st & 2nd stage heat (W,W2), 1st stage compressor (Y)
7 1H/2C, conventional - 1st stage heat (W), 1st & 2nd stage compressor (Y, Y2)
8 2H/2C, heat pump without auxiliary heat - 1st & 2nd stage compressor (Y,
Y2), changeover (O/B)
9 3H/2C, heat pump with auxiliary heat - 1st & 2nd stage compressor (Y, Y2),
changeover (O/B), auxiliary heat (Aux/E)
0 O/B terminal energized in cooling
1 O/B terminal energized in heating
0 Gas or oil furnace, equipment controls fan for heating
1 Electric furnace, thermostat controls fan in heating
1-10 Cycles per hour for 1st stage conventional heat - only available on systems
with conventional heat
1-5 Cycles per hour for 1st stage compressor - only available on systems with cool
stages
0 Manual changeover (heat/cool/off) - manually changeover between heat,
cool, and off
1 Auto changeover (heat/cool/auto/off) - manually changeover between heat,
cool, and off, or select automatic changeover
2 Auto changeover only (auto) - no manual changeover
0 °F with 1 degree resolution
1 °F with 0.5 degree resolution
2 °C with 1 degree resolution
3 °C with 0.5 degree resolution
4 °C with 0.1 degree resolution
0-5 Minutes for compressor off time - only available on heat pump systems or
systems with cool stages - (Minutes specified here are added to the 5 min
base off time.)
40-90 Heating high temperature range stop in °F. (4.5-32°C)
50-99 Cooling low temperature range stop in °F. (10-37°C)
0 60 Hz
1 50 Hz
2 2°F (1.0°C)
3 3°F (1.5°C)
4 4°F (2.0°C)
5 5°F (2.5°C)
6 6°F (3.0°C)
7 7°F (3.5°C)
8 8°F (4.0°C)
9 9°F (4.5°C)
1-10 Cycles per hour for 2nd stage conventional heat - only available for
conventional systems with at least two stages conventional heat
1-10 Cycles per hour for auxiliary heat - only for heat pump systems with more
heat than cool stages
1-10 Cycles per hour for emergency heat - only for heat pump systems with more
heat than cool stages.
1-5 Cycles per hour for 2nd stage compressor - only for systems with two cool
stages
0 Comfort
1 Economy
0 No - do not reset
1 Yes - reset all installation configurations (all settings in this table) to default
settings, except System selection
41.
Configuration
31