Toshiba TOSVERT VF-AS1 Instruction Manual page 246

[5] V/f 5-point setting
Communi
Title cation Function
No.
V/f 5-point setting VF1
0190
frequency
0191 V/f 5-point setting VF1 voltage
V/f 5-point setting VF2
0192
frequency
0193 V/f 5-point setting VF2 voltage
V/f 5-point setting VF3
0194
frequency
0195 V/f 5-point setting VF3 voltage
V/f 5-point setting VF4
0196
frequency
0197 V/f 5-point setting VF4 voltage
V/f 5-point setting VF5
0198
frequency
0199 V/f 5-point setting VF5 voltage
[6] Speed/torque reference gain/bias setup [1/2]
Communi
Title cation Function
No.
0200 Frequency priority selection
0201 VI/II input point 1 setting
0202 VI/II input point 1 frequency
0203 VI/II input point 2 setting
0204 VI/II input point 2 frequency
0205 VI/II input point 1 rate
0206 VI/II input point 2 rate
Frequency setting mode
0207
selection 2
Speed command priority
0208
switching frequency
0209 Analog input filter
0210 RR/S4 input point 1 setting
0211 RR/S4 input point 1 frequency
This parameter moves to a fundamental parameter.
*1: Inverter with a model number ending with -WN: 60.0 -WP: 50.0
*2: ⇒ For details, refer to Instruction Manual (E6581331) specified in Section 6.41.
Adjustment range
0.0~ Hz
0.0~100.0%
0.0~ Hz
0.0~100.0%
0.0~ Hz
0.0~100.0%
0.0~ Hz
0.0~100.0%
0.0~ Hz
0.0~100.0%
Adjustment range
0: / terminal switching (input
terminal function selection 104, 105)
1: / frequency switching (switching
with )
0~100%
0.0~ Hz
0~100%
0.0~ Hz
0~250% (for torque control etc.)
0~250% (for torque control etc.)
Same as (1~13)
0.1~ Hz
0:No filter
1:Filter approx. 10ms
2:Filter approx. 15ms
3:Filter approx. 30ms
4:Filter approx. 60ms
0~100%
0.0~ Hz
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
setting unit Default Write during
Speed
(Panel/Communi setting running
control
cation)
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
0.1/0.01 0.0 Disabled -
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum Vector control
Write during
setting unit Default
running Speed
(Panel/Communi setting
control
cation)
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
1/1 100 Enabled ●/●
0.1/0.01 *1 Enabled ●/●
1/0.01 0 Enabled ●/●
1/0.01 100 Enabled ●/●
1/1 ‚ P Disabled ●/●
0.1/0.01 0.1 Enabled ●/●
1/1 0 Enabled ●/●
1/1 0 Enabled ●/●
0.1/0.01 0.0 Enabled ●/●
PM
Torque V/f Reference
control
control
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
- ● ● 5. 6
PM
Torque V/f Reference
control
control
- ● ● 6. 6. 1
●/● ● ● 7. 3. 2
- ● ● 7. 3. 2
●/● ● ● 7. 3. 2
- ● ● 5. 11
●/● - - *2
●/● - - *2
- ● ● 6. 6. 1
- ● ● 6. 6. 1
●/● ● ● 7. 2. 4
●/● ● ● 7. 3. 1
- ● ● 7. 3. 1