Tuning Terrestrial Television Channels (Dvb-T); Tuning Television Channels From The Cable Provider (Dvb-C) - Grundig FineArts ­55 ­FLE ­9170 ­SH User Manual

SEttINGS
­-----------------------------------------------------------------------------------------------------------------------------------------
tuning­terrestrial­television­
channels­(DvB-t)
1 In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Air« with
< >
» « or » «.
2 Select the line »Scan Type« with »
» «.
Λ
< >
Use » « or » « to set the required scan
type:
– » DTV«, scan for digital television channels;
– » ATV«, scan for analogue television
c hannels;
– » ATV & DTV«, scan for analogue and
d igital television channels.
Caution:
The antenna power supply (5V ) may only
7
be switched on if the antenna is an active
i ndoor antenna with a signal amplifier and it
is not already supplied with a voltage via a
mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
3 Select the line »Active Antenna Power« with
» « or » «.
v Λ
Switch on the antenna power supply for the
<
antenna with » « or »
4 Start the scan with »
– T he »Search Results« menu appears, and
the search for TV channels begins.
– D epending on the number of television
channels received, this can easily take a
few minutes.
– T he scan is complete as soon as the »PRO-
GRAM TABLE« appears.
Note:
You can abort the scan by pressing
7
»mENu«.
5 Press »mENu« to end the setting.
Note:
B efore recording HD channels, please
7
check signal quality and Strength, see
chapter "Displaying signal information" on
page 72. If the level is displayed in green,
you can record HD channels without any
problems.
« or
v
>
« (»On«).
« (green).

tuning­television­channels­from­
the­cable­provider­(DvB-C)
1 In the »Source Setup« menu, in the »Connec-
tion Type« line, select the option »Cable«
< >
with » « or » «.
2 S elect the line »Scan Type« with »
< >
Use » « or » « to set the required scan type:
– » DTV«, scan for digital television channels;
– » ATV«, scan for analogue television c hannels;
– » ATV & DTV«, scan for analogue and
d igital television channels.
3 Select the line »Cabel Scan Type« with »
or » «. Select the preferred option (»Quick«
Λ
<
or »Full«) with » « or »
– T he search function »Quick« sets up the
channels according to the information pro-
vided by your cable provider in the trans-
mission signal.
– I f the option »Full« is selected, the entire
frequency range will be scanned. The
search can take a long time with this op-
tion. This option is recommended if your
cable provider does not support the scan
type »Quick«.
Note:
You can accelerate the search. To do this,
7
you need information about the frequency
and network ID. You are usually able to get
this data from your cable operator or find it
in forums on the Internet.
4 Start the scan with »
– T he »Search Results« menu appears, and
the search for TV channels begins.
– D epending on the number of television
channels received, this can easily take a
few minutes.
– T he scan is complete as soon as the »PRO-
GRAM TABLE« appears.
Note:
You can abort the scan by pressing
7
»mENu«.
5 Press »mENu« to end the setting.
Note:
B efore recording HD channels, please check
7
signal quality and Strength, see chapter
"Displaying signal information" on page 72.
If the level is displayed in green, you can
record HD channels without any problems.
« or »
v Λ
v
>
«.
« (green).

ENGLISH
«.
«
­ 1 5