Quadra-Fire 41I-ACC Owner's Manual page 2

41I ACC Wood Insert
Hearth & Home Technologies welcomes you to our tradition
of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and
performance.
This commitment begins with our research of the market,
including 'Voice of the Customer' contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world's most
advanced technology to achieve the optimum operation
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
Test Lab & Report
Number
Page 2
and Welcome to the Quadra-Fire Family
SAMPLE OF SERIAL NUMBER / SAFETY LABEL
LOCATION: UNDER ASH LIP ON PULL-OUT PLATE
LISTED ROOM HEATER, SOLID FUEL TYPE. "For Use with Solid
Wood Fuel Only." Also for use in Mobile Home.
Install and use only in accordance with manufacturer's installation, venting and operating
instructions.
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND
INSTALLATION INSPECTION IN YOUR AREA
Refer to manufacturer's instructions and local codes for precautions required for passing
chimney through a combustible wall or ceiling.
WARNING - For Mobile Homes: Do not install in a sleeping room. An outside
combustion air inlet must be provided and unrestricted while unit is in use. The structural
integrity of the mobile home floor, ceiling and walls must be maintained. The insert must
be properly grounded to the frame of the mobile home. A complete relining of the chimney
system with a 6 inch (152mm) diameter listed stainless liner is required. Must be
equipped with a spark arrestor cap. Outside Air comes standard on the insert and must be
installed before operating insert.
When used as a masonry insert stove, install only in a masonry fireplace built to national
and/or local codes. Do not remove brick or mortar to accommodate insert. Installation
requires a 5 foot minimum length of a starter pipe into existing chimney with airtight face
seal.
Install only on a non-combustible hearth. Approved for installation and use in factory built
zero-clearance fireplaces conforming to minimum fire chamber specifications.
Components required for installation: positive or direct flue connection assembly or listed
vent liner.
In Canada a full length
WARNING - Inspect and clean chimney frequently. Under certain conditions of use,
creosote buildup may occur rapidly.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing. Route
power cord away from unit. Do not route cord under or in front of appliance.
Electrical Rating: 115 VAC 1.4 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on hearth (firebrick). Do not
overfire. If heater or chimney connector glows, you are overfiring. Operate only with doors
closed. Open only to add fuel to the fire.
Replace glass only with 5mm ceramic available from your dealer.
Minimum Clearances To Combustible Material
Masonry, Heat Circulating &
Refer to Clearances on other label for Canada
A Sidewall to Fuel Loading Door
B Mantel to Top of unit
C Top Trim to Top of unit
D Side Trim to Fuel Loading Door
E Hearth Extension from Glass
F Hearth Extenson from Fuel Loading Door
ETL4001508
TESTED TO:
UL 1482, ULC S628-93
Mfg by:
U.S. ENVIRONMENTAL PROTECTION AGENCY
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
2011 2012 2013
of our stoves, inserts and fireplaces. And yet we are old-
fashioned when it comes to craftsmanship. Each unit is
meticulously fabricated and gold and nickel surfaces are
hand-finished for lasting beauty and enjoyment. Our pledge
to quality is completed as each model undergoes a quality
control inspection.
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
PREVENT HOUSE FIRES
6 inch (152mm) S635 flue liner is required as per ULC S628-93.
Maximum Mantel Depth - 12 inch (305mm)
Mantel
B
Fascia or Trim
C
Insert
A
D
Fuel Door
E
F
Hearth Extension
Factory-Built Floor
Protection under Hearth
Factory-Built
Extension
Thermal & Ember Protection
Floor height 0 to 1-3/4 inches
USA ONLY
22 in.
below Insert Base:
23 in.
1/2 inch R=2.38
21 in.
11 in.
Ember Protection Only
16 in.
Greater than 1-3/4 inches
8 in.
below Insert Base:
CAUTION:
HOT WHILE IN
OPERATION DO NOT
TOUCH, KEEP CHILDREN, CLOTHING AND
FURNITURE AWAY. CONTACT MAY CAUSE
SKIN BURNS. SEE NAMEPLATE AND INSTRUC-
TIONS.
R
Serial No.
007027
Model:
41I-ACC
WOOD INSERT
1445 N. Highway, Colville, WA 99114 www.quadrafire.com
standards.
- Certified to comply with July 1990 particulate emission
DO NOT REMOVE THIS LABEL
Made in U.S.A. of US and
imported parts.
7045-179
7045-178
!
Serial Number
Model Name
Mfg Date
September 15, 2011
R