Pioneer LX01BD Operating Instructions Manual page 96

Problem
07
Picture is stretched.
Aspect ratio cannot be
switched.
Sound and picture are not
synchronized.
Picture is disturbed during
playback.
Picture is dark.
No picture is displayed or
picture is not output in high
definition when playing BDs.
No sound is output.
Sound is disturbed.
Multi-channel sound is not
output.
96
En
Check
Is the TV's aspect ratio properly set?
Is 4:3 Video Out properly set?
Is Output Terminal Priority properly set?
Is the disc played back in slow motion?
Is the disc played back in fast forward or fast reverse?
Is the disc scratched?
Is the disc dirty?
Is the player properly connected to the other components (AV
receiver or amplifier, etc.)?
Are the connected components (AV receiver or amplifier, etc.)
properly set?
Are the audio cables properly connected?
Is the audio cable damaged?
Is Audio Output Mode properly set?
Are the speakers properly set?
Is the AV receiver or amplifier, etc. connected to the HDMI
OUT terminal, the AUDIO OUT (7.1 ch) terminals or DIGITAL
OUT (OPTICAL) terminal?
Is Output Terminal Priority properly set?
Is the audio output of the connected AV receiver or amplifier,
etc., properly set?
Is multi-channel sound selected?
Is Audio Out set to audio formats supported by the connected
AV receiver or amplifier?
Are Audio Output Mode and Speaker Setup properly set?
Remedy
Read the TV's operating instructions and set the TV's aspect
ratio properly.
• Set 4:3 Video Out properly (page 82).
• When video signals with a resolution of 1080/50i, 1080/50p,
720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are being
output from the HDMI OUT terminal or the COMPONENT
VIDEO output terminals, they may be output with an aspect
ratio of 16:9 even if TV Aspect Ratio is set to 4:3 (Standard)
(page 65).
Set Output Terminal Priority properly (pages 62 and 89).
• This player supports Macrovision analog copy protection
technology. With some TVs (such as with built-in video deck),
the picture will not be displayed properly when the copy
protected DVD title is played. This is not a malfunction.
• If the player and TV are connected via a DVD recorder/video
deck, etc., the picture will not be displayed properly due to
analog copy protection. Connect the player and TV directly.
With some content protected discs, it may not be possible to
output the video signals from the VIDEO output terminals, the
S-VIDEO output terminal or the COMPONENT VIDEO output
terminals. In this case, connect using an HDMI cable
(page 91).
No sound is output during slow motion play and forward and
reverse scanning.
The sound may not be output if the disc is scratched.
Clean the disc (page 103).
• Check that you connect the player to the audio output
terminals of a different component, etc.
• Check that you connect the player to the PHONO input
terminals of the AV receiver or amplifier, etc.
Read the operating instructions of the connected components
and check the volume, input, speaker settings, etc.
Insert the cables firmly and all the way in.
If the cable is damaged, replace it with a new one.
If Audio Output Mode is set to Multi-channel, the audio
signals may not be output properly from the AUDIO OUT (2
ch) terminals (page 82). Set Audio Output Mode to 2
Channel.
Set Speaker Setup properly (page 82).
For some BDs, audio signals are only output from the optical
digital audio output terminal or the HDMI output terminal.
Read the operating instructions of the connected AV receiver
or amplifier and check the audio output settings of AV receiver
or amplifier.
Linear PCM (2-channel) audio signals are output from output
terminals other than the one set at Audio under Output
Terminal Priority. Set Output Terminal Priority properly
(page 89).
Read the operating instructions of the connected AV receiver
or amplifier and check the audio output settings of AV receiver
or amplifier.
Use the menu screen or AUDIO to switch the disc's sound to
multi-channel.
• Read the operating instructions of the connected AV receiver
or amplifier and check the supported audio formats.
• Set Audio Out properly (page 82).
• When the AV receiver or amplifier, etc., is connected to the
AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to
Multi-channel (page 82).
• Set Speaker Setup properly (page 82).