Pioneer LX01BD Operating Instructions Manual page 66

The output video resolution can be switched by selecting Output
02
Video Resolution from the TOOLS menu.
The output video resolution depends on the video output terminal.
See the table below.
The table below shows the output video resolution for the different
terminals when the frame/field frequency of the playback source is
50 Hz on the upper line, the resolutions when the source's frame/
field frequency is 60 Hz on the lower line.
Output HDMI OUT
video terminal
resolution
setting
Resolution
2
Auto
preferred by TV
576i or 576/50i
480i
480/60i
576p or 576/50p
480p
480/60p
1080i 1080/50i
1080/60i
2 7
1080p 1080/50p
7
1080/60p
Source Resolution
Direct recorded on
3,8,9
disc
1. Depending on the BD, the pictures may not be output.
2. Cannot be selected when the video signals are being output from the
COMPONENT VIDEO output terminals, S-VIDEO output terminal or the
VIDEO output terminal.
3. For details on the output of film material (1080/24p or 720/24p video signals),
see To output film material below.
4. Sources with a resolution of 720/50p, 720/60p and 720/24p are output at 1080/
50i or 1080/60i, even if the TV's preferred resolution is 1080/50p or 1080/60p.
5. Depends on the NTSC on PAL TV setting (page 82).
6. DVD-Video or DVD VR format is output at 480/60p. BDs format may be output
at 480/60p.
7. Depending on the connected HDMI cable, the video signals may not be
output. Also, sources with a resolution of 720/50p is output at 1080/50i, and
720/60p and 720/24p are output at 1080/60i.
8. Depending on the connected TV, the video signals may not be output.
9. 720/24p film material is output at 720/60p.
10. 1080/24p film material is output at 1080/60i.
Caution
• On some TVs, the picture may not be displayed properly when the
resolution is switched. If this happens, use RESOLUTION / to
set to a resolution at which the picture is properly displayed.
• When video signals are being output with a resolution of 1080/
50i, 1080/50p, 720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p
from the HDMI output terminal or component video output
terminals, the picture may be output with an aspect ratio of 16:9,
even if the TV Aspect Ratio is set to 4:3 (Standard).
• The picture may not be displayed for a while when the resolution
is switched.
 About the frame/field frequency and NTSC/
PAL TV systems
By factory default setting, the frame/field frequency is set for an
output of 50 Hz, and the video signal output from the S-VIDEO and
VIDEO output terminals is set to be output in the PAL TV system
66 format. When sources with a frame/field frequency of 60 Hz or
24 Hz are played, the output frame/field frequency automatically
En
COMPONENT S-VIDEO/
VIDEO VIDEO
output output
1 1
terminals terminal
— —
3,4
576/50i 576/50i
480/60i 480/60i
576/50p 576/50i
480/60p 480/60i
576/50p 576/50i
6 480/60i
1080/60i
— —
Resolution 576/50i
recorded on
480/60i
8,9,10
disc
switches to 60 Hz (or 24 Hz for HDMI, depending on the setting), and
the TV system format for the video signal output from the S-VIDEO
and VIDEO output terminals is set to NTSC on PAL TV. When
playback is stopped, the frame/field frequency and TV system
settings remain at the settings last used. The frame/field frequency
and TV system settings do not change even when the power is
turned off. They only switch when a video material with a different
frame/field frequency is played.
If the picture is not displayed on the TV when a source with a
TV
different frame/field frequency is played, use the procedure below to
system
switch the frame/field frequency and TV system settings for the
signal output from the player.
Eject the disc, then press the  OPEN/CLOSE button on the front
PAL
panel while pressing the  PLAY button to switch to a different
 5
frame/field frequency. The frame/field frequency switches between
50 Hz and 60 Hz each time this operation is performed. The indicator
PAL
for the frame frequency's current setting lights on the front panel
 5
display (page 17).
PAL
 About Film material
 5
The film material is a video signal with a frame rate of 24 frames/
PAL
second. For example, these materials include 1080/24p, 720/24p,
 5
etc.
PAL
Example:
 5
Output Video Resolution
PAL
 5
 To output film material
To output 1080/24p film material from the HDMI output terminal, set
the output video resolution to either Auto or Source Direct.
Caution
• 1080/24p signals can only be output from the HDMI OUT
terminal. They cannot be output from other video terminals.
• When Auto is selected, the picture is output at 60 frames/
second if your TV is not compatible with 1080/24p signals.
• When Source Direct is selected, the signals are output as such,
even if your TV is not compatible with 1080/24p signals. If the
picture is not displayed properly, use RESOLUTION / to set
to the output video resolution at which the picture is properly
displayed.
• 720/24p video signals are output at 60 frames/second, even if
the resolution is set to Auto or Source Direct.
Video resolution of the
currently playing disc
Source : 1080/24p
Auto
Current Output : 1080/24p
Output video resolution
from the player