Sharp SF-2530 Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Copier
  5. SF-2530
  6. Operation manual

Sharp SF-2530 Operation Manual

Plain paper copier
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL
SF-2530
PLAIN PAPER COPIER
OPERATION MANUAL
GETTING STARTED
MAKING COPIES
STATUS INDICATORS
GENERAL INFORMATION
OPTIONAL EQUIPMENT
Page
2
8
22
30
53

Advertisement

Table of Contents
loading

Related Manuals for Sharp SF-2530

Summary of Contents for Sharp SF-2530

  • Page 1 MODEL SF-2530 PLAIN PAPER COPIER OPERATION MANUAL Page GETTING STARTED MAKING COPIES STATUS INDICATORS GENERAL INFORMATION OPTIONAL EQUIPMENT...
  • Page 2 To protect against loss or theft, record and retain for reference the copier’s serial number located on the right hand side at the rear bottom corner of the copier. SF-2530 Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number...

  • Page 3: Table Of Contents

    CONTENTS Page INTRODUCTION GETTING STARTED The SF-2530 has been designed to give INSTALLATION REQUIREMENTS ....2 high productivity while offering convenient CAUTIONS ........3 copying features. Its main features are: LOADING COPY PAPER ...... 4 Easy operation, ADDING TONER ......6...

  • Page 4: Installation Requirements

    INSTALLATION REQUIREMENTS To ensure safety and proper machine performance, please note the following before initial installation and whenever the machine is to be relocated. The copier should be installed near an accessible power outlet for easy connection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

  • Page 5: Cautions

    CAUTIONS Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty copies. The fusing unit is extremely hot. Exercise care in this area. Fusing unit Photoconductive drum Installation adjusters are provided on the optional stand/ 500-sheet paper drawer or stand/1000-sheet paper drawer.

  • Page 6: Loading Copy Paper

    8-1/2" x 14", and 11" x 17". improperly installed. The 1000-sheet paper drawer can be adjusted for For best results, use only Sharp recommended paper. three different paper sizes: 8-1/2" x 11", 8-1/2" x 11"R, The copy paper size for the 500-sheet paper drawer and 8-1/2"...
  • Page 7 LOADING COPY PAPER Changing the lower paper tray’s inner cassette The lower paper tray can accommodate five different paper sizes. To change the paper size, simply change the inner cassette. (The inner cassettes are optional.) Gently lift and pull out the lower paper tray. Grasp the inner cassette tabs and remove the cassette.

  • Page 8: Making Copies

    For best copying results, be sure to The toner required ( ) indicator will light up when toner use only Sharp Genuine Supplies concentration level in the developer unit is low. If copying is which are designed, engineered, and continued while the...

  • Page 9: Adding Toner

    ADDING TONER Place the new toner cartridge with the tabs in the notches as shown. Slide the toner cartridge along the guides over the toner hopper. Hold the toner cartridge with one hand while pulling on the sealing tape to remove it. Sealing tape Tap on the top of the toner cartridge 5 times to release all toner into the toner hopper.

  • Page 10: Auditing Accounts

    AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 37 for setting the auditing mode. If the copier has been programmed in the auditing mode, “––” will appear in the copy quantity display in the initial conditions.

  • Page 11: Normal Copying

    NORMAL COPYING One-sided copying Turn the power switch on. It will take about 60 seconds for the copier to warm up. After warm-up, the START key indicator will light up, indicating that Power on copying is possible. If the copier has been programmed in the auditing mode, the START key indicator will not light up and “––”...
  • Page 12 NORMAL COPYING For manual copy density adjustment, press the EXPOSURE key to select MANUAL and adjust with the LIGHT and DARK 1 2 3 4 5 keys as desired. EXPOSURE AUTO MANUAL PHOTO LIGHT DARK 1 2 3 4 5 LIGHT DARK For photographs, select PHOTO and then adjust with the LIGHT...

  • Page 13: Two-Sided Copying With Optional Duplex Module

    NORMAL COPYING Two-sided copying with optional duplex module Two-sided copies can be made by pressing the ORIGINAL TO COPY key when an optional duplex module is installed. Place the first original face down on the document glass and close the document cover. ODD NUMBER Press the ORIGINAL TO COPY key to select EVEN NUMBER.

  • Page 14: Using The Manual Feed Tray (Special Paper)

    USING THE MANUAL FEED TRAY (special paper) The manual feed tray is used to copy onto transparency film, labels, tracing paper, and other special purpose papers. Up to 50 sheets of standard copy paper can be set in the manual feed tray. Automatic duplex copying will not work when a non-standard sized paper is used.

  • Page 15: Two-Sided Copying With Manual Feed Tray

    USING THE MANUAL FEED TRAY (special paper) Two-sided copying with manual feed tray Two-sided copies can be made using the manual feed tray. Place the first original face down on the document glass and make a copy. The first side of the copy can be made using any of the paper feed stations.

  • Page 16: Reduction/Enlargement/Zoom

    REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either auto- matically with the AUTO IMAGE key or manually with the reduction ) key, enlargement ( ) key, or ZOOM keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments.
  • Page 17 REDUCTION/ENLARGEMENT/ZOOM Manual Place the original face down on the document glass and close the document cover. Use the reduction ( ), enlargement ( ) and ZOOM ZOOM keys to set the desired copy ratio. A. Preset reduction ratios are: 95%, 77%, 64%, and 50%. EXTRA B.

  • Page 18: Dual Page Copying

    DUAL PAGE COPYING The DUAL PAGE COPY feature produces separate copies of two documents placed side by side on the document glass. It is especially useful when copying books and other bound documents and can be used with the MARGIN SHIFT feature. If an optional duplex module is installed, this feature can also be used with two- sided copying.

  • Page 19: Edge Erase

    EDGE ERASE Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. Place the original face down on the document glass and close the document cover. If an optional document feeder (ADF or RADF) is installed, place the originals face up in the document feeder tray.

  • Page 20: Margin Shift

    MARGIN SHIFT The MARGIN SHIFT feature automatically shifts the text or image to the right on one-sided copies to increase the left margin by ap- Original Copy proximate 1/4". If two-sided copying is made possible by using an optional duplex module, the image is shifted to the right on the front side of copies and to the left on the second side.

  • Page 21: Interrupting A Copy Run

    INTERRUPTING A COPY RUN INTERRUPT can be used to temporarily stop a long copy run so that another job can be run. Reduction/enlargement/zoom, exposure adjustments, dual page copying, edge erase, and margin shift can be selected during interrupt copying. Duplex copying, sort, group, and staple sort cannot be selected during interrupt copying.

  • Page 22: Automatic Exposure Adjustment

    AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. Ensure that the copier is in the AUTO exposure mode. IGINAL TO COPY EXPOSURE AUTO (ORIGINALS) MANUAL EVEN NUMBER PHOTO ODD NUMBER 1 2 3 4 5 PRE-COUNT Open the front cover.

  • Page 23: Toner Save Mode

    TONER SAVE MODE This mode reduces toner consumption, increasing cost effective- ness, with only a slight loss in copy density. Follow the procedure below for setting the toning level. Press the EXPOSURE key to select the PHOTO mode. IGINAL TO COPY EXPOSURE AUTO (ORIGINALS)

  • Page 24: Misfeed Removal

    MISFEED REMOVAL When a misfeed occurs, the copier will stop. If paper becomes accidentally torn during removal, The misfeed ( ) indicator will blink and blinking be sure to remove all pieces. Be careful not to red misfeed location indicators will indicate the damage the photoconductive drum or the corona approximate misfeed location.
  • Page 25 MISFEED REMOVAL Misfeed in a paper tray Open the side cover. NOTE: If the transport area misfeed indicator is lighted, clear the transport area first. (See below, “Misfeed in the transport area.”) Remove the misfed paper. Be careful not to tear the misfed paper during removal. If the paper cannot be seen from the side, pull out the paper tray and remove the misfed paper.
  • Page 26 MISFEED REMOVAL Turn the transport lever to the left. Transport lever Turn the roller rotating knob in the direction of the arrow to remove the misfed paper. Roller rotating knob Turn the transport lever back into place. Close the front cover. Confirm that the indicator has gone out.
  • Page 27 MISFEED REMOVAL Turn the roller rotating knob in the direction of the arrow and remove the paper from the fusing unit area. Roller rotating knob CAUTION The fusing unit is hot! Use care in removing paper. If the misfed paper is in the exit area, open the exit area cover carefully.
  • Page 28 MISFEED REMOVAL Misfeed in the duplex module The duplex module is optional. NOTE: If any other misfeed locations are indicated, be sure to remove any misfed paper from these locations before performing the procedure described below. If not, a sheet of paper in another location may become torn and difficult to remove.

  • Page 29: Used Toner Disposal

    Keep the full toner collecting container until the next regular service call. Your authorized Sharp Service Technician will collect the container for disposal. Install the new toner collecting container by pushing it down onto the spring-loaded tray and then allowing it to move upward and click into place.

  • Page 30: Developer Required

    When the developer replacement required ( ) indicator lights up, the developer should be replaced. DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your Service Center as soon as possible. NOTE: If the indicator and the copy quantity display blink simulta-...

  • Page 31: Maintenance Required

    MAINTENANCE REQUIRED When the maintenance required ( ) indicator lights up, service by an authorized Sharp Service Technician is required. Contact your Service Center as soon as possible.

  • Page 32: Part Names And Functions

    PART NAMES AND FUNCTIONS Exterior q Document holder !1 Power switch Press to turn copier power on and off. w Exit tray Finished copies are deposited in the exit tray. !2 Duplex module or 500-sheet paper drawer (optional) e Document cover (optional in some areas) The copier can be equipped with either a duplex Place the original on the document glass and module or a 500-sheet paper drawer.

  • Page 33: Interior

    PART NAMES AND FUNCTIONS Interior !8 Fusing unit Accessories The fusing unit is hot. Exercise care in this area. !9 Transport lever Inner cassette Turn to open the transport section. (installed in the lower paper tray) ....1 @0 Corona unit Exit tray ............

  • Page 34: Operation Panel

    (Can be When lit, indicates that the developer needs to be selected only when an optional replaced. Call your authorized Sharp Service ADF or RADF is installed.) Center. !7 LIGHT and DARK keys and indicators (p. 10)
  • Page 35 PART NAMES AND FUNCTIONS INTERRUPT CLEAR ALL POWER SAVE START @0 Reduction ( ) key (p. 15) NOTE: 11" x 17" sized copies are counted as Selects one of four preset reduction copy ratios: two copies. 50%, 64%, 77%, or 95%. #0 Clear ( ) key @1 Enlargement (...

  • Page 36: User Programs

    USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. List of user programs This copier has the following user programs. Program No. Program name Description Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.
  • Page 37 USER PROGRAMS Setting the user programs Press and hold the TRAY SELECT key for more than 5 seconds until all the alarm indicators* blink and “– –” appears in the copy quantity display. * The alarm indicators are the indicators. TRAY SELECT Enter a program number using the 10-key pad.
  • Page 38 USER PROGRAMS Select the desired parameter using the 10-key pad. The entered parameter number will blink on the right side of the copy quantity display. The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to “30 min.”, press key 2.

  • Page 39: Auditing Programs

    AUDITING PROGRAMS The auditing programs are used to set the internal auditor functions. Program No. Program name Description Auditing mode Enables or disables the auditing mode, which controls access to copier. See page 8. Account number Registers accounts for auditing mode. entry Account number Changes account numbers for auditing mode.
  • Page 40 AUDITING PROGRAMS Enter the number 16 using the 10-key pad and press the POWER SAVE START key. START Choose a new 3-digit code number and enter it using the 10-key pad. LECT Press the START key. START The code number will change from the previous setting to the new setting.
  • Page 41 AUDITING PROGRAMS Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 49, 3-digit account numbers can be assigned. Use program No. 11 to register account numbers.
  • Page 42 AUDITING PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. If no account number has been registered, “2E” will appear in the copy quantity display for approximately 5 seconds.
  • Page 43 AUDITING PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. 1.
  • Page 44 AUDITING PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual accounts. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. 1.

  • Page 45: Power Save Modes

    NOTE: As an ® Partner, SHARP NERGY The preheat mode and the auto power shut-off mode, which are has determined that this product meets controlled by the auto power save control function, will meet the ®...
  • Page 46 POWER SAVE MODES Setting the power save modes The factory default settings for the power save modes are OFF for the auto power save control function and ON for the preheat and auto power shut-off modes. The auto power save control function can be enabled or disabled as desired using user program No.

  • Page 47: User Maintenance

    USER MAINTENANCE The document glass and document cover must be kept clean to avoid dirty areas from being copied onto the copies. Document glass and document cover Wipe the document glass and document cover with a soft, clean cloth. If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.

  • Page 48: Copier Trouble

    Copies are too dark or too light. Are the indicator and the Contact your Sharp Service Center as copy quantity display blinking? soon as possible. See page 28. Is the original placed face down Place the original face down on the Blank copies.

  • Page 49: Copier Trouble

    Dust, dirt, smudges appear on copies. Developer is required. Contact your Is the indicator on? Sharp Service Center as soon as possible. See page 28. Maintenance is required. Contact your Is the indicator on? Sharp Service Center as soon as possible.
  • Page 50 An alphanumeric code will appear in the copy quantity display. Example Should the copier stop completely, and an alphanumeric code appear, contact your authorized Sharp Service Center.

  • Page 51: Supplies

    SUPPLIES Types and sizes of copy paper ORDINARY PAPER Automatic feeding from the paper trays or Manual feed tray (single sheet feed) manual feed tray (max. 50 sheets) 11" x 17" 11" x 17" Size: Size: 5-1/2" x 8-1/2" 5-1/2" x 8-1/2" 14 lbs.

  • Page 52: Genuine Supplies Statement

    SUPPLIES Genuine supplies statement For best copying results, be sure to use only Standard SF-2530 supplies replaced by the user include copy paper, toner, toner collecting container, and staple cartridges Sharp products. The package of Sharp toner has the Gunuine for an optional staple sorter.

  • Page 53: Specifications

    SPECIFICATIONS COPIER Type Desktop Copy system Dry, electrostatic transfer system Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17", min. 5-1/2" x 8-1/2" Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Copying speed 30 copies/min.
  • Page 54 SPECIFICATIONS Overall dimensions 47-29/64" (W) x 25-19/32" (D) (1205 mm (W) x 650 mm (D)) Weight (with Approx. 142.0 lbs. (64.4 kg) optional document Approx. 152.1 lbs. (69.0 kg) (with 500-sheet paper drawer) cover SF-CV13) Approx. 157.2 lbs. (71.3 kg) (with duplex module) Copier dimensions 24-59/64"...

  • Page 55: Optional Equipment

    ADF (SF-A17)/RADF (SF-A56) OPTIONAL EQUIPMENT CONTENTS Page SYSTEM CONFIGURATION ........ 54 AUTOMATIC DOCUMENT FEEDER (SF-A17)/ / / / / REVERSING AUTOMATIC DOCUMENT FEEDER (SF-A56) ..55 Part names ........... 55 Specifications ......... 55 Using the ADF or RADF ........56 Misfeed removal ........

  • Page 56: System Configuration

    ADF (SF-A17)/RADF (SF-A56) SYSTEM CONFIGURATION The options which are available for the SF-2530 are shown below. 10-bin sorter (SF-S18) Automatic document feeder (SF-A17) Reversing automatic document feeder (SF-A56) 20-bin sorter (SF-S15) Document cover (SF-CV13) Cassette (SF-IC11) 10-bin staple sorter (SF-S54N)

  • Page 57: Automatic Document Feeder (Sf-A17)

    ADF (SF-A17)/RADF (SF-A56) AUTOMATIC DOCUMENT FEEDER ( SF-A17 ) REVERSING AUTOMATIC DOCUMENT FEEDER ( SF-A56 ) An automatic document feeder (ADF) and reversing automatic document feeder (RADF) will handle 5-1/2" x 8-1/2" to 11" x 17" originals. If an RADF is installed, two-sided originals can be copied automatically without having to manually turn them over.

  • Page 58: Using The Adf Or Radf

    ADF (SF-A17)/RADF (SF-A56) Using the ADF or RADF Before loading originals into the document feeder Special originals such as transparency film and tray, be sure to remove any staples or paper clips tracing paper should not be fed from the ADF and from them.
  • Page 59 ADF (SF-A17)/RADF (SF-A56) Ensure that the 1-sided to 1-sided copying mode is SORTER ORIGINAL TO COPY EXPOSURE selected in the ORIGINAL TO COPY section of the AUTO (ORIGINALS) operation panel. MANUAL SORT EVEN NUMBER PHOTO ODD NUMBER When no indicator in the ORIGINAL TO COPY section is lit, the 1-sided to 1-sided copying mode is selected.
  • Page 60 ADF (SF-A17)/RADF (SF-A56) Enter the desired number of copies. The maximum number of copies in the two-sided copy mode is INTERRUPT 50 for 8-1/2" x 11" and 8-1/2" x 11"R and 30 for 8-1/2" x 14" and CLEAR ALL 11" x 17" paper. If the specified number of copies exceeds the above number, the copy quantity display will display the maximum allowable number after copying starts.
  • Page 61 ADF (SF-A17)/RADF (SF-A56) Enter the desired number of copies. POWER SAVE The maximum number of copies in the two-sided copy mode is 50 for 8-1/2" x 11" and 8-1/2" x 11"R and 30 for 8-1/2" x 14" and START 11" x 17" paper. If the specified number of copies exceeds the above number, the copy quantity display will display the maximum allowable number after copying starts.

  • Page 62: Misfeed Removal

    ADF (SF-A17)/RADF (SF-A56) Misfeed removal An original misfeed may occur at one of three locations: (A) in the feed section, (B) in the exit roller, or (C) under the transport belt. Location A (A) Open the feeding roller cover and pull the original gently Feeding roller cover to the right and out from the document feeder tray.

  • Page 63: 10-Bin Sorter (Sf-S18)

    10-BIN SORTER ( SF-S18 ) 20-BIN SORTER ( SF-S15 ) There are two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of originals and the second groups copies from different originals into separate sort bins. The maximum allowable number of copies varies with the selected mode.

  • Page 64: Using A Sorter

    10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15) Using a sorter Press the SORTER key to select the desired mode. SORT GROUP (The STAPLE SORT mode cannot be selected for either the SF-S18 or SF-S15.) To cancel the mode, press the SORTER key until the SORT and GROUP indicators go out.

  • Page 65: Sorter Capacities

    10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15) SORTER CAPACITIES SF-S18 SF-S15 Top bin Top bin 100 sheets in the NON-SORT mode 100 sheets in the NON-SORT mode Sort bins SORT mode: Sort bins: Bin capacity Paper size Up to 50 per bin in the SORT mode ( max.

  • Page 66: Misfeed Removal

    10-BIN SORTER (SF-S18) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. SF-S18 10-bin sorter Pull the sorter lock lever and carefully slide the sorter away from the copier.
  • Page 67 20-BIN SORTER (SF-S15) SF-S15 20-bin sorter Open the top cover and remove the misfed paper. Close the top cover. Confirm that the indicator has gone out. If the indicator is still blinking or the misfed paper cannot be seen from the top, slide the sorter carefully away from the copier.

  • Page 68: Specifications

    10-BIN SORTER (SF-S18)/ 20-BIN SORTER (SF-S15) Specifications SF-S18 No. of bins Bin capacity NON-SORT: 100 sheets (top bin) SORT: 30 sheets (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R) 15 sheets (8-1/2" x 14", 11" x 17", GROUP: 20 sheets (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2"...

  • Page 69: 10-Bin Staple Sorter (Sf-S54N)

    10-BIN STAPLE SORTER ( SF-S54N ) 20-BIN STAPLE SORTER ( SF-S56 ) There are two sorter modes for different copying jobs: NOTES: one sorts copies into sets matching the sequence of the To install the 20-bin staple sorter (SF-S56), an originals and the second groups copies from different optional stand/500-sheet paper drawer (SF-D20), originals into separate sort bins.

  • Page 70: Using A Sorter

    10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56) Using a sorter Press the SORTER key to select the desired mode. SORT GROUP To cancel the mode, press the SORTER key until the SORT, STAPLE SORT, and GROUP indicators all go out. (ORIGINALS) SORT EVEN NUMBE...

  • Page 71: Sorter Capacities

    10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56) SORTER CAPACITIES SF-S54N SF-S56 Top bin Top bin 100 sheets in the NON-SORT mode 100 sheets in the NON-SORT mode (60 sheets for 8-1/2" x 14" and 11" x 17") Sort bins Sort bins SORT mode: SORT or...

  • Page 72: Staple Sort

    10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56) Staple sort The STAPLE SORT mode staples copies of 5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17" sizes (SF-S54N) or copies of 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", and 11" x 17" sizes (SF-S56).
  • Page 73 10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56) Using the ADF or RADF Set the originals in the document feeder tray face up with the stapling position in the upper left corner. Stapling location SF-S54N If the number of copies to be delivered into each bin is more than 30 for 5-1/2"...

  • Page 74: Manual Stapling (Sf-S56 Only)

    20-BIN STAPLE SORTER (SF-S56) Manual stapling (SF-S56 only) To use the stapling feature only, without using the STAPLE SORT mode, follow the procedure below. Align the edges of the copies to be stapled. Place the set of copies into the top bin, making sure the Copies edges are flush with the inner right corner, as shown in the figure.

  • Page 75: Staple Cartridge Replacement

    10-BIN STAPLE SORTER (SF-S54N) Staple cartridge replacement The CHECK STAPLER indicator will blink when the staple cartridge is empty and the copier is in the STAPLE SORT mode. Replace the staple cartridge as follows. If there are still many staples left, then staples have jammed in the stapler.
  • Page 76 20-BIN STAPLE SORTER (SF-S56) SF-S56 20-bin staple sorter Open the stapler cover. Lift the release lever and pull out the staple box. Lift the release lever to unlock the staple box. Then pull out the box. Remove the empty staple cartridge from inside the staple box.
  • Page 77 If it is not stapled, press the manual staple key again. If the stapler does not operate properly even after replacement, a staple may be jammed in it. See page 77. Staples for the staple sorter are available from your Sharp dealer.

  • Page 78: Staple Jam Removal

    10-BIN STAPLE SORTER (SF-S54N) Staple jam removal If staples become jammed in the stapler, the CHECK STAPLER indicator and the STAPLE SORT mode indicator will blink. Remove the jammed staples in the manner described below. SF-S54N 10-bin staple sorter Open the stapler cover. Close the stapler cover.
  • Page 79 20-BIN STAPLE SORTER (SF-S56) SF-S56 20-bin staple sorter Open the stapler cover. Lift the release lever and pull out the staple box. Lift the release lever to unlock the staple box. Then pull out the box. Lower the lever at the end of the staple box and remove the jammed staples.
  • Page 80 20-BIN STAPLE SORTER (SF-S56) Insert the staple box into the stapler unit until it clicks in place. Close the stapler cover. Following the stapling procedure on page 72, staple a copy to check that the stapler works properly. If it does not, repeat this procedure until it does.

  • Page 81: Misfeed Removal

    10-BIN STAPLE SORTER (SF-S54N) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. SF-S54N 10-bin staple sorter Pull the sorter lock lever and carefully slide the staple sorter away from the copier.
  • Page 82 20-BIN STAPLE SORTER (SF-S56) SF-S56 20-bin staple sorter Push the sorter release button and slide the sorter carefully along the guides away from the copier. Remove the misfed paper from the sorter or from the exit area of the copier. Slide the sorter back toward the copier and latch it into place.

  • Page 83: Specifications

    10-BIN STAPLE SORTER (SF-S54N)/ 20-BIN STAPLE SORTER (SF-S56) Specifications SF-S54N No. of bins Bin capacity NON-SORT: 100 sheets (top bin) SORT/ 30 sheets (5-1/2" x 8-1/2", 8-1/2" x 11", STAPLE 8-1/2" x 11"R) SORT: 15 sheets (8-1/2" x 14", 11" x 17") GROUP: 20 sheets (5-1/2"...

  • Page 84: Stand/500-Sheet Paper Drawer (Sf-D20)

    STAND/500-SHEET PAPER DRAWER (SF-D20) STAND/1000-SHEET PAPER DRAWER (SF-D21) These optional stands with paper trays provide the convenience of increased paper capacity for the copier and make a choice of paper sizes readily available for copying. Even greater paper capacity and size flexibility are available when the stands are equipped with an optional auxiliary 500-sheet paper drawer (SF-CM11).

  • Page 85: Loading Copy Paper

    STAND/500-SHEET PAPER DRAWER (SF-D20)/STAND/1000-SHEET PAPER DRAWER (SF-D21) Loading copy paper The size of the copy paper for the paper tray will be set by Sharp service personnel according to your request when you purchase the copier. If a different paper size setting is required, contact your authorized Sharp Service Center.

  • Page 86: Misfeed Removal

    STAND/500-SHEET PAPER DRAWER (SF-D20)/STAND/1000-SHEET PAPER DRAWER (SF-D21) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. Open the side cover and remove any misfed paper. Be sure to perform this step before pulling out either of the paper drawers.

  • Page 87: Specifications

    STAND/500-SHEET PAPER DRAWER (SF-D20)/STAND/1000-SHEET PAPER DRAWER (SF-D21) Specifications SF-D20 Paper size 8-1/2" x 11" to 11" x 17" Paper capacity 500 sheets of 20 lb. bond paper Total of 1,000 sheets of 20 lb. bond paper with an optional 500-sheet paper drawer installed Weight Approx.
  • Page 88 MEMO...

  • Page 89: Auditor Code Number: Factory Setting

    AUDITOR CODE NUMBER: FACTORY SETTING The following is the factory setting of the Auditor Code Number, which must be used to access the Auditing Programs. Factory setting = 000 This number must be entered when accessing the Auditing Programs for the first time. (See page 37.) NOTE: The Auditor Code Number is an important security number allowing the auditing manager to configure the auditor’s...
  • Page 90 DSC3 CINSE1807FC51...
  • Page 91 Sharp. You should be aware, however, that Sharp does not itself extend any warranties, either express or implied, directly to you, the end-user and no one is authorized to make any representations or warranties on behalf of Sharp.
  • Page 92 SF-2530 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. SHARP CORPORATION PRINTED IN HONG KONG TINSE1807FCZZ...

Table of Contents