Korg microARRANGER Owner's Manual page 205

c: Envelope Select, c: Src, d: Threshold
These parameters select the source to control the start and
end of recording.
When "Envelope Select" is set to D-mod, the input signal will
be recorded only when the value of the modulation source
selected by the Src parameter is 64 or higher.
When "Envelope Select" is set to Input, the input signal will
be recorded only when its level exceeds the Threshold level.
When recording is completed, reverse playback starts imme-
diately.
043: L/C/R Delay
This multitap delay outputs three Tap signals to the
left, right, and center respectively. You can also adjust
the left and right spread of the delay sound.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
L Delay Time [msec]
Sets the delay time of TapL
a
Level
Sets the output level of TapL
C Delay Time [msec]
Sets the delay time of TapC
b
Level
Sets the output level of TapC
R Delay Time [msec]
Sets the delay time of TapR
c
Level
Sets the output level of TapR
Feedback (C Delay)
Sets the feedback amountof TapC
Src
d
Selects the modulation source of the TapC feedback amount
Amt
Sets the modulation amount of the TapC feedback amount
High Damp [%]
Sets the damping amount in the high range
e
Low Damp [%]
Sets the damping amount in the low range
Input Level Dmod [%]
Sets the modulation amount of the input level
f
Src
Selects the modulation source for the input level
Spread
g
Sets the width of the stereo image of the effect sound
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
h
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
Wet / Dry
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
Wet / Dry
0...1360msec
0...50
0...1360msec
0...50
0...1360msec
0...50
–100...+100
Off...Tempo
–100...+100
0...100%
0...100%
–100...+100
Fx:037,
Off...Tempo
Fx:037
0...50
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
e: High Damp [%], e: Low Damp [%]
These parameters set the damping amount of high range and
low range. The tone of the delayed sound becomes darker
and lighter as it feeds back.
g: Spread
This parameter sets the pan width of the effect sound. The
stereo image is widest with a value of 50, and the effect
sound of both channels is output from the center with a value
of 0.
044: Cross Delay
(Stereo/Cross Delay)
This is a stereo delay, and can by used as a cross‐feed‐
back delay effect in which the delay sounds cross over
between the left and right by changing the feedback
routing.
Stereo In - Stereo Out
Left
Input Level D-mod
Stereo/Cross
Input Level D-mod
Right
Stereo/Cross
a
Switches between stereo delay and cross-feedback delay
L Delay Time [msec]
b
Sets the delay time for the left channel
R Delay Time [msec]
c
Sets the delay time for the right channel
L Feedback
Sets the feedback amount for the left channel
Src
d
Selects the modulation source of feedback amount
Amt L
Sets the modulation amount of the left channel feedback
R Feedback
Sets the feedback amount for the right channel
e
Amt R
Sets the modulation amount of the right channel feedback
High Damp [%]
f
Sets the damping amount in the high range

Low Damp [%]
g
Sets the damping amount in the low range

Input Level Dmod [%]
Sets the modulation amount of the input level
h
Src
Selects the modulation source for the input level
Spread
i
Sets the width of the stereo image of the effect sound

Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
j
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
Effects
ER/Delay

High Damp Low Damp
Delay
Feedback
Spread
High Damp Low Damp
Delay
Stereo/Cross
Stereo, Cross
0.0...680.0msec
0.0...680.0msec
Fx:037,
Dry, 1:99...99:1, Wet
203
Wet / Dry
Wet / Dry
–100...+100
Off...Tempo
–100...+100
–100...+100
–100...+100
0...100%
Fx:043
0...100%
Fx:043
–100...+100
Off...Tempo
Fx:037
–50...+50
Fx:043
Off...Tempo
–100...+100