Korg microARRANGER Owner's Manual page 118

116 Program operating mode
Page 11 - Filter EG
Attack Time
This parameter specifies the time over which the level
will change from note‐on until the attack level is reached.
Decay Time
This parameter specifies the time over which the level
will change from the attack level to the break point level.
Slope Time
This parameter specifies the time over which the level
will change after the decay time has elapsed until the
sustain level is reached.
Release Time
This parameter specifies the time over which the level
will change after note‐on occurs until the release level
is reached.
Filter EG 'Level' modulation
Filter 1 EG changes (level) (AMS = Velocity, Intensity = a positive (+) value)
Note-on Note-on
Note-off
Softly played note with Start Strongly played note with Start
Level Swing, Attack Level Swing, Level Swing, Attack Level Swing,
and Break Level Swing set to + and Break Level Swing set to +
AMS(L) (Alternate Modulation Source)
This parameter selects the source that will control the
"Level" parameters of the filter EG ("AMS (Alternate
Modulation Source) list" on page 123).
Intensity (AMS Intensity)
This parameter specifies the depth and direction of the
effect applied by "AMS". With a setting of 0, the levels spec‐
ified by "Frequency A (Cutoff Frequency A)" will be used.
For example, if "AMS" is Velocity, and you set "Start
Level Swing", "Attack Level Swing" and "Break Level
Swing" to + and set "Intensity" to a positive (+) value,
the EG levels will rise as you play more strongly. If
"Intensity" is set to a negative (–) values, the EG levels
will fall as you play more strongly.
‐99...+99 Intensity value.
Start Level Swing
This parameter specifies the direction in which "AMS"
will affect "Start Level". When "Intensity" has a posi‐
tive (+) value, a setting of + for this parameter will
allow "AMS" to raise the EG level, and a setting of –
will allow "AMS" to lower the EG level. With a setting
of 0 there will be no change.
Attack Level Swing
This parameter specifies the direction in which "AMS"
will affect "Attack Level". When "Intensity" has a posi‐
tive (+) value, a setting of + for this parameter will
allow "AMS" to raise the EG level, and a setting of –
will allow "AMS" to lower the EG level. With a setting
of 0 there will be no change.
Break Level Swing
This parameter specifies the direction in which "AMS"
will affect "Break Point Level". When "Intensity" has a
positive (+) value, a setting of + for this parameter will
allow "AMS" to raise the EG level, and a setting of –
will allow "AMS" to lower the EG level. With a setting
of 0 there will be no change.
Note-on
Note-off Note-off
Strongly played note with Start
Level Swing, Attack Level Swing,
and Break Level Swing set to –
Filter EG 'Time' modulation
Filter 1 EG changes (Time) (AMS = Velocity, Intensity = a positive (+) value)
Note-on Note-on
Note-off
Softly played note with Attack, Strongly played note with
Decay, Slope and Release Attack, Decay, Slope and
Level Swings set to + Release Level Swings set to +
AMS1/2(T)
Use this parameter to select the source that will control
the "Time" parameters of the filter EG. See "AMS
(Alternate Modulation Source) list" on page 123.
Intensity
This parameter specifies the depth and direction of the
effect that "AMS1/2(T)" will have.
For example, if "AMS1/2(T)" is set to FltKTr +/+, the EG
"Time" parameters will be controlled by the Keyboard
Tracking settings. With positive (+) values of this
parameter, positive (+) values of "Ramp" will lengthen
the EG times, and negative (–) values of "Ramp" will
shorten the EG times. The direction of change is speci‐
fied by "Attack Time Swing", "Decay Time Swing",
"Slope Time Swing", and "Release Time Swing".
With a setting of 0, the times specified by "Frequency A
(Cutoff Frequency A)" will be used.
If "AMS1/2(T)" is set to Velocity, positive (+) values of
this parameter will cause EG times to lengthen as you
play more strongly, and negative (–) values will cause
EG times to shorten as you play more strongly.
‐99...+99 Intensity value.
Attack Time Swing
This parameter specifies the direction in which "AMS1/
2(T)" will affect the attack time. With positive (+) values
of "Intensity", setting this parameter to + will allow
AMS to lengthen the time, and setting this parameter to
– will allow AMS to shorten the time. With a setting of
0 there will be no change.
Decay Time Swing
This parameter specifies the direction in which "AMS1/
2(T)" will affect the decay time. With positive (+) values
of "Intensity", setting this parameter to + will allow
AMS to lengthen the time, and setting this parameter to
– will allow AMS to shorten the time. With a setting of
0 there will be no change.
Slope Time Swing
This parameter specifies the direction in which "AMS1/
2(T)" will affect the slope time. With positive (+) values
of "Intensity", setting this parameter to + will allow
AMS to lengthen the time, and setting this parameter to
– will allow AMS to shorten the time. With a setting of
0 there will be no change.
Release Time Swing
This parameter specifies the direction in which "AMS1/
2(T)" will affect the release time. With positive (+) val‐
ues of "Intensity", setting this parameter to + will allow
AMS to lengthen the time, and setting this parameter to
– will allow AMS to shorten the time. With a setting of
0 there will be no change.
Note-on
Note-off Note-off
Strongly played note with
Attack, Decay, Slope and
Release Level Swings set to –