Korg microARRANGER Owner's Manual page 195

When "Control Mode" = LFO, the intensity of resonance var-
ies according to the LFO. The LFO sways between positive
and negative values, causing resonance to occur between
specified pitches an octave apart in turn.
When "Control Mode" = D-mod, the resonance is controlled
by the dynamic modulation source. If JS X or Ribbon is
assigned as the modulation source, the pitch an octave
higher and lower can be controlled, similar to when LFO is
selected for Control Mode.
a: LFO/D-mod Invert
When "Control Mode" = LFO or D-mod, the controlled phase
of either Voice 1 or 2 will be reversed. When the resonance
pitch is set for Voice 1 (Resonance has a positive value),
Voice 2 will resonate at a pitch an octave below (Resonance
has a negative value).
d: Voice1: Pitch, d: Fine [cent], g: Voice2: Pitch, g: Fine
[cent]
The Pitch parameter specifies the pitch of resonance by note
name. The "Fine" parameter allows for fine adjustment in
steps of cents.
e: High Damp [%], h: High Damp [%]
This parameter sets the damping amount of resonant sound
in the high range. Lower values will make a metallic sound
with a higher range of harmonics.
030: Doppler
This effect simulates the "Doppler effect" of a moving
sound with a changing pitch, similar to the siren of an
passing ambulance. Mixing the effect sound with the
dry sound will create a unique chorus effect.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Doppler
Right
LFO
D
-mod
Trigger LFO Mode = 1-Shot
LFO Mode
Switches LFO operation mode
a
Src
When LFO Mode is set to 1-Shot, this modulation source triggers the LFO
LFO Sync
b
Switches between LFO reset on and off when LFO Mode is set to Loop
LFO Frequency [Hz]
Sets the LFO speed
Src
c
Selects the modulation source of LFO speed
Amt
Sets the modulation amount of LFO speed
BPM/MIDI Sync
Switches between using the frequency of the LFO speed and using the
tempo and notes
BPM
Selects MIDI Clock and assigns tempo
d
Base Note
Selects the type of notes that specify the LFO speed
Times
Sets the number of notes that specify the LFO speed
e
f
g
a: LFO Mode, a: Src, b: LFO Sync
The "LFO Mode" parameter switches LFO operation mode.
When Loop is selected, the Doppler effect will be created
repeatedly. If "LFO Sync" is set to On, the LFO will be reset
when the modulation source specified with the "Src" parame-
ter is turned on.
When "LFO Mode" is set to 1-Shot, the Doppler effect is cre-
ated only once when the modulation source specified in the
"Src" field is turned on. At this time if you do not set the "Src"
parameter, the Doppler effect will not be created, and no
effect sound will be output.
Wet / Dry
e: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
Pan Depth
approaches, and the pitch is lowered when the sound goes
away. This parameter sets this pitch variation.
f: Pan Depth
Wet / Dry
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go
from much further away. With positive values, the sound
moves from left to right; with negative values, the sound
Loop, 1-Shot
,
moves from right to left.
Off...Tempo

Off, On

0.02...20.00Hz
Fx:009,
Off...Tempo
–20.00...+20.00Hz
Off, On
Fx:009,
MIDI, 40...240
Fx:009
Fx:009
x1...x16
Fx:009
Pitch Depth
Sets the pitch variation of the moving sound
Src
Selects the modulation source of pitch variation
Amt
Sets the modulation amount of pitch variation
Pan Depth
Sets the panning of the moving sound
Src
Selects the modulation source of panning
Amt
Sets the modulation amount of panning
Wet/Dry
Table , "Sets the balance between the effect and dry sounds," on page 175
Src
Table , "Selects the modulation source of the effect balance," on page 175
Amt
Table , "Sets the modulation amount of the effect bal-
ance," on page 175
The effect is off when a value for the modulation source specified for
the "Src" parameter is smaller than 64, and the effect is on when the
value is 64 or higher. The Doppler effect is triggered when the value
changes from 63 or smaller to 64 or higher.
Pitch
Pan Depth
= (+) value
Original Pitch
Center
Left
Pan Depth
< < < < < <<<<<< >>>>>> > >
Louder Volume
Effects 193
Pitch/Phase Mod.
0...100
,
Off...Tempo
–100...+100
–100...+100
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Doppler - Pitch / Pan Depth
Pan Depth
= (–) value
Pitch Depth
Right
> > >
Louder