Mechanical Section (With Regard To The Sewing Machine); Specifications - JUKI AMS-210EN/IP-420 Instruction Manual

!. MECHANICAL SECTION (WITH REGARD TO THE SEWING MACHINE)

1. SPECIFICATIONS

 Sewing area
2 Max. sewing speed
3 Stitch length
4 Feed motion of feeding frame
5 Needle bar stroke
6 Needle
7 Lift of feeding frame
8 Intermediate presser stroke
9 Lift of intermediate
presser
0 Intermediate presser
DOWN position
variable
 Shuttle
2 Lubricating oil
3 Memory of pattern
data
4 Temporary stop facility
5 Enlarging / Reducing
facility
6 Enlarging / Reducing
method
7 Max. sewing speed
limitation
8 Pattern selection
facility
9 Bobbin thread counter
20 Sewing counter
2 Memory back-up
22 2nd origin setting
facility
23 Sewing machine motor
24 Dimensions
25 Mass (gross mass)
26 Power consumption
27 Operating temperature
range
28 Operating humidity range
29 Line voltage
30 Air pressure used
3 Air consumption
32 Needle highest
position stop facility
33 Noise
"sti/min" is an abbreviation for "stitches per minute."
※1
X (lateral) direction
AMS-20EN-306 :
AMS-20EN-50 :
AMS-20EN-220 :
2,800 sti/min (When sewing pitch is 4 mm or less)
0. to 2.7 mm (Min. resolution : 0.05 mm)
Intermittent feed (2-shaft drive by stepping motor)
4.2 mm
GROZ-BECKERT 34, 35x7, ORGAN needle DPx5, DPx7
Max. 25mm (Pneumatic type only Max.30mm)
4 mm (Standard) (0 to 0 mm)
20 mm
Standard 0 to 3.5 mm (Max. 0 to 7.0 mm)
Double-capacity semi-rotary hook
New Defrix Oil No. 2 (Supplied by oiler)
Main body, Media
• Main body : Max. 999 patterns (Max. 50,000 stitches/pattern)
• Media : Max. 999 patterns (Max. 50,000 stitches/pattern)
Used to stop machine operation during a stitching cycle.
Allows a pattern to be enlarged or reduced on the X axis and Y axis independently
when sewing a pattern. Scale : % to 400% times (0.% steps)
Pattern enlargement / reduction can be done by increasing / decreasing either stitch
length or the number of stitches. (Increasing/decreasing stitch length only can be
performed when pattern button is selected.)
200 to 2,800 sti/min (Scale : 00 sti/min steps)
Pattern No. selection method
(Main body :  to 999, Media :  to 999)
UP/DOWN method (0 to 9,999)
UP/DOWN method (0 to 9,999)
In case of a power interruption, the pattern being used will automatically be stored in
memory.
Using jog keys, a 2nd origin (needle position after a sewing cycle) can be set in the
desired position within the sewing area. The set 2nd origin is also stored in memory.
Servo-motor
,200mm (W) x 70mm (L) x ,200mm (H) (Excluding thread stand)
Machine head 69kg, control box 6.5kg
450 VA
5˚C to 35˚C
35 % to 85 % (No dew condensation)
Rated voltage ±0% 50 / 60 Hz
Standard 0.35 to 0.4 MPa (Max. 0.55 MPa)(Pneumatic type only)
.8 dm / min (ANR) (Pneumatic type only)
3
After the completion of sewing, the needle can be brought up to its highest position.
- Equivalent continuous emission sound pressure level (L
A-weighted value of 82 dB; (Includes L
-ISO 204 GR2 at 2,800 sti/min
- Sound power level (L
WA
A-weighted value of 9 dB; (Includes K
-ISO 204 GR2 at 2,800 sti/min
Time required for sewing: 2.2 sec, using Pattern No. 02
–  –
30 mm ×
50 mm ×
220 mm ×
= 2.5 dB); according to ISO 082- C.6.3
pA
※1
.
) ;
= 2.5 dB); according to ISO 082- C.6.3
WA
※1 .
Y (longitudinal) direction
60 mm
00 mm
00 mm
) at the workstation :
pA