Table of Contents
Advertisement
TMS320F2809, TMS320F2808, TMS320F2806
TMS320F2802, TMS320F2801, TMS320C2802
TMS320C2801, TMS320F28016, TMS320F28015
SPRS230N – OCTOBER 2003 – REVISED MAY 2012
3.2.17 Peripheral Frames 0, 1, 2 (PFn)
The 280x segregate peripherals into three sections. The mapping of peripherals is as follows:
PF0:
PIE:
Flash:
Timers:
CSM:
ADC:
PF1:
eCAN:
GPIO:
ePWM:
eCAP:
eQEP:
PF2:
SYS:
SCI:
SPI:
ADC:
I2C:
3.2.18 General-Purpose Input/Output (GPIO) Multiplexer
Most of the peripheral signals are multiplexed with general-purpose input/output (GPIO) signals. This
enables the user to use a pin as GPIO if the peripheral signal or function is not used. On reset, GPIO pins
are configured as inputs. The user can individually program each pin for GPIO mode or peripheral signal
mode. For specific inputs, the user can also select the number of input qualification cycles. This is to filter
unwanted noise glitches. The GPIO signals can also be used to bring the device out of specific low-power
modes.
3.2.19 32-Bit CPU-Timers (0, 1, 2)
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock
prescaling. The timers have a 32-bit count-down register, which generates an interrupt when the counter
reaches zero. The counter is decremented at the CPU clock speed divided by the prescale value setting.
When the counter reaches zero, it is automatically reloaded with a 32-bit period value. CPU-Timer 2 is
reserved for the DSP/BIOS Real-Time OS, and is connected to INT14 of the CPU. If DSP/BIOS is not
being used, CPU-Timer 2 is available for general use. CPU-Timer 1 is for general use and can be
connected to INT13 of the CPU. CPU-Timer 0 is also for general use and is connected to the PIE block.
3.2.20 Control Peripherals
The 280x devices support the following peripherals which are used for embedded control and
communication:
ePWM:
eCAP:
38
Functional Overview
Product Folder Link(s):
PIE Interrupt Enable and Control Registers Plus PIE Vector Table
Flash Control, Programming, Erase, Verify Registers
CPU-Timers 0, 1, 2 Registers
Code Security Module KEY Registers
ADC Result Registers (dual-mapped)
eCAN Mailbox and Control Registers
GPIO MUX Configuration and Control Registers
Enhanced Pulse Width Modulator Module and Registers
Enhanced Capture Module and Registers
Enhanced Quadrature Encoder Pulse Module and Registers
System Control Registers
Serial Communications Interface (SCI) Control and RX/TX Registers
Serial Port Interface (SPI) Control and RX/TX Registers
ADC Status, Control, and Result Register
Inter-Integrated Circuit Module and Registers
The enhanced PWM peripheral supports independent/complementary PWM
generation, adjustable dead-band generation for leading/trailing edges,
latched/cycle-by-cycle trip mechanism. Some of the PWM pins support HRPWM
features.
The enhanced capture peripheral uses a 32-bit time base and registers up to four
programmable events in continuous/one-shot capture modes.
This peripheral can also be configured to generate an auxiliary PWM signal.
Submit Documentation Feedback
TMS320F2809 TMS320F2808 TMS320F2806 TMS320F2802 TMS320F2801 TMS320C2802
TMS320C2801 TMS320F28016 TMS320F28015
Copyright © 2003–2012, Texas Instruments Incorporated
www.ti.com
Advertisement
Table of Contents
