IBM 436854u - System x3200 M2 5U Mini Tower Server Problem Determination And Service Manual page 6

Removing and replacing Tier 2 CRUs
Removing and replacing FRUs
Chapter 5. Diagnostics . . . . . . . . . . . . . . . . . . . . . 121
Diagnostic tools . . . . . . . . . . . . . . . . . . . . . . . . 121
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Checkout procedure . . . . . . . . . . . . . . . . . . . . . . 137
iv
System x3200 M2 Types 4367 and 4368: Problem Determination and Service Guide
Installing the lower bezel . . . . . . . . . . . . . . . . . . . . 55
Removing the upper bezel. . . . . . . . . . . . . . . . . . . . 56
Installing the upper bezel . . . . . . . . . . . . . . . . . . . . 57
Removing an adapter . . . . . . . . . . . . . . . . . . . . . 58
Installing an adapter . . . . . . . . . . . . . . . . . . . . . . 59
Removing and installing internal drives . . . . . . . . . . . . . . . 61
Removing a hot-swap power supply . . . . . . . . . . . . . . . . 72
Installing a hot-swap power supply
Removing a memory module . . . . . . . . . . . . . . . . . . . 75
Installing a memory module . . . . . . . . . . . . . . . . . . . 76
Removing the battery . . . . . . . . . . . . . . . . . . . . . 77
Installing the battery . . . . . . . . . . . . . . . . . . . . . . 77
Removing the rear system fan . . . . . . . . . . . . . . . . . . 79
Installing the rear system fan. . . . . . . . . . . . . . . . . . . 80
Removing the hard disk drive fan assembly . . . . . . . . . . . . . 81
Installing the hard disk drive fan assembly . . . . . . . . . . . . . . 83
Removing the simple-swap backplate
Installing the simple-swap backplate . . . . . . . . . . . . . . . . 86
Removing the SAS/SATA hard disk drive backplane . . . . . . . . . . 87
Installing the SAS/SATA hard disk drive backplane . . . . . . . . . . . 88
Removing the front-panel assembly . . . . . . . . . . . . . . . . 89
Installing the front-panel assembly . . . . . . . . . . . . . . . . . 90
Removing the front USB connector assembly. . . . . . . . . . . . . 90
Removing the rear adapter retention bracket . . . . . . . . . . . . . 91
Installing the rear adapter retention bracket . . . . . . . . . . . . . 92
Removing the front adapter-retention bracket . . . . . . . . . . . . . 92
Installing the front adapter-retention bracket . . . . . . . . . . . . . 93
Installing the front USB connector assembly . . . . . . . . . . . . . 93
Removing the hot-swap power supply cage . . . . . . . . . . . . . 94
Installing the hot-swap power supply cage . . . . . . . . . . . . . . 95
Removing the mini-SAS/SATA controller. . . . . . . . . . . . . . . 96
Installing the SAS/SATA controller . . . . . . . . . . . . . . . . . 97
Removing the optional mini-PCI-X enablement card . . . . . . . . . . 97
Installing the optional mini-PCI-X enablement card . . . . . . . . . . . 98
Removing the IBM ServeRAID-MR10i SAS/SATA controller
Installing the IBM ServeRAID-MR10i SAS/SATA controller
Removing an IBM Remote Supervisor Adapter II SlimLine
Installing an IBM Remote Supervisor Adapter II SlimLine . . . . . . . . 102
Removing a non-hot-swap power supply . . . . . . . . . . . . . . 105
Installing a non-hot-swap power supply . . . . . . . . . . . . . . 107
Removing the microprocessor and fan sink . . . . . . . . . . . . . 109
Installing a microprocessor and fan sink . . . . . . . . . . . . . . 111
Removing the system board
Installing the system board . . . . . . . . . . . . . . . . . . . 116
POST beep codes . . . . . . . . . . . . . . . . . . . . . . 122
No-beep symptoms . . . . . . . . . . . . . . . . . . . . . . 124
Error logs . . . . . . . . . . . . . . . . . . . . . . . . . 125
POST error codes . . . . . . . . . . . . . . . . . . . . . . 127
About the checkout procedure . . . . . . . . . . . . . . . . . . 137
. . . . . . . . . . . . . . . . 74
. . . . . . . . . . . . . . . . 77
. . . . . . . . . . . . . . . 84
. . . . . . . . . . . . . . . . . . 105
. . . . . . . . . . . . . . . . . . 114
. . . . . . . 99
. . . . . . . 100
. . . . . . . 102