The Display; Function Keys; Creating Your First Label - Dymo RhinoPRO 1000 Instructions For Use

Introduction
The Dymo 1000 Electronic Labelmaker enables you to create a
wide variety of high quality self-adhesive labels of up to 100
characters.
The Labelmaker uses 12mm ( 1 / wide tape cassettes in a
2 ")
number of label colours.
Normal or double width, full and half-height text can be printed
in a single line, or in half-height on two lines.
Text can be set horizontally or
always centred on the label.

Function keys

ON/OFF
CLEAR TEXT
• Press to clear all the text and
Switches the power on and off.
the length setting, but leave the
• Switches off automatically after
print size and style settings
three minutes if no keys are
unchanged.
pressed. The last label created
will be stored and displayed
CURSOR KEYS
when next turned on.
These keys move the cursor
Note: If the batteries are removed
along the text.
for more than a few seconds, or the
external power supply interrupted,
• Pressing
all text and settings will be lost.
moves the cursor to the
When power is restored, the
beginning or end of the text.
display will show a flashing cursor
When used in conjunction with
(no text) and the settings will be full-
certain function keys, use
height, normal width, auto length,
to select options and
<
and off.
numerical values.
CAPS
• To insert characters into the text,
CAPITALS
CAPS
use
• Press for all subsequent
cursor under the character to the
characters in UPPER CASE
right of the insertion point, then
(CAPITALS), as confirmed by
type in the characters required.
the indicator in the top left
corner of the display.
PRINTING
• Press again to cancel and
return to lower case.
• Press
SHIFT KEY
• Press the cutter button to
release the label.
• Press and release before
pressing an alphabet key to
SPACE KEY
produce an UPPER CASE
character, as confirmed by the • Press
indicator in the lower left corner
space into the text.
of the display.
FEED
• For dual purpose keys, press
• Press to feed out 25mm of tape
first to produce the legend
without printing.
above the key.
• Pressing while is set,
CAPS SYMBOLS
will give lower case characters.
• Press to select a symbol
character – see 'Symbols and
DELETE
DEL
special characters'.
• Press to delete the character to
the left of the cursor, or to
cancel certain function key
operations.
4 DYMO 1000
TEXT SIZE
• Press to display the symbols
representing the four text print
sizes:
normal height and width
normal height, double width
half-height, normal width
half-height, double width.
The cursor will be positioned
over the current selection.
and is
• Press to cancel, or use
DEL
or to move the cursor
< <
over the size symbol required,
then press
SIZE
CLEAR
selection, or
+
DEL
size and print the label.
TWO-LINE TEXT
Labels comprising two lines of
text can be printed on the 12mm
< <
( 1 / ") wide labels.
2
• Press to insert the special
character
<<
< <
+ or +
< you want the text to break, eg:
<
This label has
on the display will print as:
or
<
This label has
two line text.
Only one
or to position the
< a label at a time.
<
• Press to delete
DEL
normal text characters.
Note: Two lines cannot be printed
PRINT
vertically.
PRINT VERTICAL TEXT
to print the label.
• Rotates the text through 90
so that the label is printed
confirmed by the indicator in the
top right of the display.
to insert a
• Press again to cancel and
return to horizontal text.
FEED
+
SYM
SIZE
LABEL LENGTH
Displays the current label length.
The length is normally calculated
automatically, according to the
length of the text on the label.
• Press
DEL
function without changing the
length, or:
• use or
<
400mm or 15" max.) or
decrease the length in 5mm
1
( / ") steps. The display will
5
flash if you try to make the label
to confirm the
shorter than the text.
• If the length displayed is
PRINT to fix the new
preceded by the > symbol, the
length has already been fixed;
the label is too short for the text
2-LINE
and it will not print. Either press
+
CAPS
to increase the length in
<
5mm ( 1 / ") steps until the >
5
symbol disappears, or press
CLEAR
+
DEL
length; the label is now long
at the point where
enough for the text and can be
printed.
two line text.
• Press
the length for all subsequent
labels as indicated in the lower
right corner of the display, or
PRINT
• press
length and print the label.
can be included in
• Pressing
the fixed length and restore the
automatic length.
, as for
INCREMENTAL
PRINTING
Prints a label then increments the
VERT
+ last digit of any number in the
SYM
label by 1, ready for the next print
command.
, as
• Press PRINT
label, or
next label and increment again
by 1.
LENGTH

The Display

+
SIZE
to cancel the length
to increase (up to
<
The display shows:
• Up to five text characters, plus the cursor, at one
time. Use
• Four indicators, one in each corner – as shown
above.
• The display will flash if you press an incorrect key in
a function sequence.
to cancel fixed
LENGTH
$
+ again to fix
SIZE
1
/
6
to fix the new
<<
CLEAR
+ will cancel
<
DEL
A
+
PRINT
G
M
S
Y
to print the next
+ to print the
PRINT

Creating your first label

• Fit batteries or connect the AC adaptor, and
insert a tape cassette.
• Press
• Type in your text using the alphabet keys; each
character will appear in the display. If you make a
mistake, press
in the correction.
• Press
button to release the label.
CAPS lock on Vertical text
12345
—
Shift on Fixed length on
CURSOR
or to move along the text.
< <
PRINT
Label cutter
button. Press to
release label.
- =
£ ' %
3 + NOTE:
2 4 5
Always remove
:
( )
*
' .
7 8 0
9 a cut label
before printing
another.
< <
2-LINE LENGTH VERT CLEAR
<
DEL
CAPS SIZE SYM
B C D E F
H I J K L
N O P Q R
X
T U V W
?
! i ?
..
Z
/ /
^
FEED
~
C ,
Œ
N
to switch on.
to delete the error, then type
DEL
PRINT to print the label, then press the cutter
DYMO 1000
5