Dymo RhinoPRO 1000 Instructions For Use

Symbols and special characters
International characters
You can create international characters by combining a letter
and a diacritical (accent). Diacriticals available on the keyboard
are ´ ` ¨ and ^. To add a diacritical to a character, enter the
character first, followed immediately by the diacritical. For
example, press 'E' followed by '´' to get é.
To add a diacritical to an existing character, use
place the cursor under the character to be changed, then press
the appropriate diacritical key.
Symbols
Pressing changes the display to show symbols and
SYM
special characters, some of which are not available direct from
the keyboard. The display will show:
a-o? (or a-r ? where available).
Each letter selects a line of five symbol characters, as shown in
the table below. Note that some of the more complex printed
symbols are represented by simpler symbols in the display.
Press to cancel or press the letter key required.
DEL
Use or to select a symbol. Press
<
<
PRINT
symbol in the label, or press to place it and print the label.
DISPLAYED
CHARACTERS
a $ ¢ £ F r ¥
b @ & # :
;
c
" < > =
d
\ X % *
e
R C T
M
f 2 3 1 /
2
2 3
g
. . . 3 . . . 4 . . . 5 . . .
. . .
h 1 2
. . .
i
6
j
Æ Å Ç Œ Ø
k æ å ç œ ø
l
Ã Ë Ñ Õ
m ã ë ñ õ
n â ê î ô û
o
ß ¿ ¡
Note: Rows
p
Á É Í Ó Ú
p, q and r
q
á é í ó ú
where
available.
r
ì ò !
Print contrast — may be adjusted by pressing
space key to display five contrast symbols. Use
symbol. Press again to confirm the setting. The contrast level will
SYM
revert to the mid-setting when the Labelmaker is turned off and on
again.
6
DYMO 1000

Troubleshooting

No display
• check machine is on
• replace discharged batteries
or use the AC adaptor
• check AC adaptor plugged
in and switched on.
No printing or poor text
or to
<
<
• replace discharged batteries
or use the AC adaptor
• check tape cassette
installed correctly and tape
not kinked
• replace the tape cassette.
No response to print key
• label length too short for text
– press until >
<
disappears or clear fixed
length
• !!!!! in display indicates a
printer jam. Printing will stop
again to place the
SYM
and the display return to
normal. Open the cassette
compartment and free the
jam.
PRINTED
• flashing in the display
CHARACTERS
indicates low battery volts.
$ ¢ £ F r ¥
Replace discharged
batteries or use the AC
@ & # : ;
adaptor.
" < > =
Accessories
\ X % *
® © ™
12mm ( 1 / ") cassettes
2
Black/Clear
2 3 1 /
2
Blue/Clear
2 3
Red/Clear
Black/White
Blue/White
!
Red/White
Black/Blue
Black/Red
Æ Å Ç Œ Ø
Black/Yellow
æ å ç œ ø
Black/Green
Replacement Cutter
Ã Ë Ñ Õ
Carrying Case
ã ë ñ õ
AC Adaptor
â ê î ô û
This product is designed to conform with the
following international standards:
ß ¿ ¡
EN 60950 Specification for safety
Á É Í Ó Ú
IEC 950 of information technology
UL 1950 equipment including electrical
á é í ó ú
business equipment
EN 55022 Specification for limits and
ì ò !
Class B methods of measurement of
radio interference
followed by the
SYM
characteristics of information
or to select a technology equipment.
<
<
FCC pt15 Federal communications
Sub pt B commission radio frequency
Class B emissions.
Written by DAW Publications, Cambridge
Power supply
Insert five size AA alkaline or
nickel-cadmium re-chargeable
batteries, observing the polarity
markings.
Re-chargeable batteries must be
charged externally before use.
Connect the AC
adaptor plug here. Use
only the recommended adaptor.
Plugging in the AC adaptor
disconnects the batteries.
Note: Re-chargeable batteries will
not be charged.
45010
45011
45012
Changing the cassette
45013
45014
Ensure tape and ribbon is
45015
taught across mouth of
45016
cassette and tape passes
45017
between
45018
the guide posts
45019
before installing.
15030
15010
40030
DYMO 1000
Electronic Labelmaker

Instructions for Use

Cassette door
To remove the door, press in
where shown below then swing
the door open and lift it away.
When re-fitting, hold the door at
the angle shown below and
engage the tabs on the door in
the slots in the case.
Now close the door, ensuring
that the lever engages with the
ramp on the door as it closes.
Cover
slides
off.
Ensure this lever
engages with ramp on
door when closing.
Lift cassette
straight up
and out.
Label
cutter –
press to
Make sure that cut off
this switch is set printed
to the RIGHT label.
before installing
the cassette. A
notch in the
cassette will fit
over the switch
Ensure tape and ribbon are
when it is set positioned as shown between
correctly.
print head and pinch roller.
Cleaning
Use a ball pen or
pencil to hold down
interlock button.
Press
Use a cotton
bud and alcohol
to clean both
sides of cutter
blade regularly.
Check and clean
print head and
pinch roller
regularly using
cotton bud and
alcohol ONLY.
Press
here to
open
Push firmly
until cassette
clicks into
place.
Print head
TAPE
CASSETTE
DYMO 1000
3