Related Manuals for Dymo M1011
Summary of Contents for Dymo M1011
- Page 1 User Guide Guide D’Utilisation Bedienungsanleitung Guida per l’utente Guía del usuario Guia do Usuário Rhino M1011 www.dymo.com...
- Page 2 A Tape cassette door H Character selection window B Tape rollers I Cutting handle C Tape advance knob J Embossing adjustment screw D Start line K Cable tie slot entrance E Tape pawl L Hole punch entrance F Embossing handle M Tape exit G Embossing wheel N Trailer length guide...
-
Page 3: About Your New Label Maker
• Aluminium without adhesive (31000) • Stainless Steel (32500) You can also use a Reverse Image Wheel with the DYMO M1011 label maker. This wheel allows you to print mirror script labels that meet special requirements in the industry. Mirror labels are used on moulds or casts for metal or rubber injection, silicon casting, fiber glass applications, and so on. -
Page 4: Loading The Tape
Loading the Tape The DYMO M1011 is set to emboss non-adhesive aluminium tape. To load the tape roll 1. Hold the label maker in your left hand. 2. Open tape cassette door (A). 3. Insert roll of tape allowing the end to extend about 5 cm (2") through the label slot. - Page 5 Cutting the Label To cut the label 1. Squeeze the embossing handle half-way, several times until the tape extends from the front of the tape exit (M) by at least 2,5 cm (1"). Before cutting the tape, make sure the end of the tape extends beyond the edge of the cutting assembly so you can easily pull the label out.
- Page 6 Embossing the Label Avoid turning the embossing wheel at the same time you are squeezing the embossing handle. This can damage the character wheel. To emboss a label 1. Turn the character selection wheel (G) until the desired letter is centered in the window (H).
- Page 7 Embossing on Stainless Steel Label You may need to adjust the labelmaker to emboss properly when using stainless steel tape. To adjust for stainless steel label 1. Turn the adjustment screw (J) clockwise 3/4 to 1 turn. 2. Emboss the text as described in “Embossing the Label” on page 6. When you return to using aluminum tape, you may need to reverse this adjustment.
- Page 8 Retracting the Label You may want to retract the tape, for example, if the tape advanced too far or to center the text on the label. To retract the label 1. Pull back the pawl (E). 2. Turn the tape advance knob (C) counter-clockwise.
- Page 9 Removing the Label To remove the label 1. Retract the tape as described in “Retracting the Label” on page 8. 2. Open the tape cassette door (A) and remove the label. Use caution when removing stainless steel tape that may have sharp edges.
- Page 10 Centering the Text on the Label The trailer length guide (N) has positioning marks for a short (S) or long label (L). Use the marks on the guide to center the text on your label. To center the text on a long label 1.
- Page 11 Applying Self-Adhesive Labels Self-adhesive aluminum tape sticks permanently to any smooth, clean, and dry surface. To apply self-adhesive tape 1. Peel off the protective backing taking care not to touch the adhesive. 2. Press the label in place. 3. Apply firm pressure along the entire length to ensure good contact.
- Page 12 Punching Holes in Non-Adhesive Labels You can choose to punch one or two holes in non-adhesive labels so that the labels can be attached using screws, nails, rivets, and metal or plastic wires or ties. You can also punch a cable tie slot in one or both ends of the label.
-
Page 13: Changing The Wheel
Changing the Wheel You can replace the character wheel with a Reverse Image Wheel. To change the wheel 1. Remove the tape. 2. Unscrew the screw in the center of the embossing wheel (G) and remove the wheel. 3. Position the new wheel. 4. - Page 14 Hints for Trouble Free Operation Keep the following in mind when using the label maker: • Letters appear where you want spaces - You are probably squeezing the embossing handle too hard. • Letters overlap - The tape is slipping. This can happen when dirt or grease gets on the rollers.
-
Page 15: Warranty Registration
This DYMO M1011 has been manufactured under strict quality control and performance tested before leaving the factory. Within one year after purchase, DYMO will repair or replace, at its own option, the M1011 free of charge if sent prepaid by the purchaser to DYMO and found, in DYMO’s judgement, to be defective in materials or workmanship. - Page 16 Distributed by/Distribué par/Distribuido por: DYMO, Atlanta, GA 30328 ©2010 Sanford, L.P. www.dymo.com Imported into Canada by/Importé au Canada par Sanford Canada L.P., Oakville, ON L6J 3J3 En México importado y distribuido por: Newell Rubbermaid de México S. de R.L. de C.V.