Tandberg Dnam With Amplifier And Speakers; The Dnam Amplifier; The Dnam Loudspeaker Cabinet (Center Speakers); Integrated Stereo Speakers - TANDBERG MXP F8 Administrator's Manual

MXP
Contents Introduction
TANDBERG DNAM with Amplifier
and Speakers
The TANDBERG DNAM applies to:
•
TANDBERG 8000 MXP
•
TANDBERG 6000 Profile
MXP
•
TANDBERG 6000 MXP
•
TANDBERG Maestro MXP
The DNAM's, are described on the following pages
D14033.06—AUGUST 2010
Getting started The menu structure The settings library
TANDBERG DNAM (Digital Natural Audio Module)*
The DNAM audio system is built on two specially designed and
separate modules, the:
•
DNAM audio amplifier
•
DNAM loudspeaker cabinet
The DNAM loudspeaker cabinet is based on several editions. For
the 6000 MXP
integrated in the loudspeaker cabinet. For the Maestro
the amplifier and the loudspeaker cabinet is integrated directly into
the system pedestal.

The DNAM Amplifier*

•
3 x 50W continuous average Center Output Power (load
specified by DNAM Center Speakers).
•
2 x 50W continuous average Stereo Output Power (load
specified by TANDBERG Loudspeaker Stereo Kit).
•
Full dynamic range for audio (high fidelity range) or Integrated
stereo speakers.
•
Digital Signal Processing and Filtering on all channels for best
audio detail clarity.
•
Digital Crossover Filtering on center channels.
•
In/out:
•
Audio In - SPDIF (stereo) or Analog (mono), using the same
connector.
•
Differential In - (female XLR pinout: 1 - GND, 2 – Signal (+), 3 –
Signal (-))
•
Loop Out - line out directly from the input, always analog even
with SPDIF in.
•
Stereo Out - (male XLR, common GND configuration)
•
Fuse 2A 250V Slow, 5 x 20mm, Littelfuse type 215002.
* The high-end TANDBERG systems can have different solutions on integrated audio
modules and speakers. Please contact your TANDBERG representative for more
information.
** Integrated stereo speakers are available with the 3000
Profile only.
Using the system Physical interfaces
and the 8000 MXP system, the audio amplifier is
MXP
MXP Profile and 6000
Peripheral equipment Peripheral equipment

The DNAM Loudspeaker Cabinet (Center Speakers)*

•
3-way Center Speaker system
•
Frequency range 50Hz - 20kHz
•
2 x 130mm low- and midrange loudspeakers, 8 ohms nominal, high
quality
•
1 x 25mm dome tweeter, 6 ohms nominal, high quality
•
Crossover filtered audio signals received from DNAM amplifier
•
system Long time max power 90 Watt on all loudspeakers
•
Enclosed MDF speaker cabinet

Integrated Stereo Speakers**

•
2 * 15W Stereo Speakers, high quality
•
Frequency range 100Hz - 20kHz
•
Enclosed MDF speaker cabinet
Using the external and optional Stereo Speaker Kit will improve the
stereo sound, even on systems with integrated stereo speakers**. Note
that the Stereo Speaker Kit is not available for Mini-DNAM.
IMPORTANT! Before connecting the Stereo Speaker Kit, make sure the
complete video communication system is powered down.
When connecting the Stereo Speaker Kit to a system with already
integrated stereo speakers, these integrated speakers will be disabled,
and a new filter and specification setup is loaded when powering up the
video communication system.
Read about Stereo Speaker Kit

Interface Required for Playback

For playback, a system with one video input and one audio input
without integrated echo cancellation is required.
MXP
Administrator Guide
Appendices Contact us
in the Peripheral equipment section.
310