Page 1 User Manual Software version F3 D13833.01 This document is not to be reproduced in whole or in part without permission in writing from:...
Page 2: Trademarks And Copyright
The information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be construed as a commitment by TANDBERG. The information in this document is believed to be accurate and reliable; however TANDBERG...
Page 3: Environmental Issues
Waste handling There is no need to send any products or material back to TANDBERG as there are no consumables to take care of. Please contact your local dealer for information on local waste handling and recycling of electronic products.
Page 4: Operator Safety Summary
TANDBERG 6000 MXP Profile Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions.
Page 5  ISDN cables - CAUTION - To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.  Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty.
Page 6 TANDBERG 6000 MXP Profile Contact us If you have any questions, comments or suggestions, please see the Online Support service at www.tandberg.net. It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O.
Page 7: Table Of Contents
3.10 Camera Control... 72 3.10.1 Move Camera ... 73 3.10.2 Far End Control... 74 3.10.3 Camera Presets ... 75 3.10.4 TANDBERG Tracker... 76 3.10.5 Picture Control ... 77 3.10.6 Camera Tracking ... 78 3.11 Presentation ... 79 3.11.1 Presentation Key... 80 3.11.2...
Page 8 TANDBERG 6000 MXP Profile 3.12 Conference Services... 87 3.12.1 Request Floor and Release Floor... 90 3.12.2 Conference Layout... 91 3.12.3 Terminal Names... 92 3.12.4 Chair Control... 93 3.12.5 Assign Floor and Release Floor from Participant ... 94 3.12.6 View Site and End View... 95 3.12.7...
Page 9 5.2 Document Camera... 231 5.3 DVD / VCR ... 232 5.4 Additional Cameras... 234 5.5 Additional Microphones... 235 5.6 The TANDBERG DNAM and Speakers... 237 5.7 Stereo Speaker Kit... 241 5.8 Telephone Add-On... 243 5.9 Dual Monitor... 244 5.10 XGA Monitors and Projectors ... 245 5.11 VESA Display Power Management ...
Page 10 TANDBERG 6000 MXP Profile 6.13 Appendix 13 ... 273 6.14 Appendix 14 ... 274 6.15 Appendix 15 ... 276 6.16 Appendix 16 ... 281 6.17 Appendix 17 ... 282 Glossary ... 286 Index... 295...
Page 11: Introduction
1 Introduction The TANDBERG 6000 MXP Profile provides high-end performance features, large monitors and precision audio. This creates a collaborative meeting environment for medium to large-sized meeting rooms. Audio Quality High-performance audio provides a richer, more complete visual communication experience. The MPEG4 AAC-LD standard is used to provide true standards-based CD-quality audio.
Page 12 Supporting DuoVideo/H.239, encryption and H.264.  Rate matching and Transcoding MultiSite. The TANDBERG videoconferencing system can also be used purely as an audio-bridge (with an ISDN connection). Presentations The Natural Presenter Package* (NPP) makes it possible to run presentations and comprises: ...
Page 13 Introduction Interoperability The TANDBERG 6000 MXP Profile is worldwide compatible with other standards-based videoconferencing systems. * - optional feature. To check which options are installed, select Control Panel - System Information in the menu. - TANDBERG First...
Page 14: At A Glance
TANDBERG 6000 MXP Profile 1.1 At a Glance TANDBERG 6000 MXP Profile Wall Mount TANDBERG 6000 MXP Profile Roll About WAVE II Camera The main camera is mounted on top of the product. The main camera includes a high quality color camera with a fast pan/tilt/zoom action.
Page 15 The main monitor displays the far-end and near-end videoconferencing sites in addition to the menus and video from connected video sources. Note that the TANDBERG 6000 MXP Profile is shipped with different monitors depending on product variants; there are two different variants of the system: 43”, which has a 43” monitor and the 50”...
Page 16 TANDBERG 6000 MXP Profile Microphone The high quality table microphone is designed to be placed on a table during a videoconference. Up to three microphones can be connected. The ideal location for the microphone is on a flat surface at least 2m (6.5 ft) from the front of the system. The system will automatically equalize sound levels.
Page 17 Introduction camera preset 10 to 15, the numbers A to F should be selected. For more information, contact your local TANDBERG representative.
Page 18: Menu Structure
TANDBERG 6000 MXP Profile 1.2 Menu Structure The menu structure is divided in two. The Main Menu is available for all users and contains all functionality of the system. The Administrator Menu contains all the settings of the system. The Administrator Settings are accessible from the Main Menu by selecting Control Panel and Administrator Settings.
Page 19 Introduction...
Page 20: Installation
2 Installation Precautions:  Never install communication wiring during a lightning storm.  Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations.  Never touch uninstalled communication wires or terminals unless the telephone line has been disconnected at the network interface.
Page 21: Unpacking And Mounting
2.1 Unpacking and Mounting Unpacking To avoid damage to the unit during transportation the system is delivered as separate components:  System  Column and Foot  Base, optional  High quality monitor  Wall Brackets  Camera  Camera stand The Accessories box contains the following: ...
Page 22 TANDBERG 6000 MXP Profile Mounting Please refer to the Installation sheet provided with the system for details on how to mount the TANDBERG 6000 MXP Profile. Note! The camera should be aligned with the front edge of the monitor to ensure that the IR-...
Page 23: Connecting Cables
2.2 Connecting Cables All cables needed in standard configuration are already connected to the codec. Connect these cables to their respective parts of the system. 1. Power cables Connect the power cable to an electrical distribution socket. 2. Monitor cables Connect the DVI cable to the input on your monitor.
Page 24: Monitor Configuration
TANDBERG 6000 MXP Profile 2.3 Monitor Configuration The monitor is pre-configured and only needs to be switched on.
Page 25: System Configuration
2.4 System Configuration The system must be configured for each installation. Configuration settings can be made via the system menu. If an external IMUX or non-standard network is being used it may be necessary to configure any associated external equipment. Navigate through the menu system using the arrow keys and OK.
Page 26 6. Screen Settings When using wide screen (16:9) monitors, set TV Monitor Format to Wide (16:9). TANDBERG also recommends setting Picture Layout to Picture outside Picture when using 16:9 monitors. Picture outside Picture provides a display layout optimized for wide screen monitors. The display layout may be changed at any time using the Layout button on the remote control.
Page 27 4. Network Profiles Please refer to Network Profiles 5. Data Port Please refer to Data Port for details 6. Save changes Remember to save any changes made in the menu by selecting the Save button on the Menu line and pressing OK. for details Installation...
Page 28: General Use
3 General Use Wake up the system When the system is not in use, it is in standby mode and the screens are black. Wake up the system by picking up the remote control. An incoming call or pressing any key on the remote control will also wake up the system.
Page 29: The Welcome Screen
3.1 The Welcome Screen When the system is switched on, the welcome screen will be displayed. The welcome screen presents the menu and displays your main camera image in the background (main camera is system default). The ISDN/IP numbers and the system name are displayed in the upper right corner.
Page 30: Using The Remote Control
TANDBERG 6000 MXP Profile 3.2 Using the Remote Control The system is controlled with a remote control. Think of the remote control as a mobile phone with number keys and call keys. Use the arrow keys and OK to navigate the menu. The system’s most commonly used functions are also accessible directly from the remote control.
Page 31 *This does not apply to all systems with small integrated cameras. 12. Selfview displays your outgoing video. Press Selfview again to turn selfview off, see Selfview. 13. Use the Phone Book to store and recall video contacts for easy placement of calls, see Phone Book.
Page 32: Navigation
TANDBERG 6000 MXP Profile 3.2.1 Navigation Arrow keys and OK Navigate in the menu with the arrow keys on the remote control. The orange selector on screen shows the selected item. Press OK to select. Cancel key In the main menu, pressing Cancel (X) will hide the menu. If the menu is hidden, bring it back with OK.
Page 33: Selfview
3.2.2 Selfview The term “Selfview” means the outgoing image. In a normal call, using main camera, this is the image of your self. The Selfview button toggles the images between Far End, Selfview and Dual Video (if any). How to use Selfview: 1.
Page 34 TANDBERG 6000 MXP Profile Example: You are using the system as a PC and get an incoming call. When the setting “Use Screen as Local PC monitor” is On, you will keep your PC image displayed locally and the incoming call pops up in a PIP or as smaller images in a 1+3 layout, depending on your system.
Page 35: Layout
General Use 3.2.3 Layout The layout of the screen can either be shown as Picture in Picture (PIP) or Picture outside Picture (POP) when displaying more than one video image. The behaviour of the Layout button is dependent on the Picture Layout setting in Screen Settings.
Page 36: Mic Off
TANDBERG 6000 MXP Profile 3.2.4 Mic Off To mute the microphone during a call, press the Mic off button. An on-screen indicator appears in the upper right corner when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash.
Page 37: Volume + And
General Use 3.2.5 Volume + and - Press the Volume key to adjust the volume level of the codec only and not the monitor. An on- screen indicator will show the current level.
Page 38: Number And Letter Keys
TANDBERG 6000 MXP Profile 3.2.6 Number and Letter keys Pressing a number key when outside a call will bring up the call menu. When in a call, the number keys are used for Camera Presets. Press a number and go to the corresponding Camera...
Page 39: Touch Tones
General Use 3.2.7 Touch Tones If wanting to dial extension numbers during a call, press the Touch tones button to activate the number keys, otherwise the number keys will activate the corresponding camera presets. An indicator will tell that Touch tones are enabled. Finish with OK to exit Touch tone mode.
Page 40: On-Screen Indicators
TANDBERG 6000 MXP Profile 3.3 On-screen Indicators The system has a number of icons signaling different settings: Microphone Off This indicator is shown when the microphone is turned off. Press the Mic off button again to turn the microphone back on, see Volume Off This indicator is shown when the volume is turned off.
Page 41 General Use Telephone This indicates that there is a telephone participant in the conference. The displayed number indicates how many telephone participants there are in the conference.
Page 42: Using The Menu
TANDBERG 6000 MXP Profile 3.4 Using the Menu Main menu outside a call and in a call. Press the Menu button on the remote control to display the menu. The menu contains all functions needed in order to control the system.
Page 43 The menu contains the following items:  Make a Call/Add Another Call  Standby/End Call  Camera Control  Presentation  Conference Services  Control Panel  Close Menu Structure for a full overview of the menu. The functions of the menu are displayed as icons. The currently selected icon is marked by an orange square, and the name of the corresponding function is displayed on the line above, see the figure above.
Page 44: Make A Call
1. Select Make a Call from the menu, or 2. Press the green Call button on the remote control The TANDBERG system can make both Call Settings specifies the quality of the call. It is possible to alter the default call settings for the current call if required.
Page 45: Place Video Call
3.5.1 Place Video Call In the Make a Call menu enter the Dial Number either: 1. Manually, or 2. Select the book symbol in order to display the participant. When dialing manually, toggle between ABC/abc by pressing the # button on the remote control and between abc/123 by holding the # button for one second.
Page 46: Place Telephone Call
TANDBERG 6000 MXP Profile 3.5.2 Place Telephone Call In the Make a Call menu enter the Dial Number either: 1. Manually, or 2. Select the book symbol in order to display the Phone Book and select a conference participant, see...
Page 47: Add Call
3.5.3 Add Call (optional feature) Conference systems with built-in MultiSite can handle up to 6 video calls and 5 telephone calls simultaneously. It is possible to both set up a conference with many participants and also add participants during a conference. Set up a conference with two or more participants In the Make a Call menu enter the Dial Number either: 1.
Page 48 TANDBERG 6000 MXP Profile...
Page 49: Call Settings
3.5.4 Call Settings The Call Settings specifies the quality of the call. Each call will be set up with the Default Call Settings if the settings are not altered. In this case the field is named Default Call Settings. If the settings for some reason are altered for the current participant in the current call, the name of the field will be changed to reflect this.
Page 50: Streaming
TANDBERG 6000 MXP Profile 3.5.5 Streaming Streaming lets you broadcast your meeting to participants on web. The web participants can listen to the meeting, see snapshots, but not participate themselves. Snapshots of current stream (if MultiSite), selfview, far end and DuoVideo streams are accessible via http. See descriptions of the possible snapshot files.
Page 51  Streaming Auto: Enables streaming of both local and far end video. Source* Selection of which site to be streamed is done using voice switching (the site that speaks is streamed).  Local: Only the local video will be streamed. ...
Page 52: Answer An Incoming Call
TANDBERG 6000 MXP Profile 3.6 Answer an incoming call How to answer an incoming call:  To accept an incoming call, press the OK button or the green Call button on the remote control. How to reject an incoming call: ...
Page 53: End Call
3.7 End Call How to end a call:  Press the red End Call button on the remote control, or  Press the Menu button on the remote control to display the menu and select End Call. When the End Call dialog box is displayed either: ...
Page 54: Standby
TANDBERG 6000 MXP Profile 3.8 Standby The system will automatically go to Standby mode when it is not in use. In standby mode, the screen(s) are black. It is however still possible to receive incoming calls. How to turn on the standby mode manually: ...
Page 55: Delay Standby For 1 Hour
General Use 3.8.1 Delay Standby for 1 hour Delay Standby for 1 hour postpones the system from entering standby mode for 1 hour. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors. It is also possible to postpone the system from entering standby mode for 3 hours, see Delay Standby for 3...
Page 56: Delay Standby For 3 Hours
TANDBERG 6000 MXP Profile 3.8.2 Delay Standby for 3 hours Delay Standby for 3 hours postpones the automatic standby mode for 3 hours. This function is useful when using the monitors for a local presentation to prevent the system from automatically blanking the monitors.
Page 57: Do Not Disturb
General Use 3.8.3 Do Not Disturb To prevent the system from accepting any incoming calls, the function Do Not Disturb has to be activated. The caller will hear a busy tone when calling the system. The monitor will be black when Do Not Disturb is active, see figure below.
Page 58: Phone Book
TANDBERG 6000 MXP Profile 3.9 Phone Book The Phone Book is available via the Phone Book button on the remote control or from the Make a Call menu. Using the Phone Book is time saving and prevents the user from inadvertently calling the wrong number.
Page 59 The following information is available from the Phone Book:  Last Number Dialed  Missed Calls  Call History  My Contacts  Global Contacts General Use...
Page 60: Call Log
TANDBERG 6000 MXP Profile 3.9.1 Call Log The Call Log lists Last Number Dialed, Missed Calls and Call History allows the user to see which calls that are made in the past. The lists contain a maximum of 30 numbers and the numbers are stored in these lists until the system is restarted.
Page 61: My Contacts
3.9.2 My Contacts My Contacts are the locally stored contacts on the system. This means that it is possible to add new contacts and edit or delete existing contacts. My Contacts can store up to 200 contacts. How to make a call using My Contacts: 1.
Page 62 TANDBERG 6000 MXP Profile The following functions are available from My Contacts:  Call Now  New Contact  New MultiSite Contact  Edit Contact  Delete Contact  Close...
Page 63 3.9.2.1 Add New Contact The New Contact function is available from Add a new contact to My Contacts by: 1. Select the New Contacts button to open the New Contacts dialog box. 2. Enter Name by using the letter keys on the remote control. Input will automatically be interpreted as letters.
Page 64 TANDBERG 6000 MXP Profile 3.9.2.2 New MultiSite Contact (Optional feature*) The New MultiSite Contact function is available from It is possible to pre-define the participants of a conference meeting as a MultiSite Contact. All participants in the MultiSite Contact will then be connected automatically instead of having to call the participants one by one.
Page 65 The two participants' bandwidth exceeds the maximum bandwidth. The system will then downspeed so that each participant connects with equal bandwidth, i.e. 512kbps/2 = 256kbps. * The MultiSIte option is not available on the TANDBERG 550 MXP, TANDBERG 770 MXP and TANDBERG 1000 MXP...
Page 66 TANDBERG 6000 MXP Profile 3.9.2.3 Edit Contact The Edit Contact function is available from How to edit a contact in the Local Phone Book: 1. Select the contact that is to be edited. 2. Press the left arrow on the remote control, followed by the down arrow until the Edit Contact icon is selected.
Page 67 3.9.2.4 Delete Contact The Delete Contact function is available from How to delete a contact: 1. Select the contact that is to be deleted. 2. Press the left arrow on the remote control, followed by the down arrow until the Delete Contact icon is selected.
Page 68: Global Contacts
Global Contacts are available if the system is connected to an external management system like the TANDBERG Management Suite (TMS). These contacts cannot be changed locally by the system, only from the management system. If there is a need to modify the number or any settings of a contact before making a call, select the contact and press OK on the remote control.
Page 69 General Use 3.9.3.1 Up one Level Global Contacts can be arranged in a tree structure with several sub folders. Use the Up one Level button to navigate up in the tree structure. When a search in the Global Phone Book is made, by using the Search function, only contacts matching the search text are displayed.
Page 70 TANDBERG 6000 MXP Profile 3.9.3.2 Search The phone book can contain an unlimited amount of global contacts. Using search makes it easier to find the wanted contact. How to search in the Global Phone Book: 1. Select the Search icon.
Page 71 3.9.3.3 Copy Contact to My Contacts The Copy Contact to My Contacts function is available from the Last Number Dialed, Missed Calls, Call History and Global Contacts folders, see It may be wise to copy contacts that are often used to My Contacts. Note that the local copy will not be updated if the Global Contacts are updated from the management system.
Page 72: Camera Control
Use Camera Presets, see  Adjust focus, brightness and whitebalance, see  Use Automatic Camera Tracking, see  Use the TANDBERG Tracker, see separate instructions included with the TANDBERG Tracker. for details. Camera Presets for details. Picture Control Camera Tracking for details.
Page 73: Move Camera
3.10.1 Move Camera It is possible to move the camera with the remote control or via the menu. Moving the camera directly with the remote control When the menu is hidden, the arrow keys will work on the camera. If the menu is displayed, press the Cancel button on the remote control to hide it.
Page 74: Far End Control
TANDBERG 6000 MXP Profile 3.10.2 Far End Control Far End Control allows you to control your conference partner’s camera. Far End Camera Control is useful if e.g. it is not possible to see what a participant at the far end is writing on their white board.
Page 75: Camera Presets
3.10.3 Camera Presets Use camera presets to easily vary between predefined near end camera angles. This is useful when pictures from many different camera angles have to be sent to the far end. E.g. in a meeting there is a white board, a PC and a small meeting table. Use camera presets to move between these camera angles in order to present the correct information to the participants at the far end without having to move the camera manually every time.
Page 76: Tandberg Tracker
TANDBERG Tracker How to save presets for the TANDBERG Tracker: 1. Select which camera preset to be used on the TANDBERG Tracker. 2. Move the camera to the desired position to store on the tracker. 3. Select Move Camera - Save New Preset in the menu.
Page 77: Picture Control
3.10.5 Picture Control Focus, Brightness and White balance are set for auto focus, auto brightness and auto white balance by default. If you need to set focus, brightness and white balance manually, go to Picture Control in the Camera Control menu. Focus Auto Auto focus continuously updates the focus throughout the call.
Page 78: Camera Tracking
TANDBERG 6000 MXP Profile 3.10.6 Camera Tracking Through Camera Tracking and the use of two or three microphones, the camera can automatically position itself on the current speaker. Before using camera tracking, the camera positions used must be stored at Preset 7 (Mic1), Preset 8 (Mic2) and/or Preset 9 (Mic3).
Page 79: Presentation
General Use 3.11 Presentation The Presentation Functionality in the system enables you to show other available video sources in addition to your Main Camera. This is perfect for meetings where you would like to show a PowerPoint presentation for instance. You can even use arrow keys up and down on the remote control to activate Page Up/Down on the PC (this only applies when using VNC).
Page 80: Presentation Key
TANDBERG 6000 MXP Profile 3.11.1 Presentation Key The quickest way to show a presentation is to use the presentation key on the remote control. The presentation key is used to start and stop a presentation. The presentation key will display PC (default*) or the last used presentation source.
Page 81: Presentation Menu
3.11.2 Presentation Menu The Presentation menu offers you all available video sources; Main Camera, PC, Document Camera, VCR, AUX and VNC. All these sources can be used as Main Video Stream or Dual Video Stream (Duo Video / H.239). Not all systems has all video sources available, see for details.
Page 82: Pc Presenter (Dvi/Xga Input)
TANDBERG 6000 MXP Profile 3.11.3 PC Presenter (DVI/XGA Input) (Optional feature - not available on all systems) Users often have their presentations on a laptop that is brought into the meeting room. Remember to connect your PC to the codec before you press the Presentation button. Note that the image will appear smoother on the system if your presentation is already displaying in full screen on your PC prior to connecting your PC to the video system.
Page 83: Pc Soft Presenter And Vnc
3.11.4 PC Soft Presenter and VNC (Optional feature) PC SoftPresenter is used to display PC images on your system without using a VGA cable (PC Presenter). The system and your PC must be connected to the same LAN. In addition, VNC (Virtual Network Computing) server software must be installed on the PC.
Page 84: Dual Stream (Duovideotf/H.239)
TANDBERG 6000 MXP Profile 3.11.5 Dual Stream (DuoVideoTF/H.239) (Optional feature - not available on all systems) With Dual Stream you have the opportunity to show two different live video streams simultaneously, main video and one additional source. This is handy when showing a presentation.
Page 85: Take New Snapshot
3.11.6 Take New Snapshot The system can take a snapshot of your live video. Snapshot is handy when you are in a call with a system that does not support Dual Stream. Use Snapshot to show a snapshot of your presentation and continue the meeting with main camera.
Page 86: Display Snapshot
TANDBERG 6000 MXP Profile 3.11.7 Display Snapshot The system stores the last sent or received Snapshot. The snapshot is deleted automatically after the call. How to display snapshots: 1. To view a stored snapshot, first choose the Snapshot header. 2. Select Display Snapshot in the Presentation menu.
Page 87: Conference Services
General Use 3.12 Conference Services A Multipoint Control Unit (MCU) enables several sites to participate in the same conference. During an MCU conference, the status line will provide information about the conference. You can make a multipoint conference in different ways. The Conference Services vary depending on how you make the call, see Add call for details.
Page 88 Using the system’s internal MCU, MultiSite Most TANDBERG MXP systems has an optional built-in MCU, which is called MultiSite*. It supports up to 6 video calls and 5 telephone calls including yourself for high-end systems, and 4 video calls and 3 telephone calls including yourself for the mid- and lower end systems. The MultiSite supports both Split Screen and Voice Switched mode.
Page 89 With an external MCU that does not support H.243, you have the following services:  Request/Release Floor  Terminal Names * The MultiSIte option is not available on the TANDBERG 550 MXP, TANDBERG 770 MXP and TANDBERG 1000 MXP General Use...
Page 90: Request Floor And Release Floor
TANDBERG 6000 MXP Profile 3.12.1 Request Floor and Release Floor When requesting floor, your video will be broadcasted in full screen to all other participants in the conference. Request Floor is useful when you want to speak or display something in front of all participants.
Page 91: Conference Layout
Switch between these picture modes using the Conference Layout menu. Continuous Presence layout 4 split Voice Switched mode * The MultiSite option is not available on the TANDBERG 550 MXP, TANDBERG 770 MXP and TANDBERG 1000 MXP...
Page 92: Terminal Names
TANDBERG 6000 MXP Profile 3.12.3 Terminal Names Choose Terminal Names to see a list of the participants of the MultiSite conference. Press Cancel to go back.
Page 93: Chair Control
3.12.4 Chair Control (Not supported by TANDBERG MCU, TANDBERG MPS or MultiSite) As chairman, you have access to more MultiSite Services. Select Chair Control to assume the role of chairman of the conference. Select Release Chair to end the role as chairman. A Chair...
Page 94: Assign Floor And Release Floor From Participant
TANDBERG 6000 MXP Profile 3.12.5 Assign Floor and Release Floor from Participant Assign Floor allows the chairman to select which of the conference participants that is to be broadcasted to all other participants.
Page 95: View Site And End View
General Use 3.12.6 View Site and End View (Not supported by TANDBERG MCU or MultiSite) View Site allows you to view any participant in the conference regardless of whom having floor and chair. Choose End View to go back to normal.
Page 96: Disconnect Participant
TANDBERG 6000 MXP Profile 3.12.7 Disconnect Participant Disconnect Participant allows the chairman to disconnect any participant in the conference. In a multipoint call, this is equivalent to disconnecting a participant from the end call menu.
Page 97: Terminate Meeting
General Use 3.12.8 Terminate Meeting Terminate Meeting allows the chairman to terminate the conference altogether. In a MultiSite call, this is equivalent to pressing End All Calls from the end call menu.
Page 98: More About Multisite (Embedded Mcu)
TANDBERG 6000 MXP Profile 3.12.9 More about MultiSite (embedded MCU) (Optional Feature*) Calling in to a MultiSite Any system can be part of a MultiSite conference by calling in to a MultiSite. The dial-in numbers to the MultiSite depends of the network that is used.
Page 99 In this case you get 26 participants in the cascaded MultiSite conference. Note that the illustrations may differ from the actual product. * The MultiSite option is not available on the TANDBERG 550 MXP, TANDBERG 770 MXP and TANDBERG 1000 MXP...
Page 100: Control Panel
TANDBERG 6000 MXP Profile 3.13 Control Panel The Control Panel contains the features:  Diagnostics  Text Chat  Audio Demonstration  Administrator Settings  Restart  User Guide...
Page 101: Diagnostics
3.13.1 Diagnostics Diagnostics allows testing of individual system components and displays the current system settings. Diagnostics contain:  System Information  Channel Status  Call Status  System Selftest  View Administrator Settings  IP Address Conflict Check  Warnings General Use...
Page 102: System Information
TANDBERG 6000 MXP Profile 3.13.1.1 System Information Select System Information to view system numbers, line status, software version, hardware serial number and other useful information. Press arrow key up and down to scroll in the System Information list. System Information contains:...
Page 103: Channel Status
Invalid information element contents Recovery on timer expiry Internetworking, unspecified TANDBERG specific. undefined cause code PRI Red Alarm Red alarm or Loss of signal (LOS) means that there is no signal and thus no framing info received (this has same effect as pulling out the PRI cable).
Page 104 TANDBERG 6000 MXP Profile PRI Yellow Alarm Yellow alarm or Remote Alarm Indicator (RAI) means that the system is receiving framing info, but in this framing info the other side tells the system that it is not reading the system’s transmitted framing info.
Page 105: Call Status
General Use 3.13.1.3 Call Status Comprehensive information about the call is available through the Call Status window. The menu has two columns, one for transmitted and one for received audio/video/data information. If Dual Stream or MultiSite is available on your system and in use, pressing the UP/DOWN keys will show one page per connected site.
Page 106: System Selftest
TANDBERG 6000 MXP Profile 3.13.1.4 System Selftest The system performs a check to determine internal hardware integrity. System Selftest is useful when you want to check if your network connection is active.
Page 107: View Administrator Settings
3.13.1.5 View Administrator Settings This window displays all the system settings. Use the arrow key on the remote control to scroll through the list. View Administrator Settings may contain*: General Settings Screen Settings Software Options Menu Settings Presentation Settings VNC Settings System Name Language Dual Monitor...
Page 108 TANDBERG 6000 MXP Profile Video Quality Default Call Settings Audio Settings Inputs Level Settings Outputs Level Settings Echo Control Audio Levelling (AGC) Alert Tones & Volume Video Settings Main Camera Document Camera Split Screen Call Type Network Bandwidth Restrict (56k)
Page 109 Picture Control Video Name Network Type Advanced ISDN Settings ISDN-PRI Settings Channel Hunting Advanced ISDN PRI Settings Leased E1/T1 Settings External network configuration Focus White balance Brightness Main Cam Doc Cam ISDN-BRI\PRI\Leased E1\T1\Enternal H331 ISDN Switch Type ETSI (Euro ISDN),… Line1 Setup On Number1 Number2...
Page 110 TANDBERG 6000 MXP Profile IP Settings H.323 Settings Advanced H.323 Settings IP Precedence Diffserv SNMP Settings Streaming Settings Network Profiles Security Data Port 1 Data Port 2 * The administrator settings available will vary within the MXP system range depending on system and what software options installed.
Page 111: Ip Address Conflict Check
General Use 3.13.1.6 IP Address Conflict Check The system will give a warning if there is an IP conflict. The user may initiate this check by selecting IP Address Conflict Check.
Page 112 TANDBERG 6000 MXP Profile 3.13.1.7 Warnings If any warnings registered by the system it will be displayed in the Warnings menu. Open a warning in the list to get more information about the warning. The following warnings may be displayed if detected by the system, depending on system type...
Page 113  There is something wrong with the Leased E1/T1 line (Yellow alarm). Please check your network connection. (193) H323 gatekeeper warnings  Could not register to the gatekeeper.  The gatekeeper rejected to register the system. Another system is already registered with the same alias or H.323 ID.
Page 114: Text Chat
TANDBERG 6000 MXP Profile 3.13.2 Text Chat While in an ISDN or IP call to another system supporting Text Chat (T.140), select Text Chat from the Control Panel. Enter text in the displayed window. How to use Text Chat: 1. Choose Text Chat from the Control Panel to open the Text Chat window.
Page 115: Audio Demo
General Use 3.13.3 Audio Demo Note that the Audio demo will only appear in the User Guide if a Digital Natural Audio Module is connected to the codec.
Page 116: Administrator Settings
TANDBERG 6000 MXP Profile 3.13.4 Administrator Settings Administrator Settings contains the configuration of the whole system. It is recommended to password protect Administrator Settings to prevent occasional users to make changes to the system. See Administrator Settings for further details.
Page 117: Restart
General Use 3.13.5 Restart Restart the system by pressing the Restart button. You are prompted with a dialog box saying: Do you want to restart the system? Press OK to restart, press Cancel (X) to abort.
Page 118: User Guide
TANDBERG 6000 MXP Profile 3.13.6 User Guide The on screen user guide takes you through a quick step-by-step introduction to videoconferencing. It gives the user basic skills in how to use the system.
Page 119: Administrator Settings
4 Administrator Settings Administrator Settings contain all the settings of the system. Making changes to Administrator Settings will change the behavior of the system. It is recommended to password protect the access to Administrator Settings to prevent occasional users from making crucial changes to the system, see Administrator Password.
Page 120: General Settings
TANDBERG 6000 MXP Profile 4.1 General Settings When installing the system, go through the General Settings menu to ensure that you have the right settings for your system, see System Configuration. General Settings contain:  Language  System Name ...
Page 121: Language
Administrator Settings 4.1.1 Language The system supports 15 different languages for its on-screen menus; English, German, French, Norwegian, Swedish, Italian, Spanish, Portuguese, Chinese Simplified, Chinese Traditional, Japanese, Russian, Korean, Finnish and Thai. Select the preferred language and press OK to save.
Page 122: System Name
TANDBERG 6000 MXP Profile 4.1.2 System Name System Name identifies the system:  On the welcome page.  During an MCU conference call.  When using the Web-interface.  When the codec is acting as an SNMP Agent.  Towards a DHCP server.
Page 123: Dual Monitor
4.1.3 Dual Monitor TANDBERG systems can be used with both one and two monitors. If you use two monitors, make sure that Dual Monitor is set to "On". Selfview, snapshots and Dual Stream will be displayed on the second monitor.
Page 124: Auto Answer
TANDBERG 6000 MXP Profile 4.1.4 Auto Answer The auto answer setting decides whether an incoming call is put through automatically or manually. The system will automatically answer all incoming calls. On+Mic Off The system will automatically answer all incoming calls and switch the microphone off when the call is connected.
Page 125: Max Call Length
Administrator Settings 4.1.5 Max Call Length This feature will automatically end both incoming and outgoing calls when the call time exceeds the specified Max Call Length. Max Call Length can have the following values: 0-999 (minutes), where 0 means off.
Page 126: Phone Book Settings
TANDBERG 6000 MXP Profile 4.1.6 Phone Book Settings Corporate Directory The Corporate Directory is available in the menu. The Corporate Directory is hidden from the menu and is unavailable for users. IP address Enter the IP address of the management system that provides the Phone Book.
Page 127: Permissions
4.1.7 Permissions Permissions contains settings for incoming MCU Calls, incoming telephone Calls, Far End Control, Remote Software Upgrade and Fallback to Telephony. Access Code An access code will help you control the use of the system. All users must enter a code to identify themselves and the call will be charged on their account.
Page 128 TANDBERG 6000 MXP Profile Remote Software Upgrade It is possible to upgrade software remotely, i.e. a far end system may upgrade software on a local system via http on ISDN. The system to be upgraded must be configured to allow remote software upgrade.
Page 129: Screen Settings
4.1.8 Screen Settings Auto Layout If Auto Layout is On the system will change layouts automatically depending on the number of participants in a call and if you have a dual video stream or not. Please refer to Layout for more information. If Auto Layout is Off there will be no automatic layout changes during a call.
Page 130 TANDBERG 6000 MXP Profile Picture in Pressing the Layout button on the remote will result in an extra picture in Picture (PIP) smaller view (Picture in Picture). Press the Layout button to move it around in the corners of the screen and finally hide it. Pressing and holding Layout for 1 second will hide the small picture directly from any position.
Page 131 Note that if both TV monitor format and VGA format is set to Normal, the system will skip the 1+3 layout, which is not beneficial for 4:3 monitors. Note that the following menu settings do not apply for all TANDBERG MXP systems. Please refer to the actual menu page on your system.
Page 132 TANDBERG 6000 MXP Profile wide screen (16:9) monitor or projector. The VGA and DVI output will then be optimized for Wide Screen VGA and High Definition (HD) display. Normal Output format is optimized for Normal VGA monitors (4:3) Wide Output format is optimized for Wide VGA monitors (16:9) Wide screen VGA or TV monitor in Normal (stretched) mode.
Page 133 SVGA 800x600 VGA output format is forced to SVGA format (800x600) 75Hz 75Hz XGA 1024x768 VGA output format is forced to XGA format (1024x768) 60Hz 60Hz VGA Out Quality for Wide XGA: If VGA Monitor Format is set to Wide, PC Picture Format is set to Normal, VGA Out Quality is set to Auto, the layout on the monitor is either fullscreen or POP, and the input source to the largest window is PC with resolution 1024x768, the system will use WideXGA (1280x768) instead of XGA, when the monitor supports this.
Page 134 TANDBERG 6000 MXP Profile...
Page 135: Software Options
4.1.9 Software Options The system requires a valid option key to activate MultiSite and/or Presenter functionality. In order to activate additional bandwidth, you need to enter a bandwidth key. A restart of the system is required after entering a new option and/or bandwidth keys. If the key is invalid, the original key will be used.
Page 136: Menu Settings
TANDBERG 6000 MXP Profile 4.2 Menu Settings Menu Settings contain the settings:  Menu Timeout In Call  Welcome Menu  Welcome Picture  Logo  Menu on TV  Menu on PC  Balloon Help  Display Welcome Text ...
Page 137: Menu Timeout In Call
4.2.1 Menu Timeout In Call Main menu appears on the bottom line of the screen. Set Menu Timeout In Call to On if you want the menu to time out automatically when you are in a call. The menu will time out automatically after 15 seconds if there is no activity on the remote control.
Page 138: Welcome Menu
TANDBERG 6000 MXP Profile 4.2.2 Welcome Menu The Welcome Menu contains the Main Menu, System Status, your System Name and dial in numbers. The Welcome Menu is shown when the system wakes up from standby mode. The Welcome Menu is not shown when the system wakes up from standby mode.
Page 139: Welcome Picture
4.2.3 Welcome Picture The Welcome Picture is what you see in the background of the welcome menu. Selfview Selfview is shown in the background of the welcome menu. In most cases this means that main camera is displayed and you can see the video image of yourself.
Page 140: Logo
Choose On if you want the company logo to appear in the background of the welcome menu. The logo is not displayed. Note: The TANDBERG Logo will be displayed if no other company logo is load and logo is enabled.
Page 141: Menu On Tv
4.2.5 Menu on TV The Menu on TV setting decides if the menu shall be displayed on the TV screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On and vice versa. The menu is available on the TV screen.
Page 142: Menu On Pc
TANDBERG 6000 MXP Profile 4.2.6 Menu on PC The Menu on PC setting decides if the menu shall be displayed on the PC (VGA screen) screen or not. For optimal layout of the menu, Menu on TV should be Off if Menu on PC is On and vice versa.
Page 143: Balloon Help
4.2.7 Balloon Help It is possible to enable / disable the balloon help window. Choose On if you want help text windows to appear. There will be no help text window. Administrator Settings...
Page 144: Display Welcome Text
TANDBERG 6000 MXP Profile 4.2.8 Display Welcome Text The welcome text displays your system name and dial in numbers by default. It is possible to hide this information by choosing Display Welcome Text Off. Welcome text is displayed on the welcome menu.
Page 145: Welcome Text
Administrator Settings 4.2.9 Welcome Text You can change the welcome text to any text you like, instead of the default text. Remember that Display Welcome Text must be On to be able to edit the welcome text.
Page 146: Administrator Password
TANDBERG 6000 MXP Profile 4.2.10 Administrator Password It is recommended to put an Administrator Password on the system. The Administrator Password can be maximum 5 digits long. The Administrator Password dialog box will pop up when you choose Administrator Settings from the Control Panel. This will prevent occasional users from going in to administrator settings.
Page 147: Presentation Settings
4.3 Presentation Settings Presentation Settings contain:  Presentation Start  H.239  Startup Video Source  Presentation Source  Snapshot Source  Auto-Display Snapshot  PIP Appearance  PIP Placing  VNC Settings Administrator Settings...
Page 148: Presentation Start
TANDBERG 6000 MXP Profile 4.3.1 Presentation Start If your system has Dual Stream capabilities, you can show two video streams at the same time (see also Dual Stream). Presentation Start is Auto by default. This means that you will start Dual Stream (a second video stream) automatically when starting a presentation.
Page 149: H.239
4.3.2 H.239 H.239 supports transmission of two video streams. It combines elements of Duo Video and People+Content. If H.239 is disabled you will still be able to start TANDBERG Dual Video Stream* Enabled Enables H.239 Disabled Disables H.239 * The TANDBERG 550 MXP can only receive Dual Video Stream.
Page 150: Startup Video Source
TANDBERG 6000 MXP Profile 4.3.3 Startup Video Source The Startup Video Source is the video source on display when the system wakes up from standby mode. If you use Main Camera as start up source, the system will start with Main Camera every time the system wakes up from standby, regardless of what the previous user was using.
Page 151: Presentation Source
Administrator Settings 4.3.4 Presentation Source The Presentation Source is connected to the Presentation button on the remote. Pressing the Presentation button will put the Presentation Source on display. Presentation Source is PC by default*. You can change the Presentation Source to any video source and none. Choosing none results in opening the Presentation menu when pressing the Presentation key.
Page 152: Snapshot Source
TANDBERG 6000 MXP Profile 4.3.5 Snapshot Source When you take a Snapshot, you get a snapshot of the Snapshot Source. Current is the default Snapshot Source. This means that you take a snapshot of the video source that is currently active.
Page 153: Auto-Display Snapshot
4.3.6 Auto-Display Snapshot Select Auto to automatically display a received snapshot. Turn Auto-Display Snapshot Manual if you wish not to have them displayed on the screen when they are sent or received. The snapshots will be sent and received, but not displayed. With Auto-Display Snapshot set for Manual, you must enter the Presentation menu to display a snapshot.
Page 154: Pip Appearance
TANDBERG 6000 MXP Profile 4.3.7 PIP Appearance A Picture in Picture (PIP) is a smaller picture placed in one of the corners of the screen. The PIP enables you to see an extra picture in your video conference. Auto PIP Auto means that Picture In Picture will appear automatically when it is suitable.
Page 155: Pip Placing
4.3.8 PIP Placing PIP Placing lets you decide where the PIP shall appear. You can of course move the PIP with the Layout button on the remote anytime. Top Right PIP is placed in the Top Right corner. Bottom PIP is placed in the Bottom Right corner. Right Bottom PIP is placed in the Bottom Left corner.
Page 156: Vnc Settings
TANDBERG 6000 MXP Profile 4.3.9 VNC Settings VNC Settings is necessary when using a VNC presentation. See chapter for more information on how to use VNC. Address The IP-address of the PC with the VNC software installed. To find the IP- address of the PC, place the mouse pointer on the VNC program icon in the lower right corner of the Windows taskbar.
Page 157: Call Quality
4.4 Call Quality Call Quality contains the settings:  Video Algorithm  Audio Algorithm  AAC-LD 128kbps  Natural Video  Max Upstream Rate  Video Quality  Default Call Settings Administrator Settings...
Page 158: Video Algorithm
TANDBERG 6000 MXP Profile 4.4.1 Video Algorithm The system will automatically select the best video algorithm based on the video source and the capabilities of the remote system. Use this menu to disable video algorithms in case you have interoperability issues calling other systems.
Page 159: Audio Algorithm
* G.722 at 64kbps is used in H.323 (IP) calls only. ** G.711 at 64kbps is used in SIP and H.323 (IP) calls only. *** Dependent on a call rate above the AAC-LD 128 threshold. Note that this is not available on all TANDBERG systems. Administrator Settings...
Page 160: Aac-Ld 128Kbps (Stereo Audio)
TANDBERG 6000 MXP Profile 4.4.3 AAC-LD 128kbps (stereo audio) Specify a call rate for 128kbps AAC-LD. From this call rate and above, "128kbps AAC-LD" is available. On lower call rates "64kbps AAC-LD" is available. Stereo audio requires twice the bandwidth as mono CD-quality audio. Therefore we recommend to enable stereo audio on high call rates only.
Page 161: Natural Video
4.4.4 Natural Video Choosing Natural Video will enable 60 fields* per second true interlaced picture for high motion video. The use of Natural Video requires the H.263+ and H.263++ video protocols. Natural video will be disabled in H.323 MultiSite calls and in H.320 Continuous Presence MultiSite calls. Auto Natural Video Auto will enable transmission of Natural Video from 768 kbps and above.
Page 162: Max Upstream Rate (Kbps)
TANDBERG 6000 MXP Profile 4.4.5 Max Upstream Rate (kbps) The Max Upstream Rate (kbps) defines the desired maximum transmitted call rate. This is to be able to limit the outgoing bandwidth whilst keeping the maximum incoming bandwidth, especially useful for home offices with different upstream and downstream rates, typically ADSL.
Page 163: Video Quality
4.4.6 Video Quality The different video sources need different Video Quality Settings. Main Camera, VCR, AUX and Split Screen have Motion as default. PC, Document Camera and VNC have Sharpness as default. Motion Optimized for smooth motion video (CIF/SIF for low bandwidths, iCIF/iSIF for high bandwidths).
Page 164 TANDBERG 6000 MXP Profile Basic Video Video Input Quality MOTION MOTION NTSC MOTION MOTION SVGA MOTION SHARPNESS SHARPNESS NTSC SHARPNESS SHARPNESS SVGA SHARPNESS Transmission mode with Motion or Sharpness selections. 4.4.6.2 Native Resolutions The following live video resolutions are supported on the system: Native NTSC: ...
Page 165: Default Call Settings
4.4.7 Default Call Settings Default Call Settings are connected with unchanged when making a call, the system will use the Default Call Settings in the call. In addition to the Call Settings Call Type, Net, Bandwidth and Restrict (56k), you also find settings for H.320 Auto bandwidth and H.323 Auto bandwidth in Default Call Settings.
Page 166 TANDBERG 6000 MXP Profile number into an IP-address, see gatekeepers. Select ISDN to ensure that the call is set up as an ISDN call. Select H.323 to ensure that the call is set up as an H.323 call. Select SIP to ensure that the call is set up as an SIP call.
Page 167 H.221 or 2x64 (2x56) Calling Some older or low end video systems do not have the ability to make bonded ISDN calls. In these cases it is necessary to dial both ISDN numbers separately to call those systems. These types of calls are often referred to as ...
Page 168: Audio
TANDBERG 6000 MXP Profile 4.5 Audio Audio contains the settings:  Inputs  Outputs  Echo Control  Stereo Settings  Audio Levelling (AGC)  Alert Tones and Volume...
Page 169: Inputs
4.5.1 Inputs Mic 1- 3 and Audio input 4-6 By default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are On will automatically be mixed. Unconnected inputs will automatically be muted. Select Off to prevent audio/noise from connected but unused inputs.
Page 170 TANDBERG 6000 MXP Profile settings. The input level should be adjusted so that the average level reaches the preferred level marker. The audio inputs are adjustable in steps of 1.5 dB from 0 dB to 22.5 dB. The default levels for Mic 1,2 and 3 are set for use with an Audio Technica AT871R or AT841R microphone in an average videoconferencing room.
Page 171: Outputs
4.5.2 Outputs Audio out 1 - 3 Audio out 1 is intended for connection to TANDBERG Digital Natural Audio Module, televisions or audio amplifiers. Audio out 2 is intended for connection to audio recording equipment or to a telephone add-on hybrid.
Page 172: Echo Control
TANDBERG 6000 MXP Profile 4.5.3 Echo Control Mic 1-3 and Audio 4 Each of the 3 microphone inputs and Audio input 4 has a separate acoustic echo canceller. One echo canceller per input provides more sophisticated control than having one common canceller for all microphones.
Page 173  Avoid moving the microphone or loudspeaker.  In the presence of low frequency noise, enable the noise reduction (NR). Administrator Settings...
Page 174: Stereo Settings
TANDBERG 6000 MXP Profile 4.5.4 Stereo Settings Settings Out 1 Stereo I/O Mode* Mode Analog Analog Analog Analog SPDIF SPDIF SPDIF SPDIF *Out 1 Mode: Auto/Analog/SPDIF is described in Outputs. **L+R = Left + Right When Stereo I/O Mode is Off and Stereo Speakers is Off, the output response will be a mono loudspeaker signal on Audio out 1, AUX on Audio out 2 and VCR on Audio out 3 regardless on the Out 1 Mode setting.
Page 175 Note that if Stereo Speakers are enabled in the menu without having any stereo speakers connected to the Digital NAM, it may cause the acoustic echo-canceller to malfunction. If the system is connected to a Digital NAM, stereo sound on the loudspeakers shall be present if a stereo input signal is connected to the inputs VCR-Left and VCR-Right or a stereo signal is received from the Far End.
Page 176: Audio Levelling (Agc)
TANDBERG 6000 MXP Profile 4.5.5 Audio Levelling (AGC) Select On to allow automatic adjustments (Automatic Gain Control) of audio levels. When On, the AGC maintains the audio signal level at a fixed value by attenuating strong signals and amplifying weak signals. Very weak signals, i.e. noise alone, will not be amplified.
Page 177: Alert Tones And Volume
4.5.6 Alert Tones and Volume Video Call Alert Tone and Telephone Alert Tone To help distinguish between incoming video calls and ordinary telephone calls, it is recommended to use different ringing tones for video calls and telephone calls. Alert Volume You may change the volume level for the selected ringing tone.
Page 178: Video
TANDBERG 6000 MXP Profile 4.6 Video Video contains the settings:  Camera Tracking Mode  MCU Status Line  Floor to Full Screen  Web Snapshots  MultiSite Picture Mode  Video Name...
Page 179: Camera Tracking Mode
The system quickly zooms in on a single person speaking. Suitable when close- ups are preferred over wide-angle images. Note that the Camera Tracking Mode entry will not be available if not using the TANDBERG WAVE II Camera. Administrator Settings...
Page 180: Mcu Status Line
TANDBERG 6000 MXP Profile 4.6.2 MCU Status Line The MultiSite / MCU / DuoVideo indicators will be displayed and provide information about the conference. The MultiSite / MCU / DuoVideo indicators will not be displayed. Auto The MultiSite / MCU / DuoVideo indicators will be displayed for a few seconds and then timed out.
Page 181: Floor To Full Screen
4.6.3 Floor to Full Screen When "Floor to Full Screen" is enabled, someone who requests floor will be seen by all participants as full screen. When "Floor to Full Screen" is "Off", someone who request floor in a MultiSite conference using the 5+1 layout will be seen in the large square, rather than full screen. The participant that has floor is displayed in full screen regardless of what MultiSite layout that is used.
Page 182: Web Snapshots
TANDBERG 6000 MXP Profile 4.6.4 Web Snapshots The system is able to generate JPEG snapshots and provide them to the world outside by request (as ‘http get’ or via ftp). See Snapshots generation is enabled. Snapshots generation is disabled. Note that web snapshots are not generated if the conference is encrypted.
Page 183: Multisite Picture Mode
4.6.5 MultiSite Picture Mode MultiSite* Picture Mode decides the default layout of a MultiSite call. Choose between the layouts: Auto Split, 4 Split, 5+1 Split, and Voice Switched. You can change the layout during a call using the layout option in MultiSite Services. Auto Split Auto Split displays all participants on the screen simultaneously.
Page 184 TANDBERG 6000 MXP Profile Voice Switched mode...
Page 185: Video Name
Administrator Settings 4.6.6 Video Name As a default, the video inputs are given the names Main Cam, PC, Doc Cam, VCR, AUX or VNC, dependent on what video sources are available on your system. The video names cannot exceed eight characters. The names correspond to the video names in the Presentation Menu (Choose Presentation from the main menu and open the Main Video or Presentation Video pop up menu).
Page 186: Security
TANDBERG 6000 MXP Profile 4.7 Security Security contains the settings:  Encryption  Encryption Mode  Passwords...
Page 187: Encryption
4.7.1 Encryption (Country specific) Auto The system will try to set up calls using encryption. Point to point calls: If the far end system supports encryption (AES or DES), the call will be encrypted. If not, the call will proceed without encryption. MultiSite calls*: In order to have encrypted MultiSite calls, all sites must support encryption.
Page 188: Encryption Mode
TANDBERG 6000 MXP Profile 4.7.2 Encryption Mode Auto The system will try to use the most secure encryption - AES, dependent on the capabilities of the other sites. For sites that do not support AES encryption, DES encryption will be tried.
Page 189: Passwords
Administrator Settings 4.7.3 Passwords Administrator Password, IP Access Password, Streaming Password, VNC Password, Access Code and Remote Software Upgrade password are duplicated from their respective menus. Using the Security menu gives you a quick way to change all passwords of the system.
Page 190: Network
TANDBERG 6000 MXP Profile 4.8 Network The network menu contain:  ISDN/External/Leased E1/T1  LAN Settings  Network Profiles  Data Port...
Page 191: Isdn/External/Leased E1/T1
4.8.1 ISDN/External/Leased E1/T1 Network Before using the system it is necessary to specify which network to use and Type define its settings. ISDN- If you want to use your system via ISDN-BRI, you should select Network Type: ISDN-BRI and enter the ISDN BRI Settings menu to set the BRI parameters. ISDN- If you want to use your system via ISDN-PRI, you should select Network Type: PRI*...
Page 192 TANDBERG 6000 MXP Profile 4.8.1.1 ISDN-BRI Settings To make sure your system will work properly using ISDN-BRI, make the following settings: 1. Set ISDN switch type 2. Enter ISDN line numbers (+ SPIDs if required) 3. Disable unused lines Some software versions do not support 6 ISDN lines, therefore some of the Line Setup entries may be grayed out.
Page 193 Advanced ISDN Settings Sub address Using a sub address enables you to connect up to eight ISDN terminals to the same ISDN telephone number and line. The terminals are addressed by using different sub addresses. To call a terminal with a sub address, separate the ISDN telephone number and the sub address with a ‘*’.
Page 194 TANDBERG 6000 MXP Profile 4.8.1.2 ISDN-PRI Settings To make sure your system will work properly using ISDN-PRI, configure the following settings: 1. Set PRI switch type 2. Enter PRI line number Note that the T1 format is predefined to ESF and the line code is B8ZS. This is not configurable.
Page 195 Example: Max Channels may be used for PRIs that are provisioned for a lower number of channels. High Channel, Low Channel and Search may be used for PRIs provisioned with specific requirements for B-channel usage. In the example above, the system will start searching for available B-channels at channel 20, since Search is set to High and High Channel is set to 20.
Page 196 TANDBERG 6000 MXP Profile Advanced ISDN-PRI Settings NSF is a non standard facility. Your network provider may require a service selection in your ISDN configuration. Enter the Service code here. Valid NSF service codes are from 1 to 31. Enter 0 to disable NSF service codes.
Page 197: Leased E1/T1 Settings
4.8.1.3 Leased E1/T1 Settings Call Control Auto When Auto is selected, the system will automatically initiate a connection as soon as it detects that the far end tries to make a call. This mode is also commonly known as "data triggered" mode, because the existence of certain data patterns on the line triggers a connection.
Page 198: External Network Settings
TANDBERG 6000 MXP Profile 4.8.1.4 External Network Settings Before using the system together with external network equipment, you must specify the network parameters on this page. The system has support for up to 2 Mbps (depending on the Bandwidth key loaded) using the External Network (RS449/V.35/X.21) interface. Note that the physical interface on External Networks is one non-standard 26 pin connector.
Page 199: H.331 Settings
4.8.1.5 H.331 Settings Used when broadcasting a videoconference from one site to many others, e.g. via satellite, where there is no possibility to negotiate quality between the receivers and the originator due to one-way communication. Standard two-way communication with quality negotiation between both sides. Administrator Settings...
Page 200: Lan Settings
TANDBERG 6000 MXP Profile 4.8.2 LAN Settings LAN Settings contain:  IP Settings  H.323 Settings  SIP Settings  SNMP Settings  IP Services  Quality of Service...
Page 201: Ip Settings
4.8.2.1 IP Settings Remember to restart the system after making changes to IP Settings. This can be done by selecting the “Save and Restart” at the bottom of the IP setting menu. Changes in IP Settings menu will not have any effect before the system is restarted. IP-assignment DHCP (Dynamic Host Configuration Protocol) can be selected when a DHCP server is present.
Page 202 TANDBERG 6000 MXP Profile IP Access Password By setting an IP Access Password on the system, all access to the system using IP (Telnet, FTP and WEB) requires a password. The default IP Access Password is “TANDBERG”.
Page 203 Administrator Settings DNS Settings DNS Server 1-5 DNS Server defines the network addresses for DNS servers. Up to 5 addresses may be specified. If the network addresses are unknown, please contact your administrator or Internet Service Provider. DNS Domain Name DNS Domain Name is the default domain name suffix which is added to unqualified names.
Page 204 TANDBERG 6000 MXP Profile 4.8.2.2 H.323 Settings E.164 alias This is the E.164 address of the system. The E.164 address is equivalent to a telephone number, sometimes combined with access codes. Valid characters are 0-9,* and #. When using a gatekeeper, the system will send a message to the gatekeeper containing both the E.164 address...
Page 205 This is the gatekeeper IP-address that is used if you specify H.323 Call Setup: Gatekeeper and Gatekeeper Discovery: Manual. Note that if your system is part of a TANDBERG Expressway™ firewall traversal solution and is placed outside the firewall, you should register the IP address of your Border Controller as the Gatekeeper IP address and set H.323 Call Setup to Gatekeeper.
Page 206 TANDBERG 6000 MXP Profile CallManager Settings CallManager IP This is the CallManager IP-address that is used if you specify H.323 Call Setup: CallManager.
Page 207 Port 1720 Port 5555- 5560 Port 2326- 2365 Please contact your TANDBERG representative for further information. RSVP Auto Resource Reservation Protocol enables the systems to request the optimal amount of bandwidth for the duration of an IP videoconference. Resource Reservation Protocol is switched off.
Page 208 TANDBERG 6000 MXP Profile H.323 Ports Static When selecting static H.323 ports for TCP connections the ports 5555 to 5565 will be used for Q.931 and H.245 respectively. Dynamic The system will allocate which ports to use when opening a TCP connection.
Page 209 4.8.2.3 SIP Settings Mode Setting the SIP mode to on will enable the system for incoming and outgoing SIP calls. Setting the SIP mode to off will disable incoming and outgoing SIP calls from the system. Display Name The Display name part of the SIP Address (URI) is usually a full name or system name. Examples: “Alice Wonderland”...
Page 210 TANDBERG 6000 MXP Profile Server Address The Server Address is the manually configured address for the outbound proxy and registrar. It is possible to use a fully qualified domain name, or an IP address. The default port is 5060 for TCP and UDP, but another one can be provided.
Page 211  Draft-ietf-avt-rfc2429-bis-05.txt - Draft for advanced video signaling including resolution, mpi, annexes and custom formats.  RFC 3047 RTP Payload Format for ITU-T Recommendation G.722.1 Media Capabilities supported in SIP: Audio: PCMU (G.711 u-law) PCMA (G.711 a-law) G.722 64 kbps G722.1 24kbit G.722.1 32 kbps Video:...
Page 212: Snmp Settings
TANDBERG 6000 MXP Profile 4.8.2.4 SNMP Settings SNMP Settings SNMP Trap Host identifies the IP-address of the SNMP manager. SNMP (Simple Network Management Protocol, SNMP Ver 1) is used for monitoring and configuring of different entities in a network. The system's SNMP Agent responds to requests from SNMP Managers (a PC program etc.).
Page 213 Administrator Settings 4.8.2.5 IP Services NTP IP This is the NTP time server address from which the system can get updated time information. The Network Time Protocol (NTP) is used to synchronize the time of the system to a reference time server.
Page 214 TANDBERG 6000 MXP Profile 4.8.2.6 Quality of Service QoS Type No QoS is used. Diffserv Diffserv QoS method is used. Please see below for details. IP Precedence QoS method is used. Please see below for details. Precedence IP Precedence Video Used to define which priority audio, video, data and signaling should have in the network.
Page 215 Administrator Settings Auto will provide the following priority: Audio Diffserv Video Used to define which priority Audio, Video, Data and Signaling packets should have in an IP network. The priority ranges from 0 to 63 for each type of packets. Diffserv Telephony Used to define which priority Audio packets should have in an IP network for telephone calls.
Page 216: Network Profiles
TANDBERG 6000 MXP Profile 4.8.3 Network Profiles This menu consists of 7 network profiles; a prefix can be added for each profile. If you add a prefix to a profile, this prefix will automatically be added in front of the number being dialed.
Page 217: Data Port
4.8.4 Data Port The system provides up to two standard RS232 serial ports to allow a computer to be connected for data transfer and control purposes. Note that when connecting to a PC the connecting cable must be a straight through RS232 cable. Baud Rate, Parity, Databits and Stopbits If you wish to connect a PC to Data port 1, you must ensure that the PC and the system are identically configured.
Page 218: Restore Default Settings
TANDBERG 6000 MXP Profile 4.8.5 Restore Default Settings Restore Default Settings will restore all administrator settings. Note that this will not affect your Call Directory information, Network Type, Line Setup numbers or your SPID numbers.
Page 219: Peripheral Equipment
 Interfaces  Document Camera  VCR / DVD  Additional Cameras  Additional Microphones  TANDBERG DNAM and Speakers  Stereo Speaker Kit  Telephone Add-On  Dual Monitor  XGA Monitors and Projectors  VESA Display Power Management ...
Page 220: Interfaces
TANDBERG 6000 MXP Profile 5.1 Interfaces 5.1.1 Video 5 Video Inputs:  2 video inputs supporting S-Video through Mini-DIN connectors.  2 video inputs supporting composite signals through RCA connectors.  1 VGA/DVI-I (DVI = Digital Video Interface, I = Integrated Digital & Analog) input supporting resolutions SVGA (800x600), XGA (1024x768) and SXGA (1280x1024), analog or digital.
Page 221 LCD monitors and high-end video graphics cards. The TANDBERG codec contains a DVI-I plug that can transmit either digital DVI signals or standard analog VGA signals, depending on what type of monitor is connected.
Page 222 TANDBERG 6000 MXP Profile DVI-D cables transmit digital T.M.D.S. signals, DVI-A cables transmit analog VGA signals and DVI-I cables can transmit either digital or analog signals. It is possible to extend existing DVI cables by the use of extension cables. The maximum cable length however, is 5 meters.
Page 223: Audio
5.1.2 Audio 6 Audio Inputs:  3 microphone inputs (balanced, 24V phantom powered) via XLR connectors.  3 audio inputs (line level) via RCA connectors. All audio inputs are active by default. For further information, refer to chapter Audio. Audio input connector specification: Connector label Microphone(s) Signal type...
Page 224 TANDBERG 6000 MXP Profile Audio output connector specification: Connector label Audio outputs Signal type Unbalanced Connector (codec) Female RCA/phono, sleeve-ground, centre-signal Output impedance 680 ohms Max output level when set 15.3 Vpp to maximum output level Max output level when set 1.15 Vpp...
Page 225: Network
1 x Ethernet (RJ-45 Jack) LAN interface (10/100 Mb) up to 4 or 6 Mbps depending on the bandwidth option installed. To connect the system to a LAN, use the Ethernet cable provided by TANDBERG (or a standard Ethernet cable).
Page 226 Pin-1 Pin-2 Pin-4 Pin-5 Note! TANDBERG recommends always using category 5 cabling. NET Interface: 1 x X.21 / V.35 / RS449 with 1 x RS366 Call Control up to 2 Mbps V35: V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
Page 227 Peripheral Equipment RS449: RS366: All balanced inputs and outputs (A and B) use balanced line signals according to V.11 (RS422) and single ended signals in accordance with V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
Page 228 TANDBERG 6000 MXP Profile All signals are electrically according to RS232. Cable length max: 5 meter X21:...
Page 229 Peripheral Equipment All balanced inputs and outputs (A and B) use balanced line signals according to V.11 (RS422) and single ended signals in accordance with V.10 (RS423). For balanced signals a "0"=low voltage is defined as terminal A positive with respect to terminal For unbalanced signals a "0"= low voltage is defined as terminal positive with respect to GND.
Page 230: Data Port
9-pin D-subs. The TANDBERG main camera is normally connected to data port 2 and pin number 4 provides 12V DC / 1 Amps to the main camera. Otherwise the pin-outs for both data ports are the same.
Page 231: Document Camera
5.2 Document Camera A document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. How to use a document camera with your system: 1. Connect the document camera to the Doc Cam input, if available, on the system. 2.
Page 232: Dvd / Vcr
TANDBERG 6000 MXP Profile 5.3 DVD / VCR Installing a VCR/DVD-recorder/player DVD/VCR Playback Mono For playback, connect a cable between Video Out on the VCR and Video In (VCR) on the system. Connect a cable between Audio Out on the VCR and the Audio In (VCR) on the system.
Page 233 For stereo recording, connect:  Video cable between Video Out 2 on the system to Video In on the VCR  Audio cable between Audio Out 2 (VCR L) to VCR/DVD Audio In (L)  Audio cable between Audio Out 3 (VCR R) to VCR/DVD Audio In (R) Make sure that: ...
Page 234: Additional Cameras
WAVE II -camera number two must be connected to video input 2. Camera number three must be connected to video input 3, and so forth. The maximum length of the camera cable for multiple cameras supported by TANDBERG is 20 m (65 ft).
Page 235: Additional Microphones
Camera Tracking feature. Audio Science Microphone TANDBERG's award-winning Audio Science microphone is a ceiling-mounted, wide coverage, boundary microphone, which can eliminate the need for table microphones. It is designed to pick up the audio from all conference participants seated within in its pick-up area, defined by a quarter-sphere of approximately 14-foot (4.25m) radius extended in front of, and to the sides of...
Page 236 TANDBERG 6000 MXP Profile...
Page 237: The Tandberg Dnam And Speakers
5.6 The TANDBERG DNAM and Speakers 5.6.1.1 TANDBERG 6000 MXP Profile, TANDBERG 6000 MXP, TANDBERG 7000 MXP, TANDBERG 8000 MXP and TANDBERG Maestro The TANDBERG Digital Natural Audio Module, DNAM*: The DNAM audiosystem is built on two specially designed and separate modules; the DNAM audio amplifier and the DNAM loudspeaker cabinet.
Page 238  3 x 50W continuous average Center Output Power (load specified by DNAM Center Speakers).  2 x 50W continuous average Stereo Output Power (load specified by TANDBERG Loudspeaker Stereo Kit).  Full dynamic range for audio (hifi range) ...
Page 239 The DNAM Loudspeaker Cabinet (Center Speakers)*:  3-way Center Speaker system  Frequency range 50Hz - 20kHz  2 x 130mm low- and midrange loudspeakers, 8 ohms nominal, high quality  1 x 25mm dome tveeter, 6 ohms nominal, high quality ...
Page 240 *Note that there are different solutions on integrated audio modules and speakers included in the larger high-end TANDBERG systems. Please contact your TANDBERG representative for more information. ** These are available with the TANDBERG 3000 MXP Profile and TANDBERG 6000 MXP Profile only. The Mini-DNAM amplifier*: The Mini-DNAM amplifier specification: ...
Page 241: Stereo Speaker Kit
Stereo Speaker Kit. Note that if stereo speakers are enabled in the menu without having any stereo speakers connected to the Digital NAM, or having other speakers than the TANDBERG stereo speakers, it may cause the acoustic echo-canceller to malfunction.
Page 242 TANDBERG 6000 MXP Profile...
Page 243: Telephone Add-On
5.8 Telephone Add-On The system has a built in audio bridge* that can bring in Voice over IP (VoIP) telephony or normal telephone sites using ISDN. Note that this requires a system with mixed audio output (audio from local and far end) and one audio input without integrated echo cancelling.
Page 244: Dual Monitor
TANDBERG 6000 MXP Profile 5.9 Dual Monitor Note that this requires a system with dual monitor video output. The Dual Monitor option consists of an additional monitor, bigger cabinet top-plate and associated cabling. The Dual Monitor can be used to show full screen selfview, snapshots and Duo Video.
Page 245: Xga Monitors And Projectors
Peripheral Equipment 5.10 XGA Monitors and Projectors (Optional) The system can be delivered with optional single or dual TV/XGA monitors. It can also be connected to any DVI/VGA/PAL or NTSC display. Note that this requires a system with minimum one DVI-I output.
Page 246: Vesa Display Power Management
In Off mode some power may still be drawn in order to power indicator lights etc. EDID contains the information on which mode a specific monitor supports. TANDBERG supports all four modes. However, in F1 and above, all monitors not listed below are automatically set to Off.
Page 247: Digital Monitor Power Management
5.12 Digital Monitor Power Management DMPM is monitor power management applied over the digital DVI interface. TANDBERG supports DMPM in software F2 and above. Six monitor power states are defined. Monitor On Power state: Transmitter (TANDBERG codec) and receiver (Monitor) are powered and active.
Page 248: Extended Display Identification Data (Edid)
This standard contains information on product ID, basic display parameters, timing identifications and detailed timing descriptions. In F1 and above, TANDBERG will use the EDID information to decide which resolution to use, 800x600 @ 75Hz or 1024x768 @ 60Hz. Example (1024x768@60Hz)
Page 249 Peripheral Equipment Tested and verified monitors, EDID & Timing Listed below are some of the monitors TANDBERG have tested and verified against: ADI A715 Dell W1700 EIZO L367 EIZO F730 ErgoScan 400S Hitachi CM640ET Hitachi CM769ET IBM 9494-HBO IBM G97...
Page 250: Appendices
6 Appendices Appendices:  Appendix 1: Technical Specification  Appendix 2: Bandwidth Information  Appendix 3: Environmental considerations  Appendix 4: Guidelines for setting up videoconferencing rooms  Appendix 5: Security  Appendix 6: Using the file system  Appendix 7: Web Interface ...
Page 251: Appendix 1
H.320 up to 2 Mbps H.323 up to 4 Mbps point-to-point SIP up to 4 Mbps Up to 6 Mbps total MultiSite bandwidth FIREWALL TRAVERSAL TANDBERG Expressway Technology Auto NAT VIDEO STANDARDS H.261, H.263, H.263+, H.263++ (Natural Video), H.264 VIDEO FEATURES...
Page 252 TANDBERG 6000 MXP Profile NTSC, PAL, VGA, SVGA, XGA, W-XGA or SXGA LIVE VIDEO RESOLUTIONS NATIVE NTSC: 4SIF (704 x 480 pixels), Digital Clarity Interlaced SIF (352 x 480 pixels), Natural Video SIF (352 x 240 pixels) NATIVE PAL: 4CIF (704 x 576 pixels), Digital Clarity...
Page 253 System features vary depending on network selection and software package. All specifications subject to change without notice. TANDBERG is a registered trademark or trademark of TANDBERG in the U.S. and other countries. RealPlayer is a trademark or a registered trademark of RealNetworks, Inc. QuickTime is a registered trademark of Apple Computer, Inc., registered in the U.S.
Page 254: Appendix 2
TANDBERG 6000 MXP Profile 6.2 Appendix 2 Bandwidth information for TANDBERG endpoints Model 8000MXP, 7000MXP Bandwidth Standard: 768 / 3072 Point to Option: 1920 / 4096 point ISDN / IP MultiSite Total: 3072kbps 4x768 video + 4 audio 3x1536 video + no audio...
Page 255 4x768 video + no audio 4x512 video + 3 audio Rate Matching Dual Stream (DuoVideo / H.239) Secure All bandwidths Conference H.264 Up to 2Mbps Picture VS, CP4, CP5+1 Mode MultiSite Model 990MXP / 990NET Bandwidth Standard: 1920 (IP Point to only) point Options: 512 / 1920...
Page 256 TANDBERG 6000 MXP Profile Dual Stream (DuoVideo / H.239) Secure All bandwidths Conference H.264 Up to 768 Picture Not Available Mode MultiSite Model 550MXP Bandwidth Standard: 768 (IP only) Point to Options: 128 / 768, 384 point / 768 ISDN / IP...
Page 257: Appendix 3
6.3 Appendix 3 Environmental considerations This section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting By default the system camera will use an automatic iris to compensate for changes in lighting. In addition to this feature, you may further assist the system to maintain the best possible image quality by paying special attention to environmental lighting and background colors as described below.
Page 258: Appendix 4
TANDBERG 6000 MXP Profile 6.4 Appendix 4 Guidelines for setting up videoconferencing rooms The following are a set of guidelines to consider when either building a videoconferencing room, or using an existing room for videoconferencing. Lighting:  Low Contrast desired for light intensity.
Page 259 Appendices The microphone should be placed at the front of the table to ensure that all speech will be detected. The best position for the microphone is at least 2 meters (6.5 feet) in front of the system on a plain, flat table with at least 0.3 meters (12 inches) of table in front of the microphone. The document camera should be close to the chair person or a designated controller of the document camera for ease of use (remember to arrange all the peripherals so that one participant can reach each of them to point, change the display, tape, and so forth).
Page 260: Appendix 5
TANDBERG 6000 MXP Profile 6.5 Appendix 5 Security The system has several features both to protect from unauthorized use and system access: Access Code: When Access Code is enabled, the user will be asked to enter an access code before he/she is able to make a call.
Page 261 All TANDBERG systems support both AES and DES encryption. By default this feature is enabled such that when connecting with any other video system or MCU, a TANDBERG system will attempt to establish a secure conference using AES or DES encryption. The TANDBERG system will attempt this for both IP and ISDN connections.
Page 262 Diffie Hellman key distribution via H.320, H.323 and Leased Line connections. The TANDBERG AES implementation is validated as conforming to the Advanced Encryption Standard (AES) Algorithm, as specified in Federal Information Processing Standard Publication 197, Advanced Encryption Standard, by The National Institute of Standards and Technology...
Page 263: Appendix 6
6.6 Appendix 6 Using the file system It is possible to access a file system within the TANDBERG system by using ftp: DOS- ftp <IP-address of system>, or window: Web- ftp:// <IP-address of system> browser: Description of the different files: all.prm...
Page 264: Appendix 7
TANDBERG 6000 MXP Profile 6.7 Appendix 7 Web Interface It is possible to access and maintain the system remotely via a local area network (LAN) using a standard Web-browser. Connect your system to a LAN with a Network cable. How to configure your system for web interface: 1.
Page 265: Appendix 8
6.8 Appendix 8 (Not available on all TANDBERG systems) Connecting the system to PRI/T1 Using CSU adapter Connecting the system to the ISDN network via the E1/T1-interface using an Adtran T1 ESF CSU ACE or equivalent CSU, will allow up to 1.54 Mbps connection. The E1/T1-interface must be connected to a CSU approved according to IEC 60950, UL 1950 or equivalent standard.
Page 266: Appendix 9
TANDBERG 6000 MXP Profile 6.9 Appendix 9 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapter Connecting the system to the SW56 network using a Telesync Adapter is described below. There are different Telesync Adapters for different configurations of SW56 networks. The network types tested with the system are SW56 2Wire and 4Wire.
Page 267: Appendix 10
Appendices 6.10 Appendix 10 Connecting the system to ISDN using NT1 network adapters Connecting Connect the first ISDN cable from ISDN 1 on the system to the S-interface on your first NT1 network adapter. Connect the other ISDN cables to the appropriate NT1 network adapters.
Page 268: Appendix 11
TANDBERG 6000 MXP Profile 6.11 Appendix 11 (Not available with set top systems) WAVE II Camera Pinouts and Connectors 8-PIN RJ (shielded modular jack): This connector is used for the power and control signals to the main camera. Pin-8 +12V (presence when connected in...
Page 269 This connector is used when cascading cameras: Control (out) signal and external camera detection. Note: It does not provide power for cascaded camera. Pinout Pin-6 Pin-5 Pin-4 RXD (in) Pin-3 TXD (out) Pin-2 Presence (+12V in daisy chain) Pin-1 Multiple Camera support: The figure below is an example of how multiple cameras should be connected: Appendices...
Page 270 TANDBERG 6000 MXP Profile Dimensions Front view: Rear view: Side view: Underside view:...
Page 271: Appendix 12
6.12 Appendix 12 Remote Control (TRC 3) The TANDBERG remote control transmits IR-signals using the following parameters: Protocol Siemens SDA2208 Reference frequency 485kHz Address 4 & 7 IR wavelenght 940nm IR carrier ferquency 30kHz Appendices...
Page 272 TANDBERG 6000 MXP Profile Remote Control keycode map: Button codes Remote control Decimal Address Button codes Button name Decimal NUMBER 1 NUMBER 2 NUMBER 3 NUMBER 4 NUMBER 5 NUMBER 6 NUMBER 7 NUMBER 8 NUMBER 9 NUMBER 0 PRESENTER...
Page 273: Appendix 13
2. The Phone configuration page is located on: device (top menu) -> Add a New device -> Phone -> H.323 Client. 3. In the phone configuration page type the IP address of the TANDBERG system in the Device name field, select device pool and push the insert button.
Page 274: Appendix 14
TANDBERG 6000 MXP Profile 6.14 Appendix 14 Diagnostic Tools for IP To use these tools, will require using a PC and setting up a telnet session towards the system. Q.931 To show Q.931 trace during a call you need to issue the command ‘syslog on’.One can get traces for RAS, Q.931 and H.245 with this command.
Page 275 Function Gatekeeper Discovery (RAS) Q.931 Call Setup H.245* Video Audio Data/FECC MultiSite + Duo Video (*) Note: While using MultiSite, if a site is disconnected and reconnected without terminating the entire conference, the next site to be connected will have a H.245 port outside of the specified range.
Page 276: Appendix 15
Using ISDN A) To upgrade using the the web interface, please do the following steps: 1. Type the IP address of the TANDBERG MXP system that shall be upgraded (for instance 10.0.8.77) in a standard browser, such as Internet Explorer 6.0.
Page 277 Appendices Figure 1 3. Enter the Release key in the ‘Release Key’ field and press the ‘Install Software’ button. A new page will now be displayed:...
Page 278 2. Open a DOS window, and go to the folder where the new software is stored. 3. Type ftp <ip address of the TANDBERG MXP system>. 4. Type in the supplied ‘Release Key’ as user. 5. Type in your IP password (default is “TANDBERG”) as password.
Page 279 2. Copy the new software file to a folder on your computer, for instance c:\software. 3. Type the IP address of the TANDBERG MXP system that the software upgrade is going to be done from (for instance 10.0.8.77) in a standard browser, such as Internet Explorer 6.0. The web interface of the codec will then be displayed.
Page 280 Administrator Settings/General/Permissions menu. 7. Enter the password set at the far end for remote upgrade (default password is “TANDBERG”) 8. Press ‘Install Software' .The system will now use about 90% of the call capacity to transfer the software file across.
Page 281: Appendix 16
Appendices 6.16 Appendix 16 Declaration of Conformity Please contact your TANDBERG representative for a Declaration of Conformity...
Page 282: Appendix 17
TANDBERG 6000 MXP Profile Appendix 17 Dimensions Front view, 50'' monitor...
Page 283 Appendices Front view, 43'' monitor...
Page 284 TANDBERG 6000 MXP Profile Top view, with base Top view, monitor...
Page 285 Appendices Codec...
Page 286: Glossary
Audio input 6: Intended for connection to a VCR or DVD player or other external playback devices. Audio out 1: Intended for connection to TANDBERG Natural Audio, televisions or audio amplifiers. Audio out 2: Intended for connection to audio recording equipment (or to a telephone add-on hybrid).
Page 287 Bandwidth: Decides the quality of the video call. High bandwidth gives high quality. Call control Leased Line: Is a non-dialing protocol and should be used when two systems are connected in a point-to-point connection. Use Leased Line when the handshaking signals DTR and CD are available.
Page 288 TANDBERG 6000 MXP Profile Digital ClarityTF: Participants enjoy presentations of exceptionally high quality resolution video. Disconnect site: As a Chairman, you get the option Disconnect site. Disconnect site allows you to disconnect any participant in the conference. Do Not Disturb: When Do Not Disturb is active the system will not accept any incoming calls.
Page 289 H.264: Video algorithm for bandwidth-efficient video compression and decompression Hardware serial number: A unique number (listed in the System Information menu) to identify your system towards your TANDBERG representatives. Humfilter: A highpass filter which reduces very low frequency noise. iCIF: Interlaced CIF, 352x288 pixels, 50 fields per second...
Page 290 A call with more than two participants including yourself MultiSite: The TANDBERG systems internal MCU. Built-in system which makes it possible to establish meetings with up to 6 video calls and 5 telephone calls. The MultiSite option is not available on all systems.
Page 291 NTSC: National Television System Committee. Video standard corresponding to 4SIF. Primary used in USA, Japan and other countries. Option Key: Required by the system to activate optional features such as MultiSite and Presenter. PAL: Phase Alternation by Line. Video standard corresponding to 4CIF. Primary used in Europe, Middle East and Asia Parallel dial: Channels will be dialed and connected in parallel when setting up a bonding call.
Page 292 Selfview: Outgoing video. In most cases, the image of your self. Serial number: A unique number (the hardware serial number, listed in the System Information menu) to identify your system towards your TANDBERG representatives. Side-by-Side: Side-by-side view means that two pictures are displayed side by side each other on the screen.
Page 293 Terminate meeting: The chairman can terminate the conference, i.e. all participants are disconnected. TMS: TANDBERG Management Suite Touch Tones: To dial extension numbers etc. during a call, use touch tones in order to get tones instead of preset on the number keys.
Page 294 TANDBERG 6000 MXP Profile XGA: extended Graphics Array (1024 x 768)
Page 295: Index
8 Index Access Code...102, 127 Add Another Call...47 Additional microphone ...235 Administrator Password...146 Alert Speaker ...177 Alert Tones and Volume ...177 Allowance ...127 Answer an incoming Call ...52 Assign Floor to Participant...94 Audio Inputs ...169 Outputs...171 Audio Algorithm ...159 Audio Demo ...115 Audio Leveling (AGC) ...176 AudioScience microphone...235 Auto answer...124...
Page 296 TANDBERG 6000 MXP Profile Picture Control ...77 PIP Appearance...154 PIP Placing ...155 Postpone 1 hour ...55 Postpone 3 hours...56 Presentation Presentation Key...80, 151 Presentation Menu ...81 Presentation Source ...151 Presets...75 Production of products... iii Release Chair ...93 Release Floor ...90 Release Floor from Participant ...94...

TANDBERG 6000 MXP Profile User Manual

1 Introduction

2 Installation

3 General Use

4 Administrator Settings

5 Peripheral Equipment

6 Appendices

Appendix 1

Appendix 2

Appendix 3

Appendix 4

Appendix 5

Appendix 6

Appendix 7

Appendix 8

Appendix 9

Appendix 10

Appendix 11

Appendix 12

Appendix 13

Appendix 14

Appendix 15

Appendix 16

Appendix 17

7 Glossary

8 Index

Quick Links

Related Manuals for TANDBERG 6000 MXP Profile

Summary of Contents for TANDBERG 6000 MXP Profile