TANDBERG MXP F8 Administrator's Manual page 170

MXP
Contents Introduction
MENU ADDRESS SETTINGS DESCRIPTION
Control Panel > TV MONITOR FORMAT
General > For wide screen monitors only.
Screen Settings > NORMAL: Output is optimized for normal TV monitors (4:3)
WIDE: Output is optimized for wide TV monitors (16:9). To fully leverage your wide screen display, activate
VIDEO OUT
the Native 16:9 format by setting the TV Monitor Format to Wide.
Control Panel > VGA MONITOR FORMAT
General > For wide screen monitors only.
You should only change this setting if your VGA monitor is a wide screen (16:9) monitor or projector. The VGA
Screen Settings >
and DVI output will then be optimized for Wide Screen VGA and High Definition (HD) display.
VIDEO OUT
NORMAL: Output is optimized for normal VGA monitors (4:3)
WIDE: Output is optimized for wide VGA monitors (16:9). To fully leverage your wide screen display, set the
VGA Monitor Format to Wide.
Control Panel > VGA OUT MODE
General > VGA Out Mode makes it possible to specify which signal to send to VGA/DVI output.
Screen Settings > MAIN: Select Main when you want to use a VGA monitor as your main monitor.
DUAL: Select Dual when you want to use a VGA monitor as your dual monitor
VIDEO OUT
Control Panel > VGA OUT QUALITY SINGLE
VGA Out Quality enables the user to change the preferred format for the DVI/VGA output. It is recommended
General >
to keep this setting in Auto unless your screen doesn't support some of the XGA or SVGA formats the system
Screen Settings >
is using.
VIDEO OUT
AUTO: The VGA output format will be optimized depending on video source format, refresh rate and EDID
information available. Supported formats are:
SVGA (800x600) 75 Hz
XGA (1024x768) 60Hz /75 Hz
WXGA (1280x768) 60 Hz
W720P (if Allow HD720P is set to On)
SVGA 800X600: The VGA output format is forced to SVGA format (800x600) 75 Hz
XGA 1024X768: The VGA output format is forced to XGA format (1024x768) 60 Hz
W720P: The VGA output format is forced to w720p
D14033.06—AUGUST 2010
Getting started The menu structure The settings library The settings library Using the system Physical interfaces Peripheral equipment
INFORMATION
NOTE: You should only change this setting if your TV monitor
is a wide screen (16:9) monitor or projector. All composite- and
S-video output formats will then be optimized for Wide Screen
TV monitors.
If both TV Monitor Format and VGA Monitor Format are
NOTE!
set to Normal, the system will skip the 1+3 layout, which is not
beneficial for 4:3 monitors.
How to set VGA Out Quality for Wide XGA
1. Set VGA Monitor Format
2. Set PC Picture Format
3. Set VGA Out Quality
4. If the layout on the monitor is either full screen or Picture
Outside Picture (POP) and if the input source to the largest
window is PC with resolution 1024x768, then the system will
use WXGA (1280x768) instead of XGA, when the monitor
supports this.
NOTE! If both
set to Normal, the system will skip the 1+3 layout, which is not
beneficial for 4:3 monitors.
The VGA Out port supports VESA Power Management.
If the system is used together with a non TANDBERG supplied
monitor, WXGA will have to be enabled on the dataport as well.
If Allow HD720p is set to On the w720p resolution is added as a
possible resolution for the VGA Out Auto setting.
Administrator Guide
Appendices
to Wide
to Normal
to Auto
TV Monitor Format and VGA Monitor Format
Contact us
PRODUCT
All MXP
systems
which
supports
wide screen
All MXP
systems
which
supports
wide screen
are
3000
990/880/
770
95/85/7
8000
6000
Maestro
3000
1700
990/880/
770, 550
95/85/75
170