TANDBERG MXP F8 Administrator's Manual page 196

MXP
Contents Introduction
MENU ADDRESS SETTINGS DESCRIPTION
Control Panel > STEREO I/O MODE
Audio > ON: If Stereo I/O Mode is On the Audio Input 5 and 6 and Audio Output 2 and 3 will behave as a stereo
input/output pair (VCR-left and right). The VCR Ducking and AGC setting for Audio Input 6 will in this
STEREO SETTINGS
case apply to both Audio Input 5 and 6. The Audio Out 2 (VCR-left stereo channel) will be a mix of the
microphones and the far end left channel. Audio Out 3 (VCR-right stereo channel) will be a mix of the
microphones and the far end right channel.
NOTE:
Interfaces
OFF: If Stereo I/O Mode is Off the Audio Out 2 will be a mix of Audio Input 6, microphones and the far end
(the received far end signal is either mono or stereo that is blended into mono in the near end codec).
Audio Out 3 will be a mix of Audio Input 5, microphones and the far end. Note that stereo speakers set to
On in analog mode will provide a different scheme.
•
If the Out1 Mode is set to Analog mode and the Stereo Speaker is set to On, this will provide a stereo
loudspeaker signal on Audio out 2 and 3.
•
If the Out1 Mode is set to SPDIF mode you are able to receive stereo through Audio Out 1 independent of
the Stereo I/O Mode setting.
•
When both Stereo I/O Mode and Stereo Speakers is set to Off, the output response will be a mono
loudspeaker signal on Audio Out 1, AUX on Audio Out 2 and VCR on Audio Out 3 regardless on the Audio
Out 1 Mode setting.
Control Panel > STEREO SPEAKERS
ON: Set the Stereo Speakers to On to enable stereo output signal to the loudspeaker.
Audio >
OFF: Set the Stereo Speakers to Off to disable stereo output signal to the loudspeaker.
STEREO SETTINGS
When both Stereo I/O Mode and Stereo Speakers is set to Off, the output response will be a mono
loudspeaker signal on Audio Out 1, AUX on Audio Out 2 and VCR on Audio Out 3 regardless on the Audio
Out 1 Mode setting.
D14033.06—AUGUST 2010
Getting started The menu structure
If stereo speakers are set to On in analog mode, they will provide a different scheme. See the
in the Peripheral Equipment section for more information on this topic for your product.
The settings library The settings library Using the system Physical interfaces Peripheral equipment
INFORMATION
DIGITAL NAM (DIGITAL NATURAL AUDIO MODULE)
If the system is connected to a Digital NAM, the stereo sound
on the loudspeakers will be present if a stereo input signal is
connected to the inputs VCR-Left and VCR-Right, or a stereo
signal is received from the Far End.
If the system is not connected to a Digital NAM, stereo sound
on the loudspeaker outputs will be present in the following
situations:
•
If the system is idle and a stereo input signal is connected to
the inputs VCR-Left and VCR-Right.
•
If the system is in a call with the microphone off and a
stereo input signal is connected to the inputs VCR-Left and
VCR-Right, or a stereo signal is received from the Far End.
Otherwise the Loudspeaker Left signal will be equal to
Loudspeaker Right.
SPDIF - Sony/Philips Digital Interface
See the Interfaces in the Peripheral Equipment
information on this topic for your product.
Administrator Guide
Appendices Contact us
PRODUCT
8000
6000
Maestro
3000
Tactical
990/880/
770
95/85/75
section for more 8000
6000
3000
Tactical
Maestro
990/880/
770
95/85/75
196