Menu Selection Details - Yaesu FT-847 Operating Manual

Hf + v-uhf all mode transceiver
Hide thumbs Also See for FT-847:
Table of Contents

Advertisement

Menu System
1
[DIMMER]
Function:
Available Values: 0 (Bright) ~ 7 (Dim)
Default Setting: 0 (Brightest setting)
2
[MIN-FREQ]
Function:
Available Values: 0.1/1/10 Hz
Default Setting: 1 Hz
3
[SSB-CH]
Function:
Available Values: 1.0/2.5/5.0 kHz
Default Setting: 2.5 kHz
The MEM/VFO CH knob is extremely useful for mak-
ing quick frequency excursions. The 5 kHz setting may
be useful for situations when you ask a station to move
"5 kHz U
" for a contact, while the 1 kHz setting is
P
useful for precise tuning of SSB signals. This setting
may be performed individually on HF, 50 MHz, 144
MHz, and 430 MHz.
4
[AM-CH]
Function:
Available Values: 2.5/5.0/9.0/10.0/12.5/25.0 kHz
Default Setting: 5.0 kHz
The 9.0 kHz setting may be useful for channel-by-chan-
nel tuning of AM broadcast stations. This setting may
be performed individually on HF, 50 MHz, 144 MHz,
and 430 MHz.
5
[FM-CH]
Function:
Available Values: 5/6.25/10/12.5/15/20/25 kHz
Default Setting: HF: 5 kHz
This setting may be performed individually on HF, 50
MHz, 144 MHz, and 430 MHz.
84
M
ENU
Setting of the front panel display's
illumination level.
Setting of the minimum synthe-
sizer step size for the MAIN VFO
Tuning Dial.
Setting of the synthesizer steps in
the SSB mode when using the
MEM/VFO CH knob.
Setting of the synthesizer steps in
the AM mode when using the
MEM/VFO CH knob.
Setting of the synthesizer steps in
the FM mode when using the
MEM/VFO CH knob.
VHF/UHF: Depends on trans-
ceiver version (U.S.A., European, etc.)
S
D
ELECTION
ETAILS
6
[CW-PITCH]
Function:
Available Values: 400 ~ 1100 Hz
Default Setting: 700 Hz
The CW sidetone frequency corresponds to the tone
of your signal as heard by another station. Align the
other station's tone pitch to be the same as your CW
sidetone pitch, using the "S
to the other station. The CW Pitch alignment may be
performed in 50 Hz increments.
7
[WEIGHT]
Function:
Available Values: (Dot:Dash Ratio) 3.0:1 ~ 4.4:1
Default Setting: 3.0:1
8
[SIDETONE]
Function:
Available Values: 0 ~ 63 (arbitrary scale)
Default Setting: 32
This CW Sidetone Level adjustment is fixed via this
Menu item, and does not depend on the setting of the
AF (G
) control.
AIN
9
[CW-DELAY]
Function:
Available Values: 10 ~ 300 ms.
Default Setting: 100 ms.
The recovery time may be adjusted in steps of 10 ms.
A longer delay may be preferable if you pause fre-
quently while sending.
Setting of the pitch of the CW
sidetone, CW Spot, BFO offset,
and IF/DSP CW filter center fre-
quencies.
" feature, to "zero-beat"
POT
Setting of the radio between CW
Dashes and Dots for the internal
electronic keyer.
Setting the volume of the CW
Sidetone.
Setting the receiver recovery time
during pseudo-"VOX" CW semi-
break-in operation.
FT-847 O
PERATING
M
ANUAL

Advertisement

Table of Contents
loading

Table of Contents